Kawasaki ZX-9R Ninja TiForce exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 07-05-2012

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN.

Kawasaki KVF650/ 700, KSV 700 Camshaft Installation Instructions

0

Filed Under (Kawasaki) by admin on 29-04-2012

download
Liberally apply assembly lube to every surface of the camshaft. Install the camshaft into the cylinder head (the lobes should be pointed down) and align the decompressor shaft dowels with the weight arms. Install one of the camshaft sprocket holder bolts and tighten to less than finger tight, you should be able to move the camshaft very slightly back and forth, roll the crank over until the other bolt hole is exposed and insert the sprocket bolt and tighten to less than finger tight. Install the cam chain tensioner assembly, do not install the spring, spring dowel, washer, and bolt. Using the spring from the cam chain tensioner very slowly push the tensioner shaft in until the cam chain slack has just been taken out, this is witnessed by the very slight lifting of the opposite end of the cam out of the cylinder head cam journal, do not over tighten the cam chain at this point, if you do, remove the tensioner assembly and retract the plunger again and start over. (If it stays too tight it will stretch the cam chain prematurely and cause cam sprocket damage when the engine is assembled) Roll the camshaft toward the back of the machine (clockwise) loading the sprocket bolts against the back of the sprocket bolt holes, while holding the camshaft in that direction, tighten the sprocket mounting bolt to 14 ft/lb of torque. Rotate the engine in the opposite direction that you rotated it earlier and align the TDC mark, tighten the other sprocket-mounting bolt to 14 ft/lb of torque. Verify the cam timing and crankshaft TDC marks are in alignment

Incoming search terms:

1982-2005 Harley Motorcycle Removal and Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Remove the motorcycle seat. Remove the aft mounting bolts on the fuel tank. 7 Guide the Signal® mirror wire harness along the inside of the fuel tank’s front mounting bolt and between the crossover tube. 8 9 Lift up the aft portion of the fuel tank and guide the Signal® mirror wire harness down the backbone of the motorcycle frame, alongside the existing factory wire harness. The motorcycle’s electrical wiring for turn indicators is located aft of the gas tank on the backbone of the frame. Guide the new wire harness from the Signal® mirror to the electrical wiring. Cut off any excess slack in the wire. Locate the SOLID BROWN wire from the wire connector. Turn the ignition key so that electrical power is on and activate the right side turn indicator. Probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘right side turn’. Repeat all of the previous steps to replace the left side factory mirror with the new Signal® mirror. Locate the SOLID VIOLET wire from the wire connector. Activate the left side turn indicator and probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘left side turn

Incoming search terms:

HARLEY-DAVIDSON SPORTSTER MODEL'S 215 and S 215 INSTALLATION and CLEANING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 16-03-2012

download
1. Refer to Figures 1 & 2. 2. Remove taillight and remove seat. SAFETY: DISCONNECT BATTERY PRIOR TO ALL WIRING MODIFICATIONS 3. Disconnect Right turn signal connector inside taillight. Pull wire from the underside of fender. Cut the wire approximately 2 inches from the connector, 02/16/09 save for reinstallation. Ensure the wires are loose from all retaining clips under fender. 4. Remove nut located behind fender holding the turn signal. 5. On the right side only, Remove the two torx bolts from fender strut, carefully pull and rotate fender strut cover to remove. Pull turn signal wire completely out. Remove bolt holding turn signal to the fender strut cover. SADDLEBAG INSTALLATION 6. Reinstall the fender strut cover using the 1 7/8″ Hex Spool Bolt Assembly and 1/8″ x 5/16″ Aluminum Spacer in the front hole and the 1 1/2″ Hex Spool Bolt Assembly and 1/8″ x 5/16″ Aluminum Spacer in the rear hole. Refer to view “B”. Insert the chrome caps into the existing turn signal holes. Bend tabs over to ensure a snug fit. 7. Repeat disassembly and installation on opposite side. TURN SIGNAL RELOCATION 8. Install turn signal bracket between license plate and license plate bracket with ears of bracket facing the front of the motorcycle, using 1/4 – 20 x 3/4 Hex cap screws, 1/4 flat washers, and 1/4 – 20 locknuts. 9. Mount turn signals directly to bracket using 5/16 – 18 x 3/4 hex cap screws with a Black Plastic Spacer, and 5/16 star washer. For a clean installation slide rubber grommet over the wire and secure into hole in turn signal, remove top center mounting bolt on license plate bracket and run wires through this hole. Splice the connector back on the wire, and reconnect to wire harness. Ensure all wires are secure under fender. Reinstall taillight. 10. Connect battery and test turn signals for function. Information: Bags will be easier to mount and remove if a small amount of silicone lubrication is applied to rubber mounting points. 11. Mount saddlebags over spools on fender strut and secure with clips retained inside bags. 12. Inspect each clip to verify each clip is properly seated in retaining groove. See View “A”

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

R1 Addendum Yamaha YZF-R1 and YZF-R6 TiForce exhaust system REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-01-2012

download
Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide more access to the exhaust nuts (flange nuts). 2. YZF-R1 ONLY!!! The EXUP control cables are tie-wrapped to the frame, and will need to be disconnected from the servo motor. Do not disconnect the electrical connection to the servo motor, and do not remove the actual servo motor. Simply remove the cables from the EXUP valve and from the servo motor. 3. Remove the existing exhaust system and save the flange nuts for reuse. Save the mounting bolt and nut for the end can to the passenger footpeg for reuse as well. 4. Inspect the exhaust gaskets. Replace if necessary. 5. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remainingsteps. Reuse the flange nuts saved from step 3 above. Make sure the ends of the headpipes fit flush and snug in the ports before tightening. 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 10. YZF-R1 ONLY!!! Place the bands approximately 180mm from the edge of the end can. See figure 2. 11. YZF-R6 ONLY!!! Place the bands approximately 195mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (step 10 or 11 / figure 2), then tighten the 6mmhardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN

Yamaha YZF-R1 and R6 TiForce slip on exhaust system REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-01-2012

download
1. Remove the fairing lowers. 2. For R1 owners, please remove the existing exhaust system from the EXUP valve rearward (EXUP valve is retained) and set aside. Save the stock exhaust clamp for reuse. For R6 owners, please disconnect the stock S-bend from the rear of the collector and set aside. Save the stock exhaust clamp for reuse (new clamp provided). Save the stock end can mounting bolt for reuse as well. 3. R1 owners only -Inspect the exhaust gasket. Replace if necessary (gasket provided). 4. For R1 owners -Install the S-Bend to the rear of the EXUP valve, make sure the system fits flush. Reuse the stock exhaust clamp to connect the S-bend to the valve. For R6 owners -Install the TiForce S-bend to the rear of the stock head pipes and collector. Make sure the system fits flush and snug. Reuse the stock exhaust clamp or the provided clamp and loosely attach for now. 5. Install the TiForce end can to the S-bend tail pipe. 6. Loosely attach the two rubber bands, stainless steel bands (K), and stay to the end can using the supplied 6mm hardware (H) and the hanger / stay arm (G). See figure 1 for the assembly procedure. 7. R1 owners -Place the bands approximately 180mm from the edge of the end can. See figure 2. R6 owners -Place the bands approximately 195mm from the edge of the end can. See figure 2. 8. R1 owners -Using the stock provided mounting point on the passenger footpeg, use the M10x45mm bolt and hardware to mount the end can loosely, allowing for some adjustment. 9. Carefully align the two stainless bands so that theyare parallel to each other, and spaced properly on the can. Tighten the 6mm hardware (H). Make sure that the rubber pads fully cover the bands (K). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 10. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire TiForce exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 11. Attach the supplied springs to secure the end can to the S-bend pipe using a spring installation tool if available. Make sure the exhaust system is free and clear of the bike. If necessary, adjust for proper clearance. 12. Go back and tighten all fasteners. 13. Check that all fasteners are tightened per specifications, then start the motor and check for exhaust leaks. 14. Reinstall the fairing lowers.

Incoming search terms:

Yamaha FZ-1 TiForce exhaust system Installation Instructions (Slip-on)

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Loosen the clamp where the stock tailpipe connects to the stock collector. 2. Remove the bolt holding the stock muffler assembly to the footpeg/exhaust bracket. 3. Remove the stock tailpipe and exhaust assembly as one piece. 4. Remove the nut securing the right side center stand support bolt. Install the new supplied bracket as shown in (See figure 1) 5. Remove the right rear footpeg assembly complete, bolt the new footpeg mounting bracket in place of the stock one using supplied bolts. 6. Carefully unbolt the footpeg from the bracket (Be careful there are springs and washers that will fall out if you are not careful), bolt the footpeg into the new billet footpeg bracket. Bolt the footpeg bracket to the footpeg- mounting bracket. (See figure 2) 7. Remove the stock exhaust gasket from the stock tailpipe and installthe gasket into the new tailpipe. 8. Slide the supplied clamp over the new tailpipe and slide the new tailpipe onto the stock collector. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 4. 10. Place the bands approximately 150mm from the edge of the end can. See figure 5. 11. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to connect the tailpipe and muffler assembly. 13. Make sure the exhaust system is free and clear, if necessary jigglethe system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (figure 5), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure thatthe rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Tighten the supplied clamp to secure the new tailpipe to the factory collector. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Check that all hardware is tightened, then start the motor and check for exhaust leaks.

Incoming search terms:

HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

VT 1100 TEARDROP SPECIFIC-FIT SADDLEBAGS INSTALLATION

0

Filed Under (Honda) by admin on 23-11-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets