HARLEY DAVIDSON TIMER COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) NOTE For kits 32972-04A, 32924-04A, 32675-04A, and 32923-04A, refer to step 1 and 2 for installation instructions. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. See Figure 2. Remove and discard the original screws and timer cover. 2. Place new timer cover (1) in position and secure with chrome screws (2). NOTE For kits 32584-88TA, 32668-98A, and 32571-98A, refer to steps 3 through 8. 3. Use a 3/8 in. drill bit and drill the heads off the original timer cover rivets. Remove original timer cover. NOTE If the inner timer cover has been riveted in place and access to the cam position sensor is required, use a left hand drill and carefully remove the rivet heads. If a right hand drill is used, the sensor plate screw heads could break off when trying to remove the rivet. NOTE To make the cam position sensor tamper proof, follow steps 4 through 6. If the cam position sensor is not required to be tamper proof, skip steps 4 through 6. 4. Remove and discard inner cover retaining screws. Leave gasket (if used) and inner cover in position. 5. See Figure 1. Place washers (4) over rivets (3) and place rivets into inner cover holes so the backs of the rivets go into the sensor plate screws’ tapped holes. 6. Use a standard rivet tool and install rivets, securing inner cover to sensor plate screws. 7. Use the self-tapping screw (5) to cut threads into the remaining inner cover holes. Discard screw after use. 8. Place new timer cover (1) in position over inner cover (A) and secure with chrome screws (2). NOTE For kit 32581-90TB, refer to steps 9 and 10. 9. Use 3/8 in. drill bit and drill the heads off the timer cover rivets. Remove original timer cover. 10. Place new timer cover in position and secure with chrome screws (Part Number 9462) from kit

HARLEY DAVIDSON STREET SLAMMER HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
This kit does not fit models equipped with Hydraulic Clutch Kits, handlebar mounted gauges or the Road Tech® Radio or FLHRS models equipped with an accessory windshield. REMOVAL Preparation – All Models To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Save the seat hardware for installation. -J04406 When servicing the fuel system, do not smoke or allo w open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Softail and Dyna models: See the service manual and loosen the fuel tank. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled DOT 4 brake fluid. 3. See the service manual and drain the brake fluid from the front brake reservoir and brake lines. Handlebar Removal – Dyna and Softail NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 1. Note the front brake line routing and the orientation of the banjo fittings. See the service manual and disconnect and remove the brake line. Save the banjo bolts, but discard the brake line gaskets. 2. Remove the plastic wiring retainer clips that secure the turn signal harnesses to the handlebar, if equipped. 3. Remove the front brake master cylinder and clutch lever assemblies from the handlebar.

HARLEY DAVIDSON SOFTAIL TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. 2. Raise the motorcycle on a floor jack to lower the rear wheel for fender hardware access. 3. See Figure 1. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 1. Remove Tail Lamp Lens 4. See Figure 2. Using a Terminal Pick Tool (1), press locking tabs and disconnect turn signal connectors (2-place, Items 2 and 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. NOTE FXST/S/B tail lamp and connectors are positioned 180° from orientation shown in Figure 2. 6. Reach under fender to locate clips fastening turn signal wires in place. Carefully pull wires out of clips, and pull turn signal connectors and wires out from under fender. a. Remove two-inch (51 mm) section of conduit 4 inches (102 mm) from turn signal connectors. b. Cut black turn signal wire about 5-1/2 inches (140 mm) from its connector. c. Cut violet/brown turn signal wire about 4-1/2 inches (114 mm) from its connector. d. Save cut wires with respective turn signal connectors. 7. Remove the sissy bar and/or sideplate assembly, if equipped

HARLEY DAVIDSON SMOKED AND CLEAR FENDER TIP LENS KITS Preparation MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery cables, negative cable first. 2 . See Figure 1. Insert blade of small screwdriver into slot at top of front fender tip lamp lens (2). Rotate end of screwdriver to unsnap lens from lamp bracket. Repeat for rear fender tip lamp lens. 3. Remove bulb (3) from socket (4). 4. From the kit, find the LED marked “Amber” (5) and install into front fender tip lamp assembly.lamp socket. 5. From the kit, find the LED marked “Red” (5) and install into rear fender tip lamp assembly.lamp socket. Always connect the positive battery cable first. If the positive cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 6. Connect the battery cables, positive cable first. 7. Apply power and check for proper function of front and rear fender tip lamps

HARLEY DAVIDSON HORN COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat and disconnect wires from horn. 2. See Figure 1. Remove stock horn bracket nut (2) and the entire stock horn cover assembly (1). Remove the horn (3) and all hardware components from the stock cover including wire clamp, clips, and mounting bracket. Leave rubber mount and locknut on motorcycle. Note assembly order for kit installation. NOTE Do not over-tighten “horn to horn cover” nut. Over-tightening may result in permanent damage to the horn. 3. Apply Loctite 271 (Red) to threads of nut (4) fastening the horn to the horn cover. Tighten nut to 80-100 in-lbs (9.0- 11.3 Nm). Tighten screws fastening the horn cover to the horn bracket to 35-55 in-lbs (4.0-6.2 Nm). 4. Route wiring harness through the clamp (if present) and install the entire horn cover assembly to the mounting stud (5). 5. Tighten nut (2) fastening the horn bracket to the horn rubber mount to 80-100 in-lbs (9.0-11.3 Nm). Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 6. Connect wires to terminals and reconnect battery. NOTE Horn is not polarity sensitive. Ground and power wire may be connected to either terminal. 2 4 1 5 3 is03958 1. Horn cover assembly 2. Bracket nut 3. Horn 4. Nut 5. Mounting stud Figure 1. Horn Cover Installation 7. Test horn. NOTE Test the horn only when mounted on the vehicle. The sound may be muffled if tested when hand-held. A muffled sounding horn that is mounted to a vehicle may indicate permanent damage to the horn by over-tightening the horn to horn cover nut (Figure 1, Item 4). Attempt to adjust nut torque. Replace horn if necessary. 8. Reinstall seat

Incoming search terms:

HARLEY DAVIDSON AUXILIARY BRAKE/ RUN/ TURN SIGNAL CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) -J03990 Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 2. See Figure 1. Locate the rear wiring harness coming out of the rear fender in the area underneath the seat. Disconnect the rear fender lighting wiring connector (1) from the main harness connector (2). 3. Obtain the turn signal module from the kit, and mate the module connectors to the male and female rear fender wiring harness connections. Snap into place. NOTE Due to variations between models, there is no single best location to secure the module. When deciding on a location for securing the module, make sure that the connectors and module will not be bound, and that the wiring will not be pinched when the seat is re-installed. Also, be certain to maintain clearance between the wiring harness and the rear wheel underneath the fender. 4. Using cable straps from the kit, secure the module, connector and wiring in the area underneath seat. 1997-1999 FLHR and FLHRCI models: Go to Step 5. All other models: Proceed to Step 6.

HARLEY DAVIDSON CHROME DISPLAY STAND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and disconnect the battery negative (-) cable or remove the main fuse. NOTE Make sure that the cutout (B) of the strap (3) is oriented to the rear of the motorcycle after installation. 2. See Figure 2. Install strap (3) and weld nut (4) to the frame in the locations shown. 3. Position the center display stand over the mounting holes under the frame, oriented so that the skid plate faces for- ward. 4. Apply a small amount of Loctite 271 – Red to the two long screws (1) and secure the rear of the display stand to the frame by installing the two screw to the strap. 5. Apply a small amount of Loctite 271 – Red to the short screw (2) and secure the front of the display stand to the frame by installing the screw to the weld nut. 6. Tighten screws to 60-96 in-lbs (7-11 Nm) . 7. Refer to the service manual and connect the battery cables or install the main fuse. 1 2 is05370 1. Flange side 2. Flat side Figure 1. Chrome Display Stand Foot Orientation ADJUSTING THE DISPLAY STAND The left and right feet of the display stand are independently adjustable to vertically level the vehicle with the display stand extended. To adjust the display stand: NOTE The display stand can be adjusted with rear tire to ground contact or with rear tire off the ground. With the rear tire to ground contact adjustment, the rear wheel is on the ground but enough weight is on the display stand legs to make the motorcycle stable from side-to-side and front-to-back. Using the display stand to center the motorcycle will require effort. With the rear tire off the ground adjustment, the rear tire clears the ground so tire can be rotated for cleaning or maintenance purposes. Using the display stand to lift rear tire off the ground will require more effort. Do not center the vehicle with someone on the vehicle. To reduce effort, remove stored items from saddlebags, if equipped

Incoming search terms:

HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms:

HARLEY DAVIDSON COMBINATION SPEEDOMETER/ TACHOMETER GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
REMOVING THE OLD SPEEDOMETER NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Make sure you locate and follow the procedures that apply to the motorcycle receiving the new gauge. 1. Apply power to motorcycle and record the odometer reading. 2. Remove the seat according to the procedure in the applicable Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 3. Disconnect battery cables, negative cable first. NOTE Cover the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 4. Remove the instrument console acorn nut (and mounting screw with a flat washer on some models). Lay clean shop towels on the fuel tank. Lift the console from the fuel tank, turn it upside down and lay it on the towels. NOTE If necessary, bend back the flexible metal clip to free the harness conduit from the underside of the console. 5. Unplug the 12-terminal connector [39B] from the back of the speedometer. Depress the external latches and use a rocking motion to separate the pin and socket halves. 6. Remove the back clamp. All models except FXSTD: Gently pry the three latches upward to release the back clamp from the back of the speedometer. FXSTD: Depress the three external legs of the lock ring, then gently pry the three latches upward to release the back clamp from the back of the speedometer. 7. Unscrew the trip-meter reset button, and pull the harness from the clamp (remove the screw if necessary). 8. Lift the console and remove the old speedometer from the console. Discard the old speedometer, but retain the rubber gasket and back clamp for use with the new gauge. NOTE Set the console securely on the towel-covered fuel tank, and take care that it does not fall off during the following operations. 9. Set the console securely on the fuel tank

HARLEY DAVIDSON SPORTSTER® ACCESSORY SLIP-ON MUFFLER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Remove mufflers using appropriate Service Manual instructions. 3. Discard gaskets and mufflers. 4. Install new gaskets on mufflers. 5. Slip muffler clamps on mufflers. 6. Loosely attach mufflers to the interconnect tube using existing screws and washers. 7. Position the ends of the front and rear exhaust pipes into front and rear cylinder heads and align exhaust system while tightening all nuts and bolts; begin at the cylinder head exhaust ports and work back toward the mufflers. a. Finger tighten the upper nuts to the mounting studs. b. Tighten the lower nut to 9-18 in-lbs (1.0-2.1 Nm) . c. Tighten the upper nut to 60-80 in-lbs (6.8-9.0 Nm) . d. Tighten the lower nut to 60-80 in-lbs (6.8-9.0 Nm) . 8. Tighten the acorn nut on the rear exhaust pipe support clamp to 15-19 ft-lbs (20.3-25.8 Nm) . 9. Tighten muffler clamps to 45-60 ft-lbs (61-81.3 Nm) . 10. Tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm)