HARLEY DAVIDSON FLSTS MUD FLAP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
Installation For installation on rear fender with marker light: 1. Cut out Rear Fender Template. 2. Use a paper punch to punch out holes marked A and C . Holes A are the locations of the marker light screws, and hole C is the location of the marker light wiring. Cut along centerline of template from top down to hole C . 3. Remove light lens by carefully pressing down on top center of light to disengage tab. 4. Remove the two screws, washers, and nuts that hold the marker light assembly in place and carefully pull the light assembly away from the fender. Disconnect the wire connector and remove the light assembly. 5. Slip template over marker light wires, align holes marked A with marker light holes, and align lower edge of template with lower edge of fender. Tape template in place. 6. Prick punch holes marked B at indicated centers on template. 7. Carefully, and as accurately as possible, drill holes marked B in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 8. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure outer holes with buttonhead screws (3), washers (6), and locknuts (7) contained in kit. The mud flap is split to fit around light assembly wires. 9. Using the longer panhead screws provided in the kit, install fender tip light and check that light is operational. For installation on rear fender without marker light: 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Rear Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes marked B and C at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked B and C in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit. For installation on front fender (FLSTS only): 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Front Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

Incoming search terms: