TOYOTA Engine Intermittent No Crank/ No Start REPAIR

0

Filed Under (Toyota Manuals) by admin on 11-10-2011

download
Some Highlander, Matrix, and RAV4 vehicles may intermittently exhibita”no crank”condition. The engine can usually be started after moving the shift lever to the Neutral position orby cycling the shift lever in and out of the Park position. Are vised neutral starts witch assembly is available to address this condition. Warranty Information OP CODE DESCRIPTION MODEL TIME OFP T1 T2 Highlander 0.9 Matrix 0.5 832131 R&RP ark/Neutral Position Switch Assembly RAV4 0.7 84540-42010 17 99 APPLICABLE WARRANTY •Thisrepairis covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 monthsor36,000 miles, whichever occurs first, from the vehicle’sin-service date. •Warranty application is limited to occurrence of the specified condition described in this bulletin.

YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

YAMAHA FJR1300N OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
3-2 3 EAU03034 Indicator and warning lights EAU04121 Turn signal indicator lights “” a n d “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU00061 Neutral indicator light ” ” This indicator light comes on when the transmission is in the neutral position. EAU00063 High beam indicator light ” ” This indicator light comes on when the high beam of the headlight is switched on. EAU03201 Oil level warning light ” ” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” ” and turn the key to “ON”. 2. Shift the transmission into the neu- tral position or pull the clutch lever. 3. Push the start switch. If the warning light does not come on while push- ing the start switch, have a Yamaha dealer check the electrical circuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function. EAU03192 Engine trouble warning light ” ” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this oc- curs, have the Yamaha dealer check the self-diagnosis system. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” “. 2. Turn the key to “ON”. If the warn- ing light does not come on, have a Yamaha dealer check the

Incoming search terms:

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms:

YAMAHA XT500E, XT600E SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3 ON OFF LOCK . EAU00040 LOCK The steering is locked, and all electrical systems are off. The key can be removed. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. 12 1. Push. 2. Turn.
3-2 INSTRUMENT AND CONTROL FUNCTIONS 3 EAU00056 Indicator lights EAU00063 High beam indicator light ” & ” This indicator light comes on when the high beam of the headlight is switched on. EAU00061 Neutral indicator light “N” This indicator light comes on when the transmission is in the neutral position. EAU00057 Turn signal indicator light ” 5 ” This indicator light flashes when the turn signal switch is pushed to the left or right. 12 3 1. High beam indicator light “&” 2. Neutral indicator light “N” 3. Turn signal indicator light “5 ” EAU00095 Speedometer unit The speedometer unit is equipped with a speedometer, an odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance traveled. The tripmeter shows the distance traveled since it was last set to zero with the reset knob. The tripmeter can be used to estimate the distance that can be traveled with a full tank of fuel. This information will enable you to plan future fuel stops

POLINI MINICROSS AND MlNlMOTARD OWNER'S AND MAINTENANCE MANUAL

0

Filed Under (Polini) by admin on 22-11-2010

download
Fit the stand using the M8x18 screw to fasten it and the spring provided (photo 1 6). A DANGER! We suggest you to remove the stand during competitions as it could be dangerous and bruising. 18- Fit the gear lever l~hoto 171. 19- Fill the fuel tank (See section 4.13). 20- Check the engine oil level (See section 4.3). INTRODUCTION Always ensure that the motorcycle has been efficiently serviced and check it over before riding it. Take your motorcycle to an authorised POIJNI MOTOR1 dealer for all maior servicing and repair. Because of the manufacturer’s policy OF continuous development, and because of constant innovations in technology, your motorcycle may differ in some details from that described in the illustrations and text in this manual. Original POLlNl MOTOR1 spare parts are always made from the same materials and in the same way as the parts originally fitted to your minicross motorcycle. Always insist on original POIJNI MOTOR1 spore parts. Their use ensures a longer life and improved efficiency for your motorcycle. 2. STARTING THE ENGINE FOR THE FIRST TIME Always check over your motorcycle thoroughly before starting the engine. To start the engine for the first time, as instructed below. 1 – Turn the fuel tap located under the fuel tank to #ON” position (photo 18) Run your new motorcycle in as instructed How to ensure that the engine and transmission bed in correctly and to ensure continuous reliability in Future. A CAUTION! The first time yw ride your new motorcycle, ride for about two hours at low engine speeds to ensure that it runs in correctly. Also respect the following precautions. 2- Once the engine starts, leave it idle until it warms up to normal temperature. If you switch the engine off for a short time, wait for it to cool down completely before you re-start it. – 3- During the running in period, always ride at constant 2- Before starting the engine put the gear in neutral position speeds. AVOID RAPID ACCELERATION. (photo 19, gear N). 4- Even when riding at low engine speeds, avoid extended A WARNING! IF the gear position is not neutral the bike could move when started. 3- If the engine is cold, lift the choke lever on the carburettor (photo 20). A WARNING! Lower the starter lever again as won as the engine starts to warm up. 4- Leove the throttle closed. Pivot the kick-start lever out wards and push energetically downwards with your foot to start the engine. 5- Return the kick-start lever to its rest position. Leave the engine idle for a few minutes to warm it up. A WARNING! Check that the engine stop button stops the engine effectively before yw begin riding the motorcycle. difficult sections of road or Lck that could cause the engine to become very hot. 5- Once you have run in your motorcycle following all these instructions, take it to a Polini Motori dealer for its post- running-in service. Apart from a change of spark plug and engine oil, this service also includes the disassembly

Incoming search terms:

2001 URAL Classic Motorcycles Owner's Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Front brake control lever (Fig.1, #5). When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lamps are switched on. Kick lever (Fig.1, #11) is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Note: this is a backup to the electric starter. Gear shift foot pedal (Fig.1, #12) is a two-arm type. When the front arm is pressed, shifting from high to lower gears takes place. When the rear arm is pressed, shifting from low to higher gears takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift up if you rotate the heel of your left foot in towards the rear arm before stepping on it with your heel. The neutral position is fixed between the I and II gears. Throttle Control (Fig.1, # 6) is on the right handlebar. Turning the twist grip counterclockwise increases engine speed. Engine cutoff switch (Fig.1, # 7) has two positions, ignition off (up), and ignition on (down). Low and high beam light switch (Fig.1, # 15), turn indicator switch (Fig.1, #13) and horn push-button (Fig.1, # 14) are combined in one unit on the left-hand handle bar control housing. Master battery switch (Fig.1, # 21) is under the seat. Electric Start Button (Fig. 1, # 8) is located on the right-hand twist grip, below the kill switch. The steering damper absorbs lateral kicks on the front wheel. Turning tightening bolt (Fig.1, # 17) clockwise increases friction. This can be used while riding over bad roads. WARNING: DO NOT TIGHTEN THE DAMPER TO THE POINT WHERE THE STEERING BECOMES STIFF . DOING SO WILL ADVERSELY AFFECT HANDLING QUALITIES . Parking brake (Fig. 1, # 22) is located on the right side of the motorcycle next to the foot peg. It is engaged by applying the foot brake pedal fully and turning the handle and pushing it down to hold the foot brake lever in the applied position. Always disengage the parking brake before moving the motorcycle

1954 AJS MAINTENANCE MANUAL INSTRUCTION BOOK

0

Filed Under (AJS) by admin on 31-10-2010

download
Throttle twist grip. On right handlebar. Twist Inwards to open. When fully closed engine should just idle when hot. Air lever. Small lever on right handlebar Pull Inwards to Increase air supply to carburetter. Once set, when engine has warmed up, requires no alteration for different road speeds. Should be fully closed when starting engine from cold, Ignition lever. When fitted. Small lever on left handlebar. Advances and retards ignition point. Pull Inwards to retard. Retard two-fifths of total movement for starting. Valve lifter lever. Small lever close to clutch lever. Lifts exhaust valve from seat, releasing compression In combustion chamber, enabling engine to be easily rotated for starting. Also used for stopping engine if throttle stop is set as advised above. Clutch lever. Large lever on left handlebar. Grip to release clutch so that drive to rear wheel is disconnected. Front brake lever. Large lever on right handlebar. Grip to operate front wheel brake and, for normal braking, use in conjunction with rear brake application. Rear brake lever. Pedal close to left side foot rest. Depress with left foot to apply rear brake. Apply gently and use increasing pressure as the road speed decreases. Gear change lever. Pedal in horizontal position close to right foot rest. Controls selection of the four speeds, or ratios, between engine and rear wheel revolutions, with a ” free,” or neutral, position. See Illustration 2. Kick-starter lever. Vertical pedal on right hand side of gear box. Lighting switch, in top of head lamp. Controls lamps by a rotating lever which has three positions : (1) “OFF” Lamps not on. (2) ” L ” Pilot lamps, rear lamp and speedometer lamp on. (3) ” H ” Main head lamp, rear l amp and speedometer lamp on. Ammeter. In top of head lamp. Indicates flow of electric current, in, or out, of battery. (” Charge ” or ” Discharge.”) Horn switch. Press switch on right handlebar. Gear box filler cap. Located on top edge of kick-starter case cover. Allows Insertion of lubricant and access to clutch inner wire and internal clutch operating lever. Footrest for rider. Petrol tank filler cap. Located in top of fuel tank. To release, slightly depress, turn fully to the left, and then lift away. There are two locking positions. The middle position, between the fully tightened down and ” lift away ” positions, is in the nature of a ” safety ” device to prevent toss that might be occasioned by unauthorised meddling. Oil tank filler cap. Located on top edge of oil tank. The construction and operation is exactly as the petrol tank filler cap. Dipping switch. Trigger switch on left handlebar. Used to select normal or ” dipped ” beam of head lamp when main lighting switch lever is in the ” H ” position. (The main head lamp bulb has two filaments.)