KAWASAKI Turn Signal Conversion Kit Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Place motorcycle on solid, level ground and on center stand if equipped. 2. Remove your turn signal lens. Place it upside down and clean the lens interior with the supplied alcohol wipe. Allow to completely air dry. Note: the LEDs are mounted to the inside of the turn signal lens with the LEDs making direct contact with the lens. The supplied silicone is used to secure the LED board to the lens. It remains flexible but can be removed. Test fit the board in your lens prior to using silicone. 3. Using a small screwdriver, poke a small hole in the end of the tube of silicone. Place a dab of silicone on each of the 12 LEDs on the circuit board. CAUTION : Note the position of the metal pins on the back of the LED board, They must be located 90 degrees from where the holes are that secure the lens to the housing. See attached diagram. 4. Position the round circuit board over the inside of your turn signal lens with the LEDs facing down. Get the board as centered as possible. Allow the silicone to make contact with the inside of the lens and then push down and slightly rotate the board back and forth to allow the LEDs to make contact with the lens surface. Repeat other side. NOTE : the silicone will require 30 minutes in 70 degree weather to tack up. Full cure will occur within 24 hours. We suggest not riding for several hours if possible to allow the best adhesion. 5. You will need to access the following wires; running light (license plate can be used), brake lights, right turn and left turn. Disassemble the bike as needed to gain access to the wiring

2004 Kawasaki ER5 C5 Service Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
before starting to perform an inspection service or carryout a disassembly and reassembly opera- tionona motorcycle, read the precautions given below. To facilitate actual operations, notes, illustrations, photographs, cautions, and detailed descriptions have been included in each chapter wherever necessary. This section explains the items that require particular attention during the removal and reinstallation or disassembly and reassembly of general parts. Especially note the following: (1) Dirt Before removal and disassembly, clean the motorcycle. Any dirt entering the engine will shorten the life of the motorcycle. For the same reason, before installing anew part, clean off any dust or metal filings. (2) Battery Ground Disconnect the ground (-) wire from the battery before performing any disassembly operations on the motorcycle. This prevents the engine from accidentally turning over while work is being carried out, sparks from being generated while disconnecting the wires from electrical parts, as well as damage to the electrical parts themselves. For reinstallation, first connect the positive wire to the positive (+) terminal of the battery (3) Installation, Assembly Generally, installation or assembly is the reverse of removal or disassembly. However, if instal- lationorassembly sequence is given in this Service Manual, follow it. Note parts locations and cable, wire, and hose routing during removal or disassembly so they can be installed or assembled in the same way. It is preferable to mark and record the locations and routing whenever possible. (4) Tightening Sequence When installing bolts, nuts, or screws for which a tightening sequence is given in this Service Manual, make sure to follow the sequence. When installing apart with several bolts, nuts, or screws, start them all in their holes and tighten them to a snug fit, thus ensuring that the part has been installed in its proper location. Then, tighten them to the specified torque in the tightening sequence and method indicated. If tightening sequence instructions are not given, tighten them evenly in across pattern. Conversely, to remove apart, first loosen all the bolts, nuts, or screws that are retaining the parta 1/4-turn before removing them

Kawasaki Mean Streak 1500 And 1600 BIG SOFT THICK BLANKET Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Place a BIG SOFT THICK BLANKET over your GAS TANK , (LET’S CUT TO THE CHASE, THE MAIN THING IS TO PROTECT THE TANK! ! ! ! ) . 2) You will have to jack up the motorcycle. The best way to accomplish this is with a motorcycle/ATV lift. They are available for a little as $89, and are really an essential tool for maintaining your motorcycle. 3) Remove the stock turn signals completely. They will have to be replaced to do this modification. You may want to install the Kewlmetal turn signal mounts (item #153 or 185) and bullet style signals lights after your fork tubes are in place. 4) Per the Kawasaki service manual, remove the front wheel and be sure to take note of which spacer goes where. Refer to the Service manual for furtherinformation. 5) Remove the front fender Be very careful so you don’t scratch thepaint on the front fender while removing it, the 2 plastic rings holding the front brake lines in place on the front fender will pull out, just make sure to leave them on the lines so they don’t get lost. Now remove the 2 fork guards. 6) Remove the brake calipers and secure the brake pads if necessarywith tape or wire so they don’t fall out. This would be a good time to inspect them for wear, and replace them if necessary. **NOTE** Do not squeeze the front brake lever after you have removed the front wheel. Doing so will cause the calipers to close and then you will have to spread them apart prior to re- assembly. 7) Loosen the bolts on the RIGHT side of the upper and lower tripletree clamps. The fork assembly should drop down. Remove the fork assembly from the bike. 8) Clean the stock fork assembly thoroughly. **NOTE** This kit contains 8 rubber O-rings, (6) Small ones and (2) Fat ones, it is important that these (8) O-rings are placed in the right place for the correct function of the Fat Fork Tubes 9) Slide one of the Small O-rings over the top of the fork assembly until it reaches the bell at the bottom of the shock.

Incoming search terms:

Kawasaki VN2000 LIGHT BAR INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Make certain the motorcycle is securely positioned for this installation. Cover the front fender with a protective cloth to avoid scratches. 2 . Remove caps that cover the headlight screws. Remove headlight screws. (Small Screwdriver and #2 Phillips Screwdriver) Figure 1 and 2. 3. Disconnect headlight at two places. Set light aside. Figure 3. 4. Disconnect the Right (Orange) and Left (Blue) turn signal connectors. 5. Remove the Screws with the 8mm hex head that hold the turn signal bar to the under side of triple clamp. Remove turn signal bar. Bar and screws will not be re-used. (8mm Socket) Figure 4. PREPARATION INSTALLATION 6. Mount the Light Bar Assembly. Hold Light Bar in place at underside of triple clamp. Use the M6 x 16 Screws with a Flat Washer to install the Light Bar assembly. Tighten Firmly. (5mm Hex Key) Figure 5. 7. Route the Light Bar Wires to the back and into headlight shell. WIRE LIGHT BAR HELPFUL WIRE TIPS: A. Keep the Right and Left Wires of the Light Bar in separate groups. B. Inside the headlight shell, the wires bundled in the Blue Connectors are for Right side operation and Orange Connector is Left. C. You will need to remove 2-3″ of electrical tape from the Blue/Yellow Stripe, Low Beam Wire inside the headlight to have room for two Scotchlok Connectors going to this wire. (Scissors) Figure 6

KAWASAKI VULCAN 1500, 1600, 2000 HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Lay a blanket folded several times over the fuel tank to protect it. 2. Loosen (do not remove) from underneath, the two hex nuts holding the risers to the upper triple clamp. (Steering head) 3. Remove the four handlebar clamp bolts. (8mm allen wrench) While sitting on the motorcycle, pull the handlebars and upper clamp off of the risers. They may be slightly stuck and require some force to get free. Lay the handlebar and/or upper clamp/gauge assembly carefully on the blanket. 4. Remove the nuts and risers from the triple clamp. NOTE: Be careful not to scratch the upper triple clamp when installing the new risers. Assemble the supplied lock washers and flat washers onto the supplied bolts. Install the new risers onto the triple clamp and finger-tighten the bolts. 5. Re-install the handlebars and upper clamp/gauge assembly. Tighten the front bolts first closing the gap at the front, and then tighten the rear bolts. Tighten the two riser-mounting bolts securely. Check for adequate clearance and proper routing of cables and hoses.

1999-2002 Kawasaki ZX6R Engine Protection Cage installation instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Follow installation instructions for extended frame sliders. (See page 1) Note: Do not attach delron tips or tighten extended frame sliders until all components are installed. 2. Place the cage loop inside short telescoping tubes on sliders (See fig. G) , push the º”-20 x 1 Ω” bolts through the bolt holes on the telescoping tubes from the outside and start the º”-20 lock nuts to hold cage loop in place. Do not tighten lock nuts at this time. 3. Remove the lower sub frame bolt on the left side of the motorcycle. Install the M10- 1.5 X 88mm stud in place of the sub frame bolt. Place an M10 flat washer and M10-1.5 hex nut on the stud on the interior side of the sub frame. Slide the following components over the stud on the outside of the sub frame in this order: 1.1″ spacer, side strut, (marked with “L”) and M10-1.5 hex nut. (See fig. I) Do not tighten the hex nuts at this time. Repeat for other side using side strut marked with “R”. 4. Push the bottom of the cage loop towards the rear of the motorcycle while pulling the bottom of the left side strut towards the front until the bolt hole on the side strut meets the threaded hole on the tab welded to the cage loop. Attach the side strut to the outside of the tab on the cage loop with a 3/8″-24 x æ” bolt. (See fig J) Do not tighten the bolt at this time. Repeat for other side. 5. Once all components are attached tighten all bolts and nuts. Be sure to torque all engine mount bolts to factory specifications.

Incoming search terms:

Kawasaki Voyager Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Review entire installation manual Remove saddle bags and rear fender cover Modify rear fender bolt slots Install receiver hitch and double check all bolts Remount saddle bags Assemble InstaTrike hitch cart Attach InstaTrike to motorcycle via receiver hitch Attach leanstop brace bolts to receiver hitch Align InstaTrike wheels Double check all bolts for tightness Test ride InstaTrike slowly in an open area to familiarize yourself with handling characteristics Receiver Hitch Installation INSTALL ALL BOLTS AND BRACKETS LOOSLEY UNTIL ALL COMPONENTS ARE IN PLACE! 1) Place motorcycle on its center stand 2) Remove saddle bags and rear fender 3) At the bottom of the rear fender locate two bolt slots. (bolts were removed from these when rear fender was removed) Open the front end of these slots in order to remount fender. 4) Replace bottom fender bolts about 2 or 3 turns. This is necessary to be able to remount rear fender. 5) Attach bracket A to motorcycle. Locate two threaded holes (6mm) near the top of the sub frame. Bolt top of bracket A to these holes. ( bolts provided ) 6) Attach bracket B ( left side ) / C ( right side ) to motorcycle by replacing the bolt that holds the muffler to the frame and vibration absorber with the new bolt provided. Bracket B/C mounts on the outside of the large chrome washer. 7) Attach brackets A, B, C to the hitch ( top ) 8) Replace rear fender 9) Attach brackets D and E to the motorcycle sub frame with U- bolts provided. Attach brackets to hitch. 10) Tighten all bolts and double check. 11) Reinstall saddle bags

Incoming search terms:

Harley Davidson HIGH PERFORMANCE QUICK- INSTALL ADJUSTABLE PUSHRODS INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Remove stock pushrods using a bolt cutter. 2. Place the motorcycle on a hydraulic center stand with the rear wheel raised off the ground. Remove spark plugs. CAUTION 1 WARNING 1 WARNING CAUTION 1 WARNING CAUTION ® i02097.tif Figure 1. Adjustable Push Rod Kit Number 17997-99A Pushrod Tube Adjusting Screw Flats Adjusting Screw Locknut 1 of 2 Exhaust Pushrod Tube has Thicker “Finished” area and is slightly longer Intake Pushrod Tube has Thinner “Finished” area and is slightly shorter 3. With transmission in gear use rear wheel to turn engine over until both front cylinder tappets are at their lowest point. 4. Replace O-rings, lower pushrod cover and spring cover keeper with new components supplied in kit. 5. See Figure 1. Loosen locknut on all of the pushrods and adjust them to their shortest length. NOTE See Figure 1. In Step 6, pushrods with the Thinner “Finished” area on the tubes must be installed to the Intake location on the cylinders; pushrods with the Thicker “Finished” area on the tubes are slightly longer and must be installed to the Exhaust locations on the cylinders. 6. Install pushrods with pushrod covers. Be sure adjuster end of pushrod is down and ball end of adjuster is in tappet socket. 7. If hydraulic tappets are used, adjust pushrods following procedure A. With solid tappets, follow procedure B. NOTE Pushrod adjustment must be made with engine cold. PROCEDUREA (Hydraulic Tappets) 1A. Adjust pushrod length to zero clearance. 2A. See Figure 1. With the pushrod tube kept from rotating with a 1/2 inch or adjustable wrench, slowly turn the adjusting screw with a 5/16 in. wrench, 2-1/2 complete turns counter clockwise (lengthening the pushrod) as viewed from the bottom. (You may wish to mark adjuster to aid in counting turns.) 3A. Hold adjusting screw and tighten locknut with 1/2 in. open end wrench against the pushrod tube. If pushrod turns with locknut use three open end wrenches, one to hold the pushrod tube, one to hold adjusting screw and one to turn locknut.

Incoming search terms:

Yamaha V-Star 650 Rear Lowering Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 18-10-2010

download
INSTALLATION PROCEDURE 1. Secure motorcycle to a bike lift and raise the motorcycle. 2. Remove stock rear shock from the motorcycle per standard Yamaha shop manual instructions. 3. Place the shaft of the shock in V” blocks and secure this in a vice or press, applying firm pressure to the V” blocks to trap the shaft so it will not turn. Unscrew the upper shock mount eyelet from the shaft. NOTE: The upper mount is a standard thread so you will rotate the mount counter-clockwise to unscrew it. 4. Next, screw the New LA Choppers Shock Mount onto shock shaft using Loctite. 5. Re-install shock spring, making sure it is locked in place with the retaining ring prior to slowly releasing the spring compressor. Allow shock spring to expand against the retaining ring and machined washer. 6. Reinstall shock onto the motorcycle per standard Yamaha shop manual instructions. WARNING: Installing a lowering kit will decrease initial ground clearance. The motorcycle will be lower to the ground and care should be taken to avoid bottoming, especially over bumps or in turns. To maintain proper balanced geometry, the front and rear of the motorcycle should be lowered equally. Failure to properly install the lowering kit and operate the motorcycle after installation may result in serious injury or death to the rider. LIMITED GUARANTY: Because we cannot control the application of our products, buyer assumes risks for any and all damage caused to him or herself or any third party by virtue of any failure of these parts. Guaranty for such parts is limited to our replacement costs thereof. This guaranty is in lieu of all other guaranties or warranties express or implied, and all other such guaranties or warranties are hereby expressly disclaimed. By installation of these parts, buyer irrevocably agrees to the foregoing