1953 Toyota Ford Truck Power Steering Conversion Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 01-10-2011

download
of all wiring, brake lines and fuel lines. 2. Bolt the Toyota box to the mounting bracket so that the long arm of the bracket points in the same direction as the steering column input shaft (small shaft.) To mount the bracket and box correctly, the longer end should be towards the rear of the vehicle. It may be necessary to grind on the power steering box where the two flanges protrude above the bracket. For technical help call Classic Performance Products Monday thru Friday 8:30am to 5:00pm at (714) 522-2000. Rev. 8/17/2009 3. Locate the box/bracket assembly into the frame by centering the Toyota sector shaft through the original hole in the frame. This hole will need to be elongated approximately 3/8″ to allow the sector shaft to clear the frame. Bolt the bracket directly into the mounting holes for the original steering box. 4. With the first bolt in, check the fit by reattaching the steering box. Make sure the splined shaft goes through the frame without interference. Torque down the mounting bolts to 45 lbs. 5. Attach the pitman arm to the steering box. Before this is done the steering sector must be centered. Turn the input shaft clockwise as far as it can go. Make a reference mark. Now turn the shaft counter clockwise as far it can go and be sure to count the turns. Turn the shaft back half the distance and now the box is centered. Be sure to double and triple check this procedure. Attach the pitman arm to the output shaft with the output shaft nut. Torque the bolt down to 110ft/lbs. Reconnect the stock drag link and you are on your wa

Harley Davidson 2004-Up Sportster EZ-Steer Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Installation Notes • Remove front fender, wheel, brake caliper, and fork tubes. • Remove all components attached to stock triple clamps, then the triple clamps themselves. • Remove upper and lower bearings including race. • Install new steering stem bearing races into neck. • Install new upper steering stem bearing with seal into neck. • Install Top and Bottom triple clamps into neck and snug steering stem bolt with washer. • Remove fork tube cap from both forks. • Install fork extensions with o-ring into fork tubes and tighten until fully seated. • Install fork tube caps with o-rings and tighten (see torque table). • Slide fork tubes into triple clamps until the top of each tube cap extends 0.42-0.50 in. above top surface of upper triple clamp. • Tighten 3/8-16 x 1.5″ bolts on upper triple clamp (see torque table). • Tighten steering stem bolt (see torque table). • Tighten pinch bolts on lower triple clamp (see torque table). • Install front wheel assembly and front brake caliper. • Install front fender. Item # Part Description Torque Spec (Lb. Ft.) – Fork Tube Cap 22-58 8 Bolt, Steering Stem, SP 30-35 11 3/8 – 16 X 1.5″ Socket Head Cap Screw 30-35 EZ-Steer Maintenance The bearings in your EZ-Steer rake kit are normal wear items, not subject to replacement under Champion’s one year Limited Warranty for the product. Failure to follow your motorcycle manufacturer’s recommendations for periodic OEM triple-tree maintenance will accelerate the wear on these bearings. Checking/adjustment of the steering stem nut torque with the front end lifted, in accordance with your motorcycle manufacturer’s recommendations, is important to reliable bearing service. Windshield Notes Please note that this EZ-Steer kit accommodates all known windshield types with the exception of a minor modification to Quick Release Compact Windshield, example part no. 58063-04. You will need to oblong the lower bolt holes as shown in figure

Incoming search terms:

HARLEY DAVIDSON HORN COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat and disconnect wires from horn. 2. See Figure 1. Remove stock horn bracket nut (2) and the entire stock horn cover assembly (1). Remove the horn (3) and all hardware components from the stock cover including wire clamp, clips, and mounting bracket. Leave rubber mount and locknut on motorcycle. Note assembly order for kit installation. NOTE Do not over-tighten “horn to horn cover” nut. Over-tightening may result in permanent damage to the horn. 3. Apply Loctite 271 (Red) to threads of nut (4) fastening the horn to the horn cover. Tighten nut to 80-100 in-lbs (9.0- 11.3 Nm). Tighten screws fastening the horn cover to the horn bracket to 35-55 in-lbs (4.0-6.2 Nm). 4. Route wiring harness through the clamp (if present) and install the entire horn cover assembly to the mounting stud (5). 5. Tighten nut (2) fastening the horn bracket to the horn rubber mount to 80-100 in-lbs (9.0-11.3 Nm). Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 6. Connect wires to terminals and reconnect battery. NOTE Horn is not polarity sensitive. Ground and power wire may be connected to either terminal. 2 4 1 5 3 is03958 1. Horn cover assembly 2. Bracket nut 3. Horn 4. Nut 5. Mounting stud Figure 1. Horn Cover Installation 7. Test horn. NOTE Test the horn only when mounted on the vehicle. The sound may be muffled if tested when hand-held. A muffled sounding horn that is mounted to a vehicle may indicate permanent damage to the horn by over-tightening the horn to horn cover nut (Figure 1, Item 4). Attempt to adjust nut torque. Replace horn if necessary. 8. Reinstall seat

Incoming search terms:

Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms: