1997-1998 EFI Harley Davidson 1340 EVO Power Commander Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-03-2012

download
1 Remove the seat. 2 Remove saddlebags if installed. 3 Remove left and right side covers. 4 Remove the battery (negative terminal first). 5 Loosen the two 7/16 nuts that retain the ECU (Fig. A) 6 From the left side (underneath the left side cover area) feed the PC III connectors in front of battery tray, and out the right side (in front of the ECU bracket)(Fig. B). 7 Attach PC II module to battery box. First, clean the PCIII and battery box with the supplied alcohol wipe. Using the supplied velcro attach PCIII to the battery box. Also secure the unit with the included zip ties. If your bike has cruise control, attach the unit to the face of the cruise control module (Fig. C). 8 Disconnect the large connector from the ECU. Remove the rubber dust shield. 9 Install the dust shield onto the matching connector on the PCIII. Zip tie the rubber dust shield to the PCIII connector with zip tie provided. 10 Plug the PCIII connector into the stock ECU. 11 Plug stock connector into the remaining connector from the PCIII (Fig. D). 12 Tighten the two 7/16 nuts that retain the ECU. 13 Route the connectors alongside the ECU and install the right side cover. 14 Replace the battery, the left side cover and the seat. 8 5 Power Commander Connnector Stock Connnector Fig.D Fig.E Adjust Idle Speed here Fig.F Adjusting Your Power Commander Your Power Commander has been programmed with a base map for your application. You can adjust the base map or install an alternate map using your Computer. Please refer to the supplied CD-Rom for more information. You can also adjust your Power Commander using the face plate buttons as described below. 1. With the ignition off, hold down all three buttons on the Power Commander unit. 2. While still holding down the buttons, turn the ignition on. 3. Release buttons

Incoming search terms:

Harley Davidson Touring Bikes TRUMPET INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2012

download
COMPRESSOR INSTALLATION TOUR MODELS 1992 -2000 On the Dressers and Tour bikes, remove the seat. If the battery is located underneath the seat, then remove the right saddlebag and right hand side cover. Using a zip tie, mount the compressor to the main wiring harness at the front of the covered area with the compressor air outlet facing down. If the battery is not under the seat and is located beside the right saddlebag, the compressor will be mounted underneath the seat, utilizing a bolt to the frame The air hose routes from the air horns, behind the fuel valve, over the rear cylinder and to the right side cover or underneath the seat. Do not cut hose until you connect it to the compressor. TOUR MODELS 2001 & NEWER On the Dressers and Tour bikes, the compressor will mount under the seat, in the square hole in front of the frame, just in front of the battery. The air output will face left toward the air horns. The hose routes thru a hole at the bottom of the square hole, then to the air horns. WIRING Connect both black wires from the relay to the original horn wires. It does not matter which wire you connect. The fuse wire on the relay will connect to the positive terminal on the battery. Observe negative and positive terminals on compressor. Ground the negative terminal to the battery. The positive terminal connects to red wire on relay. Refer to wiring schematic on the next page

Incoming search terms:

Suzuki GSX-R 1000 AFR Tuner INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 20-02-2012

download
The installation of the AFR Tuner should be done by experienced technicians only. Always disconnect the battery from the motorcycle before making any modification to the wiring harness. Remove the negative terminal from the battery before starting the installation work. The quality of the installation work greatly affects the reliability of the AFR Tuner and the motorcycle. Work precisely and very carefully when modifying the wiring harness of the vehicle. Always double check that the wire you are about to cut or tap into is the correct one. The ECM or the AFR Tuner can be destroyed by a faulty installation. 3.2. Installing the AFR Tuner to the wiring harness 3.2.1. Main cable The AFR Tuner connects to the motorcycle through its Main connector . Figure 2 shows the wiring diagram and the necessary modifications, which needs to be made when installing the unit into the fuel injection system of the motorcycle. Information about the ECM terminal numbers and wire colors for some popular motorcycles can be found in Chapter 6 . The best location for installing the AFR Tuner main unit is at the passenger seat area of the motorcycle mounted in the trunk space or on the subframe under the fairing, as this place provides protection from engine heat and the weather. Electrical contact between the metal casing of the AFR Tuner and the rear subframe must be prevented by using insulating material, such as the included self adhesive velcro strips. If necessary use some cable ties to secure the unit in place. The installation of the AFR Tuner into the wiring harness involves tapping into some wires and cutting others while connecting the two ends to the AFR Tuner. The harness modifications are best done near the ECM, since most of the wires can be found there. Part of the wiring modifications are related to connecting the AFR Tuner in-line between the ECM and the fuel injectors. In such cases when the motorcycle is equipped with primary and secondary injectors the AFR Tuner has to be installed on the primary injectors, which operate under all engine conditions. Correct grounding of the AFR Tuner is very important for electrical noise reduction. The above mentioned insulation of the metal case from the motorcycle frame is necessary for the same reason, which is to avoid the forming of a ground loop. An even more important requirement is the correct connection of the three ground wires of the AFR Tuner. As shown on Figure 2 , these three wires must be led out separately to the ECM and connected together at same point where the ECM ground wire is tapped into. This point should be as close to the ECM terminal as possible. For best quality of the electrical contacts all connections should be done by soldering and covering the exposed part of the wire with heat shrink tubing. For reliability reasons do not use clip on type wire taps

Incoming search terms:

Yamaha TDM 900 Disconnecting the battery ground REMOVAL AND INSTALLATION

0

Filed Under (Yamaha) by admin on 29-01-2012

download
Remove the seat. • Disconnect the battery ground (negative terminal). Remove the fairing side panels. • Remove the four marked hex screws with plastic washers. Note the positions the screws come from as they are not all the same. • Note that the bottom, rear hex bolt has a retaining plastic washer INSIDE the fairing. The long bolt goes under the ‘twin’ label. • Remove the hex screw indicated on the inside of the fairing panel. • Remove the grey Phillip’s head screw as indicated on the inside panel. • Remove the plastic locking clip on the underside of the fairing behind the radiator.

Incoming search terms:

GL 1200 CB TRANSCEIVER Installation Manual

0

Filed Under (Honda) by admin on 21-11-2011

download
Remove the right and left side covers. Disconnect the battery negative cable from the battery negative terminal.
2) Remove the left fairing pocket Remove the Auto volume control unit. -1 Remove the CB blind cover from the fairing by removing the four 5 x 22 mm socket head bolts. (Fig. 2) Disconnect the three wire connectors of the auto volume unit. (Fig. 3) -2 Remove the two 4 x 12mm tapping screws and remove the knob and nut from the auto volume control unit. (Fig. 1) -3 Remove the bracket form the auto volume control unit. NOTE: Discard the CB blind cover, 4 x 22mm tapping screws, and bracket. 4) Remove the seat. 5) Remove the shelter NOTE: To remove the front of the shelter, it is necessary to remove the inner cover by lifting the rear of the cover. 6) Remove the two tapping screws attaching the left coupler cover and move the holder towards the center. 7) Remove the main amplifier. -1 Disconnect the main amplifier 2-P black connector. -2 Straighten the four wire clamps at the main amplifier to release the harnesses. -3 Remove the two nuts and washers holding the main amplifier; pull the amplifier out between the left fairing pocket and handlebar by pulling up on the bottom. 8) Connect the two DIN connectors if the transceiver harness (65) to the terminal component (62) color-to-color (Fig. 7). 9) Remove the seals from the terminal component mounts inside the fairing. Position the terminal component (62) on the mounts and install using cap nuts (69) and washers (72). NOTE: Use care when installing the terminal component (62) not to push in the audio harness, CB harness and terminal component harness into the fairing pocket

HONDA GL1800 CB RADIO KIT INSTALLATION And REMOVAL

0

Filed Under (Honda) by admin on 20-11-2011

download
These instructions are for installation of the CB radio. For operation of the CB radio, refer to the Owner’s Manual and FCC Rule Book furnished with the CB radio. • Install the antenna which is sold separately between the installation of the rear trunk and the routing of the wire harness. • It is not necessary to drill four 7 mm holes and install the plate when you are also installing the CD changer. 1. Refer to the Service Manual to remove the right and left side covers and disconnect the negative terminal from the battery

1996 Toyota Supra STARTING & CHARGING SYSTEMS

0

Filed Under (Toyota Manuals) by admin on 16-06-2011

Download
Use a 10mm ratchet attachment to remove the battery from the vehicle. Negative terminal first, then positive. Be careful not to cause an arc between the two terminals as intense pain will result.
Remove the plastic plate that the battery sits in. 2. Using the 10mm attachment again, remove the 6 bolts that hold the passenger side front splash guard from underneath the front bumper
From underneath the vehicle, locate the oil filter. Look above oil filter and you will see the starter. Locate the bottom 14 mm bolt that attaches the lower portion of the starter to the engine. The bolt
drives from left to right. The starter is mounted toward the front of the vehicle and underneath the intake manifold. Still cant find it? Follow the cable that leads from the positive battery terminal. It
ends at the starter. Not sure you have the right bolt? Stick your 14mm attachment on it with your fingers and see if it fits on properly

YAMAHA ROADSTAR TRIKE Removal of Clear Taillights and installation of Red Taillights

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1 Installation of Lights 1.1 Support the trike on jack stands and remove the wheels. 1.2 Remove the clear lights from the inside of the wheel wells by unscrewing the three (3) screws from the light. 1.3 Unplug the wires and remove the lights. 1.4 Remove the chrome bezels and rubber gaskets from the clear lights and install on the red lights (5 screws). 1.5 Re-connect the wire plugs and install the red lights to the trike body using the same three screws. 1.6 Replace the wheels and torque the lug nuts to 75 lb.ft. 2 Wire modification inside trunk 2.1 From the inside of the trunk pull back the carpet on both the left and right hand sides to expose the wire harnesses coming from the wheel wells. 2.2 Locate the resistors in the harness, 2.5″ x 0.5″ x 0.5″, and covered by black shrink wrap. 2.3 Cut the shrink wrap to expose the resistors and cut wire on both side of the resistors. Remove and discard resistors. 2.4 Splice in the supplied 5″ green wires (WITHOUT the diodes) with 2 blue scotchlock connectors per side to reconnect the cut wires. 2.5 Do not glue in carpet until lights are tested. 3 Change to pigtail from Trike to Motorcycle. 3.1 Remove driver’s sear 3.2 Unplug pigtail from motorcycle (MC) wiring and trike body wiring. 3.3 Cut heat shrink on the MC plug side of the pigtail and pull expansion sleeve back to expose the wires. Figure 1 3.4 Cut Green and Yellow turn signal wires and about 3″ from the MC plug and splice in Green and Yellow wires from the supplied resistors with the supplied hest shrink solder connectors (heat to be applied) – (three wires in one connection) Figure 1 3.5 Cut the Red (Brake) and Brown (Running lights) wires and splice in the supplied diodes with the supplied heat shrink solder connectors. Red side of the diode wire facing the Trike plug. Figure 1 3.6 Connect eye lug on the black wire from the resistors to the negative terminal of the battery. Figure 2 3.7 Plug pigtail back into the Trike body and the MC

Incoming search terms:

Baron Tachometer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Some models like Harley-Davidson, Kawasaki Vulcan FI models, Suzuki FI models, Honda VTX 1800 and others may require the included Tach Adapter. See separate instructions for installation of the adaptor. Wiring instructions for 7-Color LED Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire of tach to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire of tach to CHASSIS (Ground) • Red wire to of tach to POSITIVE terminal of coil (or other switched 12 volt source) • Red wire from control box to POSITIVE terminal of coil (or other switched 12 volt source) • Black wire from control box to CHASSIS (ground) • Control box plugs into tach with the 4-way connector • Button plugs into the control box. Button can be mounted on handlebar or any other convenient place Wiring instructions for White- or Black-Face Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire to CHASSIS (Ground) • Red wire to POSITIVE terminal of coil (or other switched 12 volt source) • Blue wire to POSITIVE terminal of coil (or other switched 12 volt source) General mounting instructions (1) Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off- center, you can rotate tach face back to vertical (or any position you desire) by first loosening tach unit’s set screw (found either in handlebar area of housing or underside of housing, depending on tach style), then unscrewing tach housing’s bezel, rotating tach, re-installing bezel and retightening set screw. Secure handlebar clamp by first tightening the rear, flat side of clamp all the way down, then tighten tapered front side of clamp until tach does not rotate. There should be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened. (2) Route tach’s wire harness lead to coil as necessary for simplest and cleanest installation. Feed tach harness alongside bike’s wiring harness (passing behind any plastic frame covers), then downward toward coil. (3) Make your wire connections as recommended above. Use the spade and piggyback connectors

Incoming search terms:

VICTORY HAMMER, KINGPIN, VEGAS AND JACKPOT ELECTRIC HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 29-01-2011

download
1. Remove the left and right plastic side covers and the seat (two allen bolts located below the sides of the seat). Unplug and remove the stock horn (located over the oil cooler). Connect the female ends of the jacketed two wire cable supplied to the original horn wires. Route the other end of the cable up over the engine and back to where the relay will mount as shown in photo (1). 2. Using the relay supplied with this kit and the wiring diagram provided with the horn set, identify the terminals of the relay (there are very small numbers next to each of the terminal). Connect the two (2) wires from the cable to terminals #85 & 86 on the relay. Locate the fuse holder wire assembly supplied and connect the blade terminal to the relay terminal #87 or #30. Connect the other end of the fuse wire to the battery positive terminal (+). 3. Working under the left side of the motorcycle, refer to photo (2) and install the black bracket supplied as shown onto the engine mount. Locate the four thin flat brackets and two (2) 6mm nuts supplied with the horn set and two lock washers supplied with the kit. Bolt two (2) of the brackets to each of the horns using a lock washer and 6mm nut on each and make them snug. Using the remaining 6 x 12mm bolt, nut and lock washer install the horns onto the black bracket and align as shown in photo (3). Adjust the horn location so that they are free to vibrate and do not come in contact with other parts of the motorcycle then tighten all three 6mmm bolts securely. 4. Using the two remaining wire assembles supplied, connect the larger terminals with double wires to one of the horns and the terminals with the single wire to the other horn. Route these wires up thru the frame to the relay. Connect the wire with the female blade connector to the relay terminal #30 or #87. Connect the ring terminal to the battery negative (-) terminal
or any 6m bolt on the frame. Turn on the ignition and test the horns. Secure the relay to the frame or other wiring and all loose wires using the cable ties supplied. Replace the seat and side covers

Incoming search terms:

Incoming search terms: