KAWASAKI TERYX EFI Installation Instructions.

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
Basic Tuning Adjustments 1. The following instructions are for basic fuel tuning. Modes 1,2, & 3 are allowing adjustments to increase and decrease the amount of fuel the engine needs. Modes 4 & 5 are for advanced tuning only. DO NOT change modes 4 & 5 when doing basic tuning! 2. To help understand how these modes work, you can think of them as if you were working with a carburetor. 3. Remember each time you push the MODE button you will be advancing to the next mode. Push the MODE button once and you are now in mode 1, push the MODE button again and you are now in mode 2 and so on. You only need to be concerned with modes 1, 2 & 3 for basic tuning. Modes 4 & 5 are for advanced tuning ONLY. 4. If you need to go back to the settings that were pre programmed when you purchased the controller, just look at the picture in each mode, the colored square represents where the settings were when you purchased the controller. 5. Looking at the controller you will see eight lights with numbers under them, this is what you need to look at when changing settings. The #1 light on the controller represents the leanest setting. TRINITY RACING DOES NOT TAKE REPONSIBLITY FOR DAMAGES THAT MAY OCCUR DURING OPERATION OF YOUR VEHICLE UNDER IMPROPER JET SETTINGS. IT IS THE FINAL RESPONSIBLITY OF THE OWNER/RIDER TO ADJUST JETTING TO SPECIFIC RIDING CONDITIONS AND ELEVATION BEFORE RIDING. WARNING! 1.877.FAS TOYS 2.Remove both seats 6. Re-install engine cover and seats. 6. Mode 1 green light represents idle & cruise adjustment (i.e. pilot jet). To adjust this setting push the MODE button once and then push the plus or minus buttons to adjust fuel as needed. 7. Mode 2 yellow light represents an additional amount of fuel added during acceleration (i.e. needle position). To adjust this setting, push MODE twice and then push the plus or minus buttons to adjust fuel as needed. 12 34 56 7 8 12 34 56 7 8 8. Mode 3 red light represents more fuel being added during full throttle (i.e. main jet). To adjust this setting push the MODE button three times and then push the plus or minus buttons to adjust fuel as needed. 9. If you are confident about your tuning skills and feel you need to adjust other parameters, see Advanced Tuning. 12 34 56 7 8 Advanced Tuning Adjustments 1. Advance tuning has two modes in which to adjust. They are called mode 4 and mode 5. In basic tuning, you are changing the amount of fuel that the engine receives, but with advance tuning, you will be changing when the fuel will be available. In each mode you can adjust how soon the fuel delivery occurs. 2. Mode 4 yellow light and blue light represent when the fuel delivery is available during partial throttle acceleration. To adjust this setting, push the MODE button four times and then push the plus or minus buttons to adjust fuel as needed. Only the yellow light will be changing.

Incoming search terms:

Bridgestone 350 SPECIFICATION AND SERVICE MANUAL

0

Filed Under (Bridgestone) by admin on 03-12-2010

download
Engine ( 1 ) Type : ( 2 ) Piston Displacement : ( 3 ) Bore & Stroke : ( 4 ) Compression Ratio : ( 5 ) Max. Brake Horse Power ( 6 ) Max. Torque : ( 7 ) Air Intake System : ( 8 ) Starting System : ( 9 ) Charging System : (10) Ignition System: (11) Ignition Timing: (12) Spark Plug: (13) Carburetor: (14) Engine Lubrication: (15) Fuel: (16) Transmission Oil: Performance ( 1 ) Max. Speed : ( 2 ) Climbing Ability : ( 3 ) Fuel Consumption : ( 4 ) Min. Turning Radius : ( 5 ) Acceleration : (Standing Start 1/4 mile) (Zero to 60 mph) : ( 6 ) Braking Distance : Frame and Suspension (1) Frame: (2) Front Suspension: (3) Rear Suspension: 2-stroke, Dual Cylinders 344.9cc (21.5 cu-inches) 61 mm × 59 mm (2.40 × 2.32 inches) 9.31:1 40 HP/7500 rpm 4.0 kg-m/7000 rpm Rotary disc valve Kick Starter A. C. Generator Contact breaker gap : 0.3 – 0.4 mm (0.012 – 0.016 inches) Battery (25+1-2) degrees before T.D.C. N.G.K. B-8H, Electrode gap : 0.6 mm (0.024 inches) Type AMAL VM 26 SC Venturi: 26 mm Main Jet No.: 130 Throttle Valve Cut Away: 2.0 Air Jet : 2.0 Adjustment of Needle Jet : 0.6 Pilot Jet: 22.5Pilot Air Screw Position: 2 turns out Needle Position: 3 2 cycle oil Regular Gasoline 1.5 liter (2/5 US gal.) in transmission case SAE No. 10W/30 in all seasons or SAE No. 30 in summer and SAE No. 20 in winter 100-110 mph 1 in 2 94 mpg/25 mph (40 km/litre at 40 km/h) 2.25 m (7.38 feet) 13.7 sec 5.2 sec (Less than 12m at 50 km/h) 39 feet, at 30 mph Pipe Frame, Cradle Type Telescopic Fork with Hydraulic Damper Swinging Arm with Hydraulic Damper
Technical Data 2 Transmission ( 1 ) Clutch : ( 2 ) Transmission : ( 3 ) Gear Ratio : Dimensions and Weight ( 1 ) Overall Length : ( 2 ) Overall Width : ( 3 ) Overall Height: ( 4 ) Saddle Height : ( 5 ) Wheelbase: ( 6 ) Road Clearance : ( 7 ) Tire Size (Front) : (Rear): ( 8 ) Tire Pressure (Front) : (Rear): ( 9 ) Caster : (10) Trail: (11) Banking Angle: (12) Net Weight: (13) Fuel Tank Capacity: (14) Oil Tank Capacity : Electrical Equipment ( 1 ) Head Light : ( 2 ) Tail Light : ( 3 ) Stop Light : ( 4 ) Speedometer Lamp : ( 5 ) Tachometer Lamp : ( 6 ) Neutral Indicator Lamp : ( 7 ) 5th Gear Indicator Lamp : ( 8 ) Headlight High Beam Lamp : ( 9 ) Battery : Manual, Multiple discs, Dry type Constant mesh 6-speeds Primary (Helical Gear) 1:3.095 Gear Box: 1st 1:2.46 2nd 1:1.647 3rd 1:1.25 4th 1:1.00 5th 1:0.852 6th 1:0.759 Secondary (Chain) : 1:2.40 Total Gear Ratio : 1st 1:18.27 2nd 1:12.23 3rd 1:9.29 4th 1:7.43 5th 1:6.33 6th 1:5.64 2,110 mm (83.1 inches) 825mm (32.5 inches) 1,115 mm (43.9 inches) 810mm (31.9 inches) 1,375 mm (54.1 inches) 145 mm (5.7 inches) 3.25-19 4 ply 3.25-19 4 ply 2.0kg/cm2 (28-30 lbs/in2) 2.2 kg/cm2 (30-32 lbs/in2 ) 63° 105 mm (4.15 inches) 46° 165 kg (363 lbs) 15 litre (3-4/5 US gal.) Including 3.2 litre (4/5 US gal.) reserve 2.5 litre (3/5 US gal.) 12V-35/30W 12V-7W 12V-23W 12V-3W 12V-3W 12V-3W

Incoming search terms: