Kawasaki Sxi/ SXR Ignition twin cylinder Jet Ski ignition Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove electronics enclosure from its mounting location. 2. Unplug and remove the OEM ignition. 3. Set the programming switches on the T3 to your settings. 4. Install the T3 Ignition in the same location in the electronics enclosure. 5. Test the T3 Ignition. 6. Close the electronics enclosure cover plate and mount the module in the PWC. Installation Remove electronics enclosure from its Mounting Location 1. Using a 10mm socket remove the mounting bolts on each side of the electronics enclosure. 2. Remove the enclosure cover and set aside the screws, 2 mounting flanges, ‘O” ring, and enclosure top. Unplug and Remove the OEM Ignition 1. Using 10mm socket, remove bolts from each side of the OEM ignition. Lift out the ignition and unplug all connectors attached to the OEM ignition. Now remove the protective metal plate that was under the ignition and two 3/16″ thick washers under that plate. 2. On 2004 models and newer remove the wire harness for the two black connectors just unplugged from the OEM ignition. Trace each wire from each black connector back to in-line connectors and separate each of these connectors. Set the two harnesses aside. Install the T3 Ignition in the Electronics Enclosure 1. Install the T3 ignition into the mounting bracket supplied with your T3. Slide the end of the ignition module under the lip at the rear of the bracket an press the wire end of the ignition firmly into the bracket. Attach the keeper bracket using two 5mm bolts supplied. Place the ignition/bracket in the location where the OEM ignition and metal plate were removed. Secure the ignition in place with the supplied bolts

Incoming search terms:

Kawasaki Teryx Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figures 1 Below – place UTV Roof Mounting Brackets on Roof and using a marker, mark the position of the holes needed for each Roof Mounting bracket . For rear of roof mounting, use existing slotted bracket and mark one hole through the factory slotted brackets as shown in Figure 2. Figure 1
Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 Figure 2 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in between holes to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figure 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 3. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Kawasaki VN2000 Passenger Floorboards/ Passenger Longboards Installation And Adjustment

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Fasten floorboard assembly to mounting bracket using supplied 3/8″ x 3/4″ bolt, flat washer and lockwasher. Do not tighten at this time (Baron recommends the use of blue Loctite on this bolt). 2. Set floorboard angle by installing flathead allen adjusting screw in the pivot bracket at the desired angle hole. Baron floorboards set to a 15-degree position has been found to be most comfortable and user friendly. Tighten flathead screw. Adjust side tilt angle by moving floorboard stop screw in or out to achieve desired angle. 3. Now fully tighten the 3/8″ bolt. Floorboard is ready for installation. Installation 1. Remove the nuts that attach your stock passenger peg mounting brackets to the frame and remove stock pegs. 2. Install your new Baron floorboards in the same location using supplied M8 mounting bolts and washers. Be sure you dont over-tighten these bolts. It is best to use Loctite when mounting. Adjustment of Floorboard Angle After Installation 1. Using a 9/16″ wrench, slightly loosen the 3/8″ bracket bolt located on the backside of the mounting bracket the floorboard is attached to. 2. Remove the small allen screw located on visible side of the cam bracket. Once this screw is removed, adjust the cam to the desired hole and insert and tighten allen screw. 3. Re-tighten 3/8″ bolt. Repeat process on both sides. NOTE: All adjustments may not be available with all exhaust systems

Incoming search terms: