Harley-Davidson Softail, Touring, Dyna, Sportster and V-Rod, SELF LEARNING MODULE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2012

download
STEP 1 – BATTERY CONNECTION Locate the battery and disconnect the negative battery cable. Mount the module in the open area in front of the battery with 2-tie straps or velcro straps, directing the harness from the module towards the 6 o’clock position. STEP 2 – THROTTLE POSITION SENSOR (TPS): Remove the air cleaner assembly and unplug the TPS sensor connector at the TPS sensor. The harness includes (2) TPS connectors which should be routed under the gas tank into the factory wire loom to the TPS sensor. The TPS sensor is located on the left side of the throttle body. Plug the (2) TPS connectors from the module in between the TPS sensor and to the factory TPS connector. STEP 3 – O2 SENSOR: Systems equipped with factory O2 sensors Rear: Unplug the Rear O2 sensor connector from the factory harness, which is located at the Rear exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors and connect one connector to the Rear O2 sensor and connect the other connector to the main factory O2 sensor connector. Front: Unplug the Front O2 sensor connector from the factory harness, which is located at the Front exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors, and connect one connector to the Front O2 sensor and connect the other connector to the main factory O2 sensor connector. Systems not equipped with factory O2 sensors NOTE: Many aftermarket exhaust systems are now equipped with plugged O2 sensor bungs which can be removed to accept an aftermarket O2 sensor. Typically these bungs already have a thread size of 18 mm x 1.5 mm. Exhaust systems not equipped with O2 sensor bungs need to have the supplied 18 mm x 1.5 mm thread size bung welded to the exhaust pipe in order to install an O2 sensor. The O2 sensor bung should be installed 3 to 6 inches away from the rear cylinder exhaust port and in front of the exhaust torque tube pipe area. The module prefers to receive information from the O2 sensor from an area that is NOT contaminated from atmospheric air. This air may enter through the tail pipe of an unrestricted or un-baffled exhaust pipe. The bung should not be installed in the “5 to 7 o’clock” area. If mounted in this area the O2 sensor can be damaged. The moisture from the gases exiting from the rear cylinder exhaust port will harm the ceramic shell element of the O2 sensor.

Incoming search terms:

YAMAHA ROADLINER / STRATOLINER REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 04-01-2012

download
1. Cover the right frame tube in front of the exhaust with duct tape or any suitable material to protect frame during exhaust removal. 2. Remove the three capscrews holding the muffl er assembly to the support bar, loosen the muffl er clamp and carefully remove the muffl er from the motorcycle. 3. Remove and save the two 12mm bolts from the right side fl oorboard assembly (Figure 1) and carefully lower the fl oorboard out of the way. NOTE: Support the fl oorboard with a block of wood or other appropriate material, do not let it “hang” by the brake switch wire. 4. Remove the chrome cover over the power valve pulley. Using a 10mm wrench, remove both cables attached to the power valve pulley (Figure 2). 5. Remove and save the 5mm capscrew on the rear side cover to gain access to the O2 sensor harness plug and unplug O2 sensor from harness (Figure 3). 6. Remove the 4 nuts holding the exhaust system and carefully remove the exhaust system from the motorcycle (may require assistance). NOTE: It may be necessary to loosen the heatshield clamps to access the nuts on the front cylinder. 7. Trace the power valve cables to the drive motor (just under the rear fender on the right side). Remove the power valve cables and mounting clips from the motorcycle. 8. Using a 22mm wrench, carefully remove the O2 sensor from stock exhaust system and save for reuse with the new system. 9. Remove the plastic cover over the clutch banjo bolt (Figure 4). 10. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them

HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

HARLEY DAVIDSON TOURING MODEL DRESSER DUALS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-12-2010

download
1. Remove both left and right saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffl er. 3. Remove the two 5/16″ bolts that mount the muffl er to the saddlebag supports. Repeat this step on the opposite muffl er (save these parts, they will be re-used). 4. Remove the stock muffl ers with sliding hangers and set them aside. NOTE: It may be necessary to use a penetrating lubricant to loosen the muffl er from the head pipe. 5. Find and unplug the O2 sensor wires from the wiring harness and remove cable tie holding front wire to frame. F eed the end of the wires through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing for re-installation. 6. Remove the right hand fl oor board. 7. Remove both passenger fl oor boards. 8. Loosen the heat shield clamps on both front and rear exhaust pipes. 9. Loosen the rear head pipe clamp located behind the rear cylinder. Remove the section of head pipe connecting the left side muffl er. 10. Remove the nut and carriage bolt holding the front head pipe to the bracket on the transmission housing (save these parts, they will be re- used). 11. Remove the two mounting nuts from each head pipe, located at the cylinder head. Carefully remove the head pipes and set them aside. 12. Using a 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 13. Remove the rear cylinder bracket by removing the two starter mounting bolts. Install new bracket (stamped 422-P)(supplied) and torque to 13-16 ft. lbs. (Figure 1). NOTE: Twist breather hose down towards the left hand side to get it as far away from the pipe as possible. 14. Install mounting post (from stock system) so the nut is accessible from right side of motorcycle and saddle will support underside of exhaust pipe. 15. Replace the bracket on the transmission housing with new bracket (stamped 423-P)(supplied) and torque to 13-16 ft. lbs. (Figure 2). 16. Carefully remove the exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted, replace them.

Incoming search terms: