2006-2010 Triumph Sprint St 1050 Exhaust System Installation Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on center stand or ideally a service lift. 2. Remove the seat and handle: 3. Remove the rear cowling: 4. Remove the fender assembly: 5. Remove the plastic cover on fender assembly to expose the brake and turn signal wires. Disconnect the brake light wires: 6. Remove the OEM muffler: 7. To install the Two Brothers Racing Slip-on Exhaust System: Attach the slip-tube with the X-Lite Ring™ to the muffler using the 4 (four) 6x14mm socket head cap screws and split lock washers provided. Leave loose for now. 8. Attach the rubber lined muffler clamps and plate brackets as shown to the muffler assembly using the 2 (two) 8x20mm socket head cap screws and nuts provided. Leave loose for now. 9. Install muffler assembly using the OEM mounting bolts and joint clamp. 10. Make sure muffler is aligned when the bike is centered. Then tighten the four V.A.L.E.™ assembly bolts and clamp bolts. Make sure there is clearance between wiring and all body parts. 11. Attach the turn signals/taillights and plate lights as shown in Wiring Diagram. Join wires to main wire harness using the supplied splice connectors and blue scotch locks. You can either cut the OEM modular connectors off of the wiring harness or splice new wire to them. The supplied lighting devices will need to have the modular connectors removed. Run all wiring to the left side of the rear frame, away from the muffler assembly making sure there is adequate clearance from all body parts. Make sure all lights work correctly. 12. Re-install the fender assembly, rear cowling, seat and handle from steps 2-4. 13. Double check your work for alignment and fitment. 14. Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Remove any plastic film from name badge(s) and/or canister clamp(s). Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness

Aprilia Mille And Mille R Exhaust System Installation Instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the sidestand or ideally a service lift. 2. Unhook the springs holds the stock canister to the headers under the bike. 3. Remove the hardware that holds the stock canister at the exhaust bracket. Take off the stock canister. 4. Install the new s-bend into the stock header. 5. Install VALE adapter kit using supplied kit instructions. 6. Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 7. Carefully slide the muffler clamp over the muffler. (Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need to twist and turn the S-bend a little to get it in the right place. Locate both tabs of the canister clamp on the outside of the exhaust bracket. Use the stock hardware to secure it. Leave loose for now. 8. Make sure everything is aligned and tighten all hardware. Reinstall the stock springs at the s-bend/header junction. Affix the two connector springs to the muffler. 9. Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness