2002-2003 Yamaha YZF1000 R1 STARTING INSTALLATION

0

Filed Under (Yamaha) by admin on 13-01-2012

download
Remove the main seat and the passenger seat / solo cover. 2 Lift the front of the fuel tank up. 3 Locate the connectors shown in Fig. A. These connectors are located behind the throttle bodies on the left hand side of the bike. 4 Unplug the two connectors shown in Fig. A. Fig.A PLEASE READ ALL THE DIRECTIONS BEFORE STARTING INSTALLATION Unplug these connectors I405-211 6 3 Fig.B 5 Plug the fuel connectors from the PCIII (clear connectors) in-line of the stock wiring harness (Fig. B). Stock connectors PCIII connectors 6 Plug the TPS connectors from the PCIII (white connectors) in-line of the stock wiring harness (Fig. C). Fig.C Stock connectors PCIII connectors I405-211 Trouble Shooting If you feel that you are having any problems at all with the Power Commander III, disconnect it from your motorcycle. This will allow the motorcycle to run directly off of the stock ECU. The lights don’t come on when I turn the ignition switch on. Check to make sure connectors are seated and the kill switch is in the “run” position

Incoming search terms:

Yamaha Royalstar Royal Star Tour Deluxe Speedo Healer Installation

0

Filed Under (Yamaha) by admin on 07-01-2012

download
he speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. – 7/2 -The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. – 7/3 -The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart. – 7/4 -Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. – 7/5 -Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. – 76 -The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

Yamaha XVS 13AW Owner's Manual REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 06-01-2012

download
GASOLINE IS HIGHLY FLAMMA- BLE: Always turn the engine off when refueling. Take care not to spill any gasoline on the engine or exhaust system when refueling. Never refuel while smoking or in the vicinity of an open flame. Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank. If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes

Incoming search terms:

Yamaha V-Star 650 Engine Guard REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Protect the rear portion of the front fender with a towel or other thick, soft cloth. Remove the OEM engine guards if they have been installed on the motorcycle. Your new Barons engine guard will fasten to the frame at the same points as the OEM guard and will use the same hardware. 2. Or, if OEM engine guards are not present, remove the 14mm bolts from the underside of the drivers footpeg mounts. 3. Remove the 12mm upper engine mount bolts located on both sides of the frame. Replacement bolts are included with your new engine guard. 4. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 5. Raise the guard until the holes in the lower mounting brackets align with the vacated bolt holes beneath the drivers footpegs. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the large washers (supplied with the guard) between the rear face of the lower bracket and the frame. The washer fills the space between the lower mounting bracket and the footpeg mount. Reinsert the 14mm bolts and finger tighten. 7. Rotate the guard until the holes in the upper mounting brackets align with the empty holes on each side of the frame. 8. Insert the replacement 13mm bolts, along with their washers, and tighten securely. Tighten all other nuts and bolts securely. 9. Remove the protection on the front fender and you’re ready to ride. CAUTION!!! You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

YAMAHA ROYAL STAR VENTURE CENTERSTAND REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Stand Installation. Locate the four mounting holes on the frame that correspond with the holes in the centerstand. Slide the front of the centerstand up into the frame and align the large bolt holes with those in the frame. Install the (2) 7/16″ x 1″ bolts with washers thru the frame and centerstand. Install the (2) 7/16″ nuts and make finger tight. (on California models the fuel tank vent canister must be removed and the hoses bypassed see note below) Pivot the rear of the centerstand up to align the (2) smaller holes in the stand with those in the frame. Insert a phillips screwdriver into one of the (2) remaining mounting holes and pry the other hole into alignment. Install one of the ¼” x ¾” bolt with a washer from the top down thru the frame and centerstand. Install the lock nut finger tight. Remove the screwdriver and install the remaining ¼”x¾” bolt washer and nut. Tighten the ¼ ” bolts securely 10-12 ft. lbs., then tighten the 7/16″ bolts securely 20-24 ft. lbs. 2. Stop Bumper Installation. Next install the centerstand-stop bumper and bracket onto the frame. Locate the bolt “A” in photo #1. Notice there is another 10 mm bolt just below it. Remove the lower bolt. Attach the bumper bracket to this hole using the longer bolt and washer supplied. The leg of the bracket with the bumper should face inward towards the center of the motorcycle. Adjust the height of the bracket to keep the pedal arm 3/8″ to ½” from the bottom of the exhaust pipe. Tighten securely. 3. Emissions Valve Relocation. You will notice that the right leg of the stand near the foot comes in contact with the emissions valve. The valve needs to be moved outward or to the right as you are sitting on the motorcycle approximately ¾”. This is done as follows: Remove the (2) 10 mm bolts holding the emission valve and bracket to the frame. See photo #2. With the hoses still attached pull the valve down to gain access to the (3) allen screws. Remove the (3) allen screws and (2) nuts holding the bracket to the valve, turn the bracket over and re-assemble the valve onto the bracket as shown in photo #3. Re-install the valve onto the frame. You may need to rotate the hose clamp clips out of the way and/or bend the entire valve bracket assembly outward slightly to gain clearance between the centerstand leg and foot. 4. Using Your New Centerstand. To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now, put all of your weight on to the centerstand pedal (stand on it). Pull up and back on the grab rail using a rocking motion to rock the motorcycle up on to the stand. Remember it is a matter of using your body weight and leverage not lifting! 5. Getting the Bike Down off the Centerstand. Holding the left handle bar and saddlebag guardrail, firmly rock the motorcycle off the centerstand. You can also rock it off while sitting on the motorcycle.

650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

YAMAHA V-STAR 650 CA SHORTSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
Check condition of stock exhaust gasket. Replace if damaged or worn. 2. Install mounting bracket (stamped 384-P) in the original bracket mounting position using two 8mm bolts (supplied)(Figure 1). Note: Install two 5/16″ x 5/8″ fl ange bolts (supplied)(Figure 1) into top holes of bracket before installing bracket onto motorcycle. 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffl er onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 2). #20 hose clamps are for head pipes and #28 hose clamps for muffl er area. Take note of clamp screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install 6″ fl ange bolts (supplied) engaging nut plate. Leave T-bolt clamp onto front muffl er (Figure 4&5). Slide muffl er onto front head pipe. Slide nut plate (supplied) inside bracket welded to backside of front muffl er (Figure 6). Attach muffl er to mounting bracket 384-P using two 5/1head pipe/muffl er assembly loose at this time. 6. Using stock Allen bolts, carefully install rear head pipe/ muffl er assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide nut plate (supplied) inside bracket welded to backside of rear muffl er (Figure 6). 8. Align muffl ers so they are parallel when viewed from the right side of the motorcycle and muffl er tips align at the same length. Tighten 5/16″ fl ange bolts securing muffl ers to bracket. 9. Tighten cylinder exhaust port bolts securing head pipes to cylinder head. 10. Tighten T-bolt clamp securing front muffl er to head pipe. 11. Adjust heat shields so that muffl er tips protrude 1/4″ from heat shields (Figure 7) and rotation of heat shield matches muffl er tip. Tighten all hose clamps securing heat shields. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. Note: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up. 13. All hardware must be properly tightened before starting motorcycle

HONDA CR 500R/ 500AF Hi Power Digital Ignition AND Light Coil Installation Instructions

0

Filed Under (Honda) by admin on 16-12-2011

download
Place the motorcycle on a secure stand. 2.Remove the fuel tank and radiator shrouds. 3.Remove the front number plate if CDI unit is located behind number plate. 4.Remove CDI Ground from coil. 5. Remove Old CDI. 6. Remove ignition cover. 7. Use an electric, pneumatic impact to remove flywheel nut. 8. Use flywheel puller to remove flywheel. Thread the flywheel puller into the flywheel by turning the puller counter clockwise (left hand thread). Turn flywheel puller center nut clockwise with an impact set to low to remove flywheel. 9. Remove 2 bolts that secure the stator.
10. Remove stator. 11. Install new stator by aligning the index mark on the lower stator plate with the index mark on the left crankcase. 12.Install and tighten stator bolts to 9 ft-lbs. (1.2 kg-m). 13. Install new flywheel and tighten flywheel nut to 40ft-lb (5.5 kg-m). 14. The pulser gap is preset to .012″. If you have trouble starting you bike after installation confirm the gap between the pulser and the ignition trigger on the flywheel is .012″. Use a good/no good technique when checking and adjusting the gap. The largest feeler that will fit without forcing the feeler into the gap is the current gap. 15. If the pulser gap needs to be adjusted loosen the pulser mounting bolts adjust the pulser up or down as needed

HONDA CB25O NIGHT HAWK OWNER’S MANUAL

0

Filed Under (Honda) by admin on 29-11-2011

download
The motorcycle presents you a challenge to master the machine, a challenge to adventure. You ride through the w1nd_, linked to the road by a vehicle that responds to your commands as no other does. Unlike an automobile, there is no metal cage around you. Like an airplane, a pre-ride inspection and regular maintenance are essential to your safety. Your reward 1S freedom. To meet the challenges safely, and to enjoy the adventure fully, you should become thoroughly familiar with thls owner s manual BEFORE YOU RIDE THE
MOTORCYCLE. When service is required, rememher that your Honda dealer knows your motorcycle best. If _you have the required mechanical know-how and tools, your dealer can supply you with an official Honda Service Manual to help you perform many mamtenance and repair

2010 RIDGELINE MOTORCYCLE BED EXTENDER INSTALLATION AND REMOVAL

0

Filed Under (Honda) by admin on 26-11-2011

download
Using an awl, pierce through the seals in the holes on the left side bed lining Install the left latch to the left side bed lining with three hex bolts While wearing eye protection, drill a 3 mm hole at the mark on the left side of the tailgate. Widen the hole with a 8 mm drill bit. To prevent damage to the inner vehicle parts, wrap a tape around the drill bit tip to the root in the measurement as shown. Remove any burrs Align the non-threaded wedge with the threaded wedge at three joints between the left and center tubes, then secure the wedges with one T-20 torx screw each.

Incoming search terms: