Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

Incoming search terms:

BMW F800 GS Rider's Manual

0

Filed Under (BMW) by admin on 26-11-2010

download
General view, left side 1 Power socket (74) 2 Seat lock (55) 3 Engine-oil filler neck and oil dipstick (87)
2 12 z General views General view, right side 1 Fuel filler neck (66) 2 Brake-fluid reservoir, rear (91) 3 Vehicle Identification Number (VIN) (on steering-head bearing), Type plate (on steering-head bearing) 4 Brake-fluid reservoir, front (90) 5 Coolant level indicator (behind side panel) (91), Coolant filler neck (behind side panel) (92) 6 Adjuster for springpreload, rear (51) 7 Adjuster for damping characteristic, rear suspension (52)
Underneath the seat 1 Location of first-aid kit (OA) 2 Toolkit 3 Payload table 4 Table of tyre pressures 5 Helmet holder (56) 6 Rider’sManual 7 Tool for adjusting spring preload (51) 2 14 z General views Underneath the trim panel 1 Battery (112) 2 Air-filter housing (110) Handlebar fitting, left 1 Operating the on-board computerOE (39) 2 Operating the ABSOE (49) 3 Horn 4 Flashing turn indicators, left (46), Hazard warn- ingflashers (47) 5 High-beam headlight and headlight flasher (45)

BMW K 1100 LT/ RS Repair And Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
Transmission cover to transmission 9 Machine screw for neutral stop 13 Stud bolt, selector shaft 17 (Loctite 243) Transmission to intermediate flange 16 Frame mounting to transmission 45 Bearing mount to transmission 41 (Loctite 243) Starter motor to transmission 9 Positive lead to starter motor 5 Fixed bearing of swinging arm to transmission 9 Swinging arm bearing journal (loose bearing) 7,5 Locknut of bearing journal 41 Fixed bearing rear wheel drive in swinging arm 150 (clean thread + Loctite 2701) Bearing pin, loose bearing rear wheel drive in swinging arm 7 (clean thread + Loctite 2701) Locknut, loose bearing rear wheel drive in swinging arm 105 (clean thread + Loctite 2701) Suspension strut to frame/rear wheel drive 51 Brake caliper 32 Hinterradschraub en 105 Exhaust to cylinder head 21 Silencer to holder/footrest plate 9 Front silencer to transmission 12 Footrest plate to transmission 15 31 Front fork Oil filler plug 10 Oil drain plug 3,5 Spring support bearing 20 Locking tube 65 Hexagon nut 65 Clamping screws of fork bridges 15 Bottom screw fitting 47 Handlebar clamp block 22 Fork stabilisor

Incoming search terms: