KAWASAKI ZX-6R/ RR Carbon Fiber /Aluminum Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1 After bike is cool make sure the bike is secured before beginning the installation. 2 Remove the fairing retaining clips and mounting bolt. Remove the stock mid pipe and muffler. 3 Apply a small amount of high temperature silicone (such as Permatex Ultra Black) to the inside of the exhaust inlet. 4 Attach the LOR exhaust canister to the slip-on tube adapter with the spring tabs aligned (make sure your hands are protected with a pair of gloves in case the tubes slip). You may have to squeeze the mid-pipe adapter tube to fit into the exhaust inlet as the mandrel bends may become slightly out of round due to a cut near the bend (the tube will take form once connected). Slide the canister all the way until the slip-on adapter seats fully against the exhaust inlet. Wipe off any excess silicone. 5 Place each spring over the exhaust side spring tabs and use the spring tool to pull the springs over the adapter spring tabs. Both springs must be secured for proper installation. 6 Apply a small amount of silicone sealer (such as permatex Ultra Black or Ultra Copper) to the inside (inlet side) of the slip-on adapter. Slide the low profile barrel clamp over the LevelOne Adapter pipe. Slide the slip-on adapter pipe over the stock header collector. Do not fully tighten the barrel clamp. 7 Place the round canister clamp with the rubber gasket over the rear of the exhaust and slide to the clamp location. Insert the original stock screw and 8mm washer through the exhaust clamp and finally through the foot peg. Mount the clamp to the outside of the stock muffler bracket. On the opposite side (towards the bike) place the stock 8mm lock washer and stock 8mm nut and start the thread. Do not fully tighten at this time. 8 Standing at the rear of the motorcycle, check the alignment of the muffler. You can adjust/rotate both the exhaust and mid-pipe adapter until the muffler is aligned properly. 9 Once everything is aligned fully tighten the exhaust canister clamp. 10 Fully tighten the low profile barrel clamp over the stock header. 11 Before you start the bike make sure all fingerprints and dirt have been removed from the canister and slip-on adapter. You may use rubbing alcohol to clean the slip-on adapter. After 75-100 miles check all bolts, etc for tightness. It is recommended to apply some light – medium grade thread locker to prohibit any bolts from loosening under the vibration from the bike. 12 Enjoy your LevelOne Racing exhaust system

kawasakI 9400 hyPercharger kIt INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
steP 1 Remove the seat. steP 2 Remove the bottom of the three dash plaque bolts (8mm). steP 3 Lift up on the dash panel and unscrew the speedometer cable (knurled nut). steP 4 Unplug the three electrical connections. steP 5 With a 12mm socket, remove the tank-mounting bolt under the dash and at the rear of the tank. steP 6 Close the fuel valve and clamp off the fuel line. Disconnect the line from the fuel valve. steP 7 Raise the rear of the tank, and disconnect the two vent hoses, and remove the tank. steP 8 Refer to the section of your factory service manual that deals with removal and installation of the following components. • Remove the two round chrome “air cleaner covers”, their backing plates, the stock black plastic air box (air inlet under tank), and the crossover tube. • Remove the intake manifold to remove and crossover tube. Use extreme care when replacing the intake manifold. Uneven torque, damage to the intake gaskets, or contamination can cause an intake leak that will result in very poor running, and nearly impossible jetting!! • Unplug all hoses or lines from these components. You may want to label these hoses at this time. The Largest of these hoses (3/4″ I.D.) is for the fresh air injection system; the second largest (3/8″ I.D.) is the crankcase breather. The smallest of the hoses is a drain. steP 9 Remove the brackets that held each round backing plate. The right hand bracket is also a carb stabilizer. This function is duplicated with one of the included brackets. steP 10 Remove the carburetor according to the section in your factory service manual that outlines procedures for carburetor removal, disassembly, reassembly and installation. We recommend that you label each hose or fitting as they are removed to make reassembly easier. An example of hose labeling is shown in PIC. 1. carburetor re-jettIng Procedure note Different combinations of aftermarket exhaust and air cleaners will have a significant impact on carburetor jetting. The supplied jetting components have been tested and found to be a good combination to produce drivability and performance with stock or free flowing, muffled/baffled exhaust pipes. We highly recommend NOT using drag pipes (open style). Using drag pipes in conjunction with our air cleaner will require additional jetting above and beyond the components included in this kit. a) Consult your factory service manual for details of this procedure. We have supplied jets to cover many common configurations. Remove the four Phillips head screws securing the plastic carb top to the carb body. Carefully remove the plastic carb top making sure not to damage the rubber diaphragm.

Incoming search terms:

Kawasaki KLX450R Dual Sport Kit Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the seat, fuel tank, and side panels. 2. Unplug and remove the stock headlight. 3. Taillight Installation: The Baja Designs taillight will run in conjunction with the stock taillight for this installation. Start by removing the first wire guide that the stock taillight wires pass through near the end of the fender. Once removed, trim off the remaining molded mounting boss as shown in Photo 1. Drill three ¼” holes in the fender and use the provided countersunk mounting hardware to attach the Baja Designs taillight as shown in Photo 2. The rear edge of the LED cluster should line up with the rear edge of the fender. Route the wires forward between the plastics to the left of the front mounting bolt. We’ll attach them in a later step. Photo 1 Molded mounting boss removed Stock taillight Photo 2
4. Turn Signal Installation: Drill a 7/16″ hole in each side of the fender plastic in the locations shown in Photo 3. Install the rear turn signals and route the wires forward as shown in Photo 4. Photo 3 Photo 4 Zip-tie BD taillight wires to fender here Route left signal wires through fender with stock taillight wires 5. Brakelight Switch: The KLX uses a hydraulic operated switch to activate the brakelight. Installation of this switch requires bleeding the rear brake system. If you do not feel competent performing this task please refer it to a qualified mechanic. An improperly bled brake can lead to rear brake failure. Caliper Guard Modification: The hydraulic brakeswitch replaces the banjo-bolt that attaches the rear brake hose to the caliper. Because of its larger size, the plastic caliper guard must be relieved slightly to provide clearance. Remove the caliper guard and modify as shown in Photo 5.

Kawasaki ZRX-1100 / 1200 exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 2. Inspect the exhaust gaskets. Replace if necessary. 3. Attach the head pipes 1, 2, 3 , and 4 to the exhaust ports of their respective cylinders, using the flange nuts saved from step 1 above. Loosely apply the flange nuts for now, allowing for ome adjustment. 4. Attach the Y-pipe collectors to the head pipes. Please note that one collector goes to pipes #1 and #4 and one collector goes to pipes #2 and #3 (collectors are labeled). Make sure the ends of the head pipes fit flush and snug in the ports. Do not install the springs at this time. 5. Install the S-Bend to the rear of the two Y-pipe collectors. Do not install the springs at this time. 6. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes are centered in each port. 7. Slide the TiForce end can into place on the S-bend pipe. 8. Loosely attach the two rubber bands, stainless steel bands K, and the stay / hanger G, to the end can using the supplied 6mm hardware H. (See figure 1) . Make sure that the rubber bands fully cover the stainless bands to prevent scratches to the can. 9. Place the bands approximately 108mm from the edge of the end can. (See figure 2) . 10. Go back and tighten the exhaust flange nuts per factory specification. Do not over tighten. 11. Using the stock provided mounting point on the right passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 13. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 16. Check that all hardware is properly tightened, and then start the motor and check for exhaust leaks

Incoming search terms: