Kawasaki Teryx Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figures 1 Below – place UTV Roof Mounting Brackets on Roof and using a marker, mark the position of the holes needed for each Roof Mounting bracket . For rear of roof mounting, use existing slotted bracket and mark one hole through the factory slotted brackets as shown in Figure 2. Figure 1
Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 Figure 2 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in between holes to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figure 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 3. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Kawasaki Teryx 750 Cab Enclosure Kit Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove seats and set aside for better access to vehicle interior. Refer to Owner’s Manual for instructions. ii) Remove lower foot guardrails and set shoulder screws aside for later use. Loosen 19mm bolts ( A in Fig.1) until 3/16″ gap can be achieved. iii) Loosely fasten rubber stops ( B in Fig.1) to Hinge Mounting Brackets using 6mm bolts. Mount brackets to vehicle as shown in Fig.1 and hand tighten 19mm bolts. iv) Align lower bracket hole to existing foot guard mounting hole and fasten with OEM shoulder screw ( C in Fig.1). NOTE : Apply pressure to screwdriver in order catch threads on nuts. v) Adjust upper edge of brackets with mallet to make bracket edge flush to roll bar edge (Fig.2). Tighten 19mm bolts. Adjust and tighten rubber mounts. FLUSH A B Fig.2 Fig.1 2. Rear Bracketery i) Remove 14mm bolts from lower mounting points on rear crossbar. Install Striker Mounting Brackets as shown (Fig.3). Reinstall bolts and hand tighten only . Attach Striker Plates using (4) ¼-20 x 3/8″ screws, keep loose for later adjustment. ii) Remove 14mm bolts from upper crossbar and install Upper Rear Panel Brackets as shown (Fig.4). Tighten 14mm bolts back into place. 3. Panel Installation i) Install low density foam to interior of panels as shown (Fig.5.) Approx. (8) 3″ long strip are required on each side panel. Install low density foam to entire door / panel interface. ii) Mount side panels to roll cage and temporarily clamp to top roll bar. Loosely insert remaining (2) shoulder screws to each foot well. Adjust each panel to obtain proper alignment at front, top and lower rear. iii) Ensure hinge mounting bracket edges are flush with inside door frame and transfer hinge bolt hole locations onto plastic panels. Remove panels and drill holes using ¼” bit. Re-install panels and shoulder screws onto vehicle. iv) Mount hinges as shown (Fig.6) with (8) ¼-20 x 5/8″ Lg. Flat Head screws. DO NOT OVER TIGHTEN

Kawasaki VN2000 Passenger Floorboards/ Passenger Longboards Installation And Adjustment

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Fasten floorboard assembly to mounting bracket using supplied 3/8″ x 3/4″ bolt, flat washer and lockwasher. Do not tighten at this time (Baron recommends the use of blue Loctite on this bolt). 2. Set floorboard angle by installing flathead allen adjusting screw in the pivot bracket at the desired angle hole. Baron floorboards set to a 15-degree position has been found to be most comfortable and user friendly. Tighten flathead screw. Adjust side tilt angle by moving floorboard stop screw in or out to achieve desired angle. 3. Now fully tighten the 3/8″ bolt. Floorboard is ready for installation. Installation 1. Remove the nuts that attach your stock passenger peg mounting brackets to the frame and remove stock pegs. 2. Install your new Baron floorboards in the same location using supplied M8 mounting bolts and washers. Be sure you dont over-tighten these bolts. It is best to use Loctite when mounting. Adjustment of Floorboard Angle After Installation 1. Using a 9/16″ wrench, slightly loosen the 3/8″ bracket bolt located on the backside of the mounting bracket the floorboard is attached to. 2. Remove the small allen screw located on visible side of the cam bracket. Once this screw is removed, adjust the cam to the desired hole and insert and tighten allen screw. 3. Re-tighten 3/8″ bolt. Repeat process on both sides. NOTE: All adjustments may not be available with all exhaust systems