2003-2007 Kawasaki Ninja ZX6R/ RR HID Installation Removal Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
take out the original bulb and install the HID bulb. Be careful, do not touch the HID bulb at any time. Plug in the power wires into the original power plug. They go in easy and slide right in. Black wire connects into the black wire on the plug. On the right side, pink goes to red. On the left side, blue goes to red as these are positive wires. Pull the wires toward you slowly and carefully as you near the cover toward the headlight. Spin the rubber grommet if you need to line up the dust cover to the head light. Now lock it in. The arrow should point up if it is locked in properly. Left side installed the same way as the right. Mount the ballasts on the under side of the cowling covers with two nuts and bolts. Position the ballast in the proper place. Then, hold in one spot while drilling two holes for the bolts. An alternate mounting may be with industrial double sided tape or industrial Velcro. Do not use those cheap double sided tape of Velcro mounts as they will not hold the weight of the ballasts. Close up of underside of the cowling cover with ballast installed.
Top side of the cowling cover. Repeat installation on the second cowling. Then reinstall on the bike, connecting all the plug wires.

harley davidson oil filter cooler installation instructions

0

Filed Under (Harley Davidson) by admin on 10-04-2012

download
2000 cH ROME 99 – 07 SOFTAIL MODELS #2001 CHROME 99 – 07 DYNA MODELS #2002 CHROME 99 – 07 FLT MODELS, flht, flhr, fltr #2005 black CHROME 99 – 07 SOFTAIL MODELS #2006 BLACK CHROME 99 – 07 DYNA MODELS #2007 black CHROME 99 – 07 FLT MODELS, flht, flhr, fltr #2020 REPLACEMENT OIL FILTER #’S: 2000, 2001, 2002, 2005, 2006, 2007 1. See Figure 1 to verify all Feuling components and the proper mounting bracket for your model 2. Wash, clean and inspect all new Feuling hardware, Including – off-set sandwich oil filter adapter, filter cooler housing and oil lines, use compressed air to blow dry the oil lines, fittings, threads and bolt holes. Use a tap and die if needed to clean threads. (On installation use lubrication on all fasteners and fittings) 3. Refer to the proper service manual for your model motorcycle & engine, for removal of engine oil and spin-on oil filter. Dispose of these items properly. 4. Clean engine case oil filter spigot and sealing surface thoroughly. 5. Install the clean Feuling off set oil filter sandwich adapter; both O-ring and gasket need to be assembled dry. 6. First install the inside half of the off-set oil filter adapter, O-ring side towards engine case filter mount. We recommend using a dab loctite on the 1″ lock nut. (See figure 2) It is recommend to mock up the sandwich adapter before torquing nuts and bolts to obtain desired orientation and proper clearance to engine case and frame rails. 7. Install the fittings and oil lines onto the outer half of sandwich adapter torque fittings to proper specs using thread sealant on the 1/8 NPT threads and engine oil on the -4 AN oil line fittings. 8. Complete installation of sandwich adapter, including the inner gasket. Finger tight the allen head bolts in an alternating sequence on both sides before final torque. Re-Torque the allen head bolts after the first heat cycle after installation and during every oil change.

Harley Davidson Ignition Switch Installation Manual

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
Ignition Switch a. Harley Davidson i. P/N 71313-96 ii. P/N 71510-93 b. Drag Specialties i. P/N DS-272187 c. JP Cycles i. Cat # 370333 3. Wires and Connectors a. 14 gage wire – Red, 15 inches long b. 14 gage wire – Orange, 15 inches long c. 14 gage wire – Grey, 15 inces long d. 14 gage wire – Brown, 15 inches long e. 14 gage Female Wire Terminals (x3) 4. Miscellaneous a. Radio Shack i. 100 Ohm Resistor (1/4 Watt, 5% Tolerance) – P/N 271-1108 ii. Also recommended – piece of PC board to solder wires and resistor to b. Heat Shrink Tubing – Pack of Assorted Sizes c. Duct Tape or Masking Tape d. 6″ (or longer) Zip (Cable) Ties 2. Nuts and Bolts a. For Switch Mount: i. 4x 6-32 (Chrome or SS) countersink screws ii. 4x nuts for above iii. 4x washers for above b. For Door Locking Mechanism: i. 5/16-18 Bolt (or stud) ii. 2x 5/16-18 nuts iii. Block of rigid material 1. Dimensions: 5/16″ x 9/16″ x 3/8″ 2. Material: Aluminum, Stainless Steel, PVC, etc (Anything rigid will do) iv. 5/16-18 Tap v. Series of drill bits up to 9/32″ (drill size required for 5/16-18 tap) i. Roll (or Spring) Pin and drill bit 1/32″ smaller than pin

Honda VTX C 1800/ 1300 Backrest Kit Installation Manual

0

Filed Under (Honda) by admin on 04-01-2012

download
We highly recommend use of Loctite о on all nuts and bolts and check your hardware on regular basis. 1) Install the backrest bars with the pad. Do not tighten the bolts until the backrest is assembled with the brackets Install the brackets and backrest. The longer collars go to the front mounting holes. Do NOT tighten all the bolts until everything is assembled. We highly recommend red loc-tite о or any other compound will prevent bolts getting loose from vibration. Check bolts and metal parts periodically to make sure they are securely fastened

Yamaha V-Star 650 Engine Guard REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Protect the rear portion of the front fender with a towel or other thick, soft cloth. Remove the OEM engine guards if they have been installed on the motorcycle. Your new Barons engine guard will fasten to the frame at the same points as the OEM guard and will use the same hardware. 2. Or, if OEM engine guards are not present, remove the 14mm bolts from the underside of the drivers footpeg mounts. 3. Remove the 12mm upper engine mount bolts located on both sides of the frame. Replacement bolts are included with your new engine guard. 4. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 5. Raise the guard until the holes in the lower mounting brackets align with the vacated bolt holes beneath the drivers footpegs. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the large washers (supplied with the guard) between the rear face of the lower bracket and the frame. The washer fills the space between the lower mounting bracket and the footpeg mount. Reinsert the 14mm bolts and finger tighten. 7. Rotate the guard until the holes in the upper mounting brackets align with the empty holes on each side of the frame. 8. Insert the replacement 13mm bolts, along with their washers, and tighten securely. Tighten all other nuts and bolts securely. 9. Remove the protection on the front fender and you’re ready to ride. CAUTION!!! You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

Honda Shadow Backrest Kit Installation Manual

0

Filed Under (Honda) by admin on 07-12-2011

download
Install the right and left brackets, leave screws loose to allow brackets some movement for ease of backrest installation. Install the ackrest as shown, if optional carrier is also purchased, use the longer flange bolts provided. Note the backrest goes inside of the brackets, and carrier rack (optional) will go outside of the brackets when installed. Tighten all nuts and bolts to the torques specified

SUZUKI SV1000/ S SERVICE MANUAL Supplimentary

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CHASSIS BOLT AND NUT Check that all chassis bolts and nuts are tightened to their specified torque. (Refer to below and page 2-29 of SV1000S Service manual for the locations of the following nuts and bolts on the motorcycle.) CHASSIS FRONT FORK REMOUNTING Align the upper surface A of the inner tube with the upper surface B of the steering stem upper bracket. Tighten initially at 1 000 km (600 miles, 1 month) and every 6 000 km (4 000 miles, 6 months) thereafter. ITEM N·m kgf-m lb-ft 1 Handlebar clamp bolt 23 2.3 16.5 2 Handlebar holder set nut 45 4.5 32.5 SV1000K3 5 SUSPENSION SETTING After installing the front fork, adjust the spring pre-load and damping force as follows. SPRING PRE-LOAD ADJUSTMENT There are eight grooves on the spring adjuster. Position 1 provides the maximum spring pre-load and position 8 provides the minimum spring pre-load. STD position: 7 DAMPING FORCE ADJUSTMENT Rebound damping force Fully turn the damping force adjuster 1 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 and 1/4 turns out from stiffest position Compression damping force Fully turn the damping force adjuster 2 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 turn out from stiffest position STANDARD FRONT SUSPENSION SETTING ! FRONT Spring pre-load adjuster Damping force adjuster Rebound Compression Solo and dual riding 7 1 and 1/4 turns out from stiffest position 1 turn out from stiffest position Be sure to adjust the spring pre-load and damping force on both front fork legs equally. 6 SV1000K3 HANDLEBARS REMOVAL AND DISASSEMBLY Remove the handlebar balancer 1. NOTE: Do not remove the handlebar balancer mounting screw before removing the handlebar balancer. Slightly loosen the mounting screw, and then pull the balancer assembly out of handlebars. Remove the rear view mirror 2. Disconnect the front brake light switch coupler 3. Remove the front brake master cylinder. Remove the right handlebar switch 4 and throttle grip 5. Disconnect the clutch switch lead wires 6. Remove the left handlebar switch 7. Remove the rear view mirror 8. Remove the clutch master cylinder. Remove the handlebar clamp caps

Incoming search terms:

HARLEY DAVIDSON SPORTSTER® ACCESSORY SLIP-ON MUFFLER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Remove mufflers using appropriate Service Manual instructions. 3. Discard gaskets and mufflers. 4. Install new gaskets on mufflers. 5. Slip muffler clamps on mufflers. 6. Loosely attach mufflers to the interconnect tube using existing screws and washers. 7. Position the ends of the front and rear exhaust pipes into front and rear cylinder heads and align exhaust system while tightening all nuts and bolts; begin at the cylinder head exhaust ports and work back toward the mufflers. a. Finger tighten the upper nuts to the mounting studs. b. Tighten the lower nut to 9-18 in-lbs (1.0-2.1 Nm) . c. Tighten the upper nut to 60-80 in-lbs (6.8-9.0 Nm) . d. Tighten the lower nut to 60-80 in-lbs (6.8-9.0 Nm) . 8. Tighten the acorn nut on the rear exhaust pipe support clamp to 15-19 ft-lbs (20.3-25.8 Nm) . 9. Tighten muffler clamps to 45-60 ft-lbs (61-81.3 Nm) . 10. Tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm)

HARLEY DAVIDSON SPORTSTER MUFFLER SLIP-ON KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect negative (-) battery cable. 2. Remove mufflers using appropriate service manual instructions. 3. Discard gaskets and mufflers. 4. Install new gaskets on mufflers. 5. Slip muffler clamps on mufflers. 6. Loosely attach mufflers to the interconnect tube using existing screws and washers. 7. Position the ends of the front and rear exhaust pipes into front and rear cylinder heads and align exhaust system while tightening all nuts and bolts, beginning at the cylinder head exhaust ports and work back toward the mufflers. a. Finger tighten the upper nuts to the mounting studs. b. Tighten the lower nut to 9-18 in-lbs (1.0-2.1 Nm) . c. Tighten the upper nut to 60-80 in-lbs (6.8-9.0 Nm) . d. Tighten the lower nut to 60-80 in-lbs (6.8-9.0 Nm) . 8. Tighten the acorn nut on the rear exhaust pipe support clamp to 15-19 ft-lbs (20.3-25.8 Nm) . 9. Tighten muffler clamps to 45-60 ft-lbs (61.0-81.3 Nm) . 10. Tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm) . 11. Connect negative (-) battery cable.

HONDA VT750 EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 24-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the header flange nuts at the exhaust port on the front and rear head pipes. 2. Remove the two 8mm nuts from the muffler mounting bracket, while supporting the entire exhaust system. Lower the system down and set it aside. Note: Save the stock hardware for reuse. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install the muffler mounting bracket (stamped 268) to the original muffler mounting point, using the two stock 8mm nuts. Refer to figure 1. 3. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of the front muffler. 4. Install the front head pipe to the cylinder head using the stock nuts. Attach the muffler to the mounting bracket using the two 5/16″ flange bolts (supplied). Leave the nuts and bolts loose at this time. 5. Repeat steps 2 and 3 with the rear header. 6. Align the mufflers so they are parallel when viewing from the right hand side of the motorcycle. Tighten all the hardware evenly. 7. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. 8. Rotate the hose clamps on both heat shields so they are accessible with a screw driver and tighten each of them evenly. The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Note : The heat shields should cover the weld on the muffler. 9. Be sure to remove any dirt, oil or finger prints from the entire exhaust system before starting the motorcycle.