HARLEY DAVIDSON HIGH OUTPUT ALTERNATOR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
this kit is designed for use on 1980 and later FLT and FLTC models, 1982 and later FXR, FXRS, and FXRT models and 1984 and later FXRD, FLHT, FLHTC, FXRDG, FXRS-SP, FXLR, FLHS and FXRC model vehicles. This kit contains the following parts: QTY DESCRIPTION 4 Screw, sockethead torx 1 Ring terminal 6 Cable strap 1 Rotor assembly 1 Spacer, thick 1 Spacer, thin 1 Stator assembly 1 Regulator Installation 1. Refer to applicable Service Manual for detailed removal and installation procedures. 1 CAUTION Disconnect battery (negative cable first) before performing any electrical system servicing. 2. Observe the following guidelines to ensure proper operation. A. Do not drop or pound on the new rotor assembly. Permanent damage can result. B. Do not install a new style rotor with an old style rectifier. Permanent rectifier damage can result. C. Do not install a new style rectifier with an old style rotor. Permanent rectifier damage can result. D. Route the black rectifier wire away from hot or moving parts. Secure it to the frame with cable straps. Trim excess wire length, crimp on ring terminal and attach to positive battery terminal. 3. See Figure 1. When installing rotor and stator use thin spacer inside and thick spacer outside of rotor

2001 HONDA CRF 230 Dual Sport Kit Installation Manual

0

Filed Under (Honda) by admin on 21-11-2010

download
1. Remove the seat, fuel tank, side panels, and front number plate. 2. Taillight and Turn signal Installation: Note that Baja Designs has updated this kit to use the new style LED taillight. The mounting is the same. Mount the rear taillight assembly to the rear fender as shown in Photos 1 and 2. Transfer drill the mounting holes in the taillight assembly into the fender and mount using the countersunk fasteners provided. The tail light lens should just line up with the end of the fender. Mount the turn signals into the side of the taillight assembly as shown in Photos 1, 2 and 3. The taillight has not been pre-drilled to allow placement of the turnsignals to be varied to accommodate different exhausts. Use a 3/8″ drill for the turn signal mounting hole 3 Photo 3 Photo 2 Photo 1
. 3. Brakelight Switch Installation: This is a tight fit on the CRF230 – take your time and it’ll work. Drill a 1/8″ hole in the brake lever 4 ½” from the center of the brake pedal pivot point (Photo4). 4 Photo 5 Drill 1/8″ hole here Photo 4 Install the brake-switch bracket under the right case bolt directly above the oil filler cap (Photo 5). Attach the spring to the hole you drilled in the pedal. Adjust the switch in the bracket so it engages about halfway through the pedal throw. You may need to lengthen (stretch) the spring slightly to allow proper switch adjustment. Turn-Signal Switch Installation: Install the turn signal switch on the handlebar next to the grip as shown in Photo 6 . The switch has a single screw that pinches it together on one side. Two tabs secure the switch halves on the other side. Remove the screw to separate the halves so that it can be installed on the handlebar. When installing the switch to the handlebar, make sure the tabs are seated in their locating holes and then tighten the pinch screw. DO NOT OVER TIGHTEN THIS SCREW, as too much force can strip the body of the switch. The clutch perch may have to be moved inward slightly to make room for the switch. Run the wires along the bottom of the handle

BMW Poly-V Belt – R 1100 Models

0

Filed Under (BMW) by admin on 16-11-2010

download
Information: In an effort to reduce service volume, a maintenance-free ribbed Poly-V belt was adopted on all R1100 models from engine number 38946130 onwards (09/94 production onwards). This belt does not need to be retentioned (even at the 600 mile service). The old belt required replacement every 24,000 miles. The new style belt is to be replaced every 36,000 miles. Use the same torque procedure as the old belt. Replacement of an old style belt with the new maintenance free belt requires the use of the new parts below: Parts Kit: 12 31 1 342 086 (kit consists of the following) In addition to the Poly-V belt, the following parts were also changed: 1. Top pulley new: steel old: Aluminum 2. Bottom pulley new no spot welds: old: steel w/three spot welds on front 3. Belt new: Ribbed, printing on belt (1342059 Fa. Dayco) or (1341779 Fa. Conti) Slight squeaking may be heard for a short time after a cold start when temperature is below 50°F. The belt should reach it’s correct operating tension soon after the start up. The belt only needs retentioned if the slight squeaking does not stop after warm up.

Cobra JR/ OI Radiator with Louvers Replacement

0

Filed Under (Cobra) by admin on 10-11-2010

download
The 2009 model year radiator for Cobra JR (also remaining OI ) model will be FCCJ0004 which now has provisions for louvers. On the 2009 models these louvers also rely on a feature on the frame down-tube for mounting the plastic louvers. Older models do not have these features on the frame and so it is not possible to utilize the louver mounts on the radiator. Customers with older models JR/CM or OI/P3/PW3 needing a replacement radiator for ECMU0061 or ECMU0225 will be sold a radiator kit FKMU0001 which includes the new style radiator, FCCJ0004C (with louver mounting tabs removed), and all mounting hardware. This will allow the mounting of the new style radiator onto these products without mounting the louvers. As the 2009 frame is now the service replacement frame for JR/CM & OI/PW3/P3 models from 2004 – 2008, the louvers are able to mount on all older models JR/CM & OI/PW3/P3 that have the appropriate mounting provisions. Welding on the highly stressed down-tube frame member is not recommended by Cobra because it can cause premature structural failure to the frame and possible injury to the rider.