HONDA VTX 1300 Retro BIG SHOTS EXHAUST SYSTEM INSTALLATION

0

Filed Under (Honda) by admin on 07-12-2011

download
Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install and tighten supplied mounting bracket (stamped
346-P) in the original mounting bar location, using two M10x40 flange bolts, nuts, and washers (supplied) (Figure 1). 3. Install and tighten rectifier using M6x30 flange bolt, nut, and washer combinations (supplied)(Figure 1). 4. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker, mark the outside surface of front and rear heat shields with the location of the mounting clips welded inside(Figure 2). 5. Install each heat shield over its respective head pipe (Figure 3). 6. Install each hose clamp by feeding tail end of clamp into heat shield clip. Take note of clamp screw head direction (Figure 2 & 4). Screw head should be ccessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas. Note: Prior to tightening hose clamps, align end caps so that slash ends are even.

HONDA AERO 750 CRUZER EXHAUST SYSTEM REMOVAL And INSTALLATION

0

Filed Under (Honda) by admin on 18-11-2011

download
Install mounting bracket (stamped 363-P) in the original muffler mounting position, using two 10mm bolts and
one 10mm nut. (supplied)(Refer to figure 2). 2. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside.(Refer to figure 3).Place each heat shield on a non-abrasive surface such as a blanket or carpet. Position each head pipe/muffler over its respective heat shield. (Refer to figure 4).
3. Feed tail end of each hose clamp through each mounting clip welded to back side of front and rear heat shields. Take note of clamp hex screw head direction. (Clamp head direction is critical for adjustment when system is installed on bike.) Wrap each clamp around back side of head pipe threading tail end into clamp head. (Refer to figure 3 & 4).
4. Install front head pipe/muffler using stock flange nuts. Slide dog bone shaped nutplate (supplied) inside
bracket welded to backside of muffler. Attach muffler to mounting bracket 363-P using (supplied) 5/16” flange
bolts engaging dog bone nutplate. Leave head pipe/muffler assembly loose at this time (Refer to figure 4). Repeat this step with the rear head pipe.5. Align mufflers so they are parallel when viewing from right side of the motorcycle. Tighten 5/16” flange bolts securing upper and lower muffler positions.. Tighten cylinder exhaust port flange nuts securing head pipes to cylinder heads. 7. Adjust heat shields so they meet front of muffler taper. (Refer to figure 6). Tighten all hose clamps securing heat shield locations. NOTE: Heat shields should cover muffler/head pipe weld joint.

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms:

HONDA SHADOW AERO 750 STRAIGHTSHOT HS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 03-11-2011

download
Install mounting bracket (stamped 359-P) in the original bracket mounting position, using two 10mm bolts and
one 10mm nut (supplied)(Figure 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark the outside edge of each heat shield to show location of hose clamp mounting clips (Figure 3). 3. Slide flanges onto head pipes and lay head pipes into
heat shields. Loosely install hose clamps by feeding tail end of clamp into heat shield clips (Figure 3). Take note of screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas.
4. Using stock nuts, carefully install head pipes into exhaust ports (Assistance may be required). NOTE: Do not tighten at this time.

2008 Matrix FRONT LICENSE PLATE MOUNTING BRACKET INSTALLATION DURING PDS

0

Filed Under (Toyota Manuals) by admin on 19-10-2011

download
Using the two self-tapping screws, install the mounting bracket to the front bumper. NOTE: Do NOT drill holes in the dimples. Tighten the driver’s side screw first and then tighten the passenger’s side screw. 3. Install the front license plate to the bracket using non-corroding self-tapping screws of the following size

Toyota Power Steering Conversion Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
Remove the stock steering box and column. Be sure to clear the area of all wiring, brake lines and fuel lines. 2. Bolt the Toyota box to the mounting bracket so that the long arm of the bracket points in the same direction as the steering column input shaft (small shaft.) To mount the bracket and box correctly, the longer end should be towards the rear of the vehicle. It may be necessary to grind on the power steering box where the two flanges protrude above the bracket. For technical help call Classic Performance Products Monday thru Friday 8:30am to 5:00pm at (714) 522-2000. Rev. 8/17/2009 3. Locate the box/bracket assembly into the frame by centering the Toyota sector shaft through the original hole in the frame. This hole will need to be elongated approximately 3/8″ to allow the sector shaft to clear the frame. Bolt the bracket directly into the mounting holes for the original steering box. 4. With the first bolt in, check the fit by reattaching the steering box. Make sure the splined shaft goes through the frame without interference. Torque down the mounting bolts to 45 lbs. 5. Attach the pitman arm to the steering box. Before this is done the steering sector must be centered. Turn the input shaft clockwise as far as it can go. Make a reference mark. Now turn the shaft counter clockwise as far it can go and be sure to count the turns. Turn the shaft back half the distance and now the box is centered. Be sure to double and triple check this procedure. Attach the pitman arm to the output shaft with the output shaft nut. Torque the bolt down to 110ft/lbs. Reconnect the stock drag link and you are on your way

Incoming search terms:

1953 Toyota Ford Truck Power Steering Conversion Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 01-10-2011

download
of all wiring, brake lines and fuel lines. 2. Bolt the Toyota box to the mounting bracket so that the long arm of the bracket points in the same direction as the steering column input shaft (small shaft.) To mount the bracket and box correctly, the longer end should be towards the rear of the vehicle. It may be necessary to grind on the power steering box where the two flanges protrude above the bracket. For technical help call Classic Performance Products Monday thru Friday 8:30am to 5:00pm at (714) 522-2000. Rev. 8/17/2009 3. Locate the box/bracket assembly into the frame by centering the Toyota sector shaft through the original hole in the frame. This hole will need to be elongated approximately 3/8″ to allow the sector shaft to clear the frame. Bolt the bracket directly into the mounting holes for the original steering box. 4. With the first bolt in, check the fit by reattaching the steering box. Make sure the splined shaft goes through the frame without interference. Torque down the mounting bolts to 45 lbs. 5. Attach the pitman arm to the steering box. Before this is done the steering sector must be centered. Turn the input shaft clockwise as far as it can go. Make a reference mark. Now turn the shaft counter clockwise as far it can go and be sure to count the turns. Turn the shaft back half the distance and now the box is centered. Be sure to double and triple check this procedure. Attach the pitman arm to the output shaft with the output shaft nut. Torque the bolt down to 110ft/lbs. Reconnect the stock drag link and you are on your wa

TOYOTA TACOMA BODY LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 22-09-2011

download
Disconnect both battery cables. Be sure to disconnect the negative cable first, then the positive cable. Remove
the airbag fuse from the fuse box. 4. Remove the wire loom that runs from under the alternator to the battery from the mounting brackets. One bracket is on top of the frame. The other bracket is on the fender well. The plastic mounting-collar will slide off the bracket by pushing on the tab on the collar. 5. Remove the fuse that controls the air bag system from the fuse box (refer to the owners manual for the exact location). 6. Remove the ground wire that runs from the back of the engine to the top of the firewall. Remove the wire loom from the mounting bracket on the firewall. Remove the bracket from the firewall. Turn the bracket upside down. Insert the mounting bolt through the ground wire removed from the firewall, Then through the bracket. Tighten securely. Reinstall the bolt that mounted the ground wire to the firewall. Tighten the bolt securely. Do not attach the wire loom at this time

HARLEY DAVIDSON CUSTOM TOURING FRONT BULLET TURN SIGNAL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION Outer Fairing/Windshield and Auxiliary Lamp Bracket Removal To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2 3 1 2 is 01215 1. Six-position connector 2. Four-position connector 3. Auxiliary lamp connector Figure 1. Disconnect Signal and Auxiliary Lamp 1. Remove Maxi-Fuse. Refer to SYSTEM FUSES, MAXI- FUSE in Service Manual. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 2. Remove the windshield and outer fairing. Refer to UPPER FAIRING/WINDSHIELD in Service Manual for the outer fairing/windshield removal procedure. 3. Disconnect auxiliary lamp and turn signal connectors. NOTE See Figure 1. On 2005 and prior year models, the left and right turn signals plug into a 6-place connector located on the left fairing support brace. On 2006 and later models, each turn signal plugs into its own 4-place connector located toward the bottom of the inner fairing on each side. 4. Using a T40 Torx® drive head, remove and save the four bolts securing the auxiliary head lamp bracket to the chassis. 5. Remove auxiliary lamp bracket from motorcycle. Turn Signal Assembly 1 is 01217 1. Triangular opening Figure 2. Insertion of Terminals Through Triangular Opening 1. See Figure 2. Insert wire terminals through the triangular opening in the turn signal mounting bracket included in the kit. 2. Fit turn signal housing onto bracket. 3. Apply a small amount of Loctite (243) blue (99642-97) to threads of hex head cap screw. 4. Tighten cap screw to 15-20 ft-lbs (20-27 Nm) . -J03753 1 of 2 Turn Signal Installation 1 is 01218 1. Turn signal wire Figure 3. Turn Signal Wire Routing 1. See Figure 3. Insert turn signal connector and wiring between bottom of fairing and top of outer fairing skirt. 2. Route turn signal wire under cutout on mounting bracket and place bracket onto motorcycle. NOTE Care must be taken so the turn signal wire is not pinched between turn signal bracket and motorcycle chassis. 3. Install washers onto turn signal bracket mounting bolts and apply Loctite 243 (blue) (99642-97) to the bolt threads. 4. Tighten mounting bolts to 15-20 ft-lbs (20-27 Nm) . 5. Route turn signal leads toward harness connector. Secure loose wiring with tie straps so wires do not rub against any sharp objects

HARLEY DAVIDSON SOFTAIL LEFT SIDE LEATHER TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Installation While handling and installing tool box, be careful not to scratch surface. 1. See Service Parts Illustration. Install tool box (1) to mounting bracket (6) using button head screws (2) and washers (5). Screws (2) should be inserted through mounting holes on inside of tool box (1) and then inserted through bracket (6) holes and threaded into weld nuts attached to bracket. 2. Remove and save the two screws that secure left rear fender support to motorcycle frame. 3. Remove two bolts, nuts, and washers that secure debris deflector to motorcycle frame. This will allow you to move debris deflector out of the way when installing new passenger footpeg support bolt. Save hardware for reinstallation. 4. For 1990 to 1999 Softails: If tool box is being installed with passenger footpeg, remove the hex head bolt and left passenger footpeg. Retain footpeg and lockwasher for reinstallation. Discard bolt . If tool box is being installed without passenger footpeg, remove hex head bolt and left passenger footpeg. Discard footpeg. Retain bolt and lockwasher. For 2000 and later Softails: See page 3 . Remove footrest from clevis. Remove clevis from frame by removing cap screw from center of clevis. If tool box is installed with footpegs, keep all hardware. If toolbox is to be installed with footboards, discard hardware. 5. Slide top of mounting bracket (6) between rear fender support and frame. Align top holes in bracket with fender support holes. Align lower bracket hole with footpeg mounting hole in frame. Install the two screws, removed in Step 2, in fender support. Do not tighten screws at this time. 6. For 1990 to 1999 Softails: Place lockwasher retained in step 4 on footpeg support hex head bolt (3) from kit. CAUTION 1 of 3 For 2000 and later Softails with footpegs: Install kit 49352-00 according to instructions included in this kit. Footpeg must fold up at a 45°angle (from vertical) toward rear of motorcycle. This angle allows footpeg to fold up if, by accident, it strikes the ground surface when making a sharp turn. Failure to set footpeg to the proper fold-up angle could result in death or serious injury. 7. For 1990 to 1999 Softails: Position footpeg so it folds up and back at a 45°angle. Install bolt (3) from kit through frame, tool box bracket (6), and spacer (4), into footpeg, as shown. NOTE If vehicle is equipped with saddlebag support bracket, Part No. 90346-90 or 90346-94, position saddlebag support bracket between tool box bracket and spacer.

Incoming search terms: