1983 MODEL CB1000C SETUP INSTRUCTIONS

0

Filed Under (Honda) by admin on 08-11-2011

download
heck oil level in final drive gear case and, if necessary, fill gear case up to filler neck with recommended oil. Reinstall and tighten fillef cap With motorcycle still on center- stand, remove dual range transmission protector cover by removing two screws. Remove oil filler cap Remove oil level check bolt and check that oil level is even with lower edge of hole. If necessary add recommended oil. Reinstall oil level check bolt and filler cap Tighten filler cap. Tighten oil check bolt to specified torque and reinstall protector cover

YAMAHA RX10H/ RX10SH RX10MH/ RX10MSH/ RX10RH/ RX10RSH SERVICE AND OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Throttle override system (T.O.R.S.) If the carburetor or throttle cable should malfunction during operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the ignition and keep the engine revolution speed between 2,800 and 3,000 r/min if the carburetor fails to return to idle when the lever is released. Speedometer unit The speedometer unit is equipped with the following: a digital speedometer (which shows riding speed) an odometer (which shows the total distance traveled) a tripmeter (which shows the distance traveled since it was last set to zero) warning indicators (which show self-diagnosis, cool ant temperature, fuel level, and oil level warnings) fuel meter (which shows the fuel remaining in the fuel tank) grip/thumb warmer heat level indicator  (which shows the heat level of the grip warmer or the thumb warmer) After the engine is started, the tachometer 1 makes one sweep, and the warning light 2 and all segments of the meter 3 turn on and off once. Then the warning light turns on again, and then goes off if there are no problems. The grip warmer heat level is initially displayed for 5 seconds, then switches to the fuel meter display. Odometer and tripmeter modes Pushing the select/reset button 4 switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP”. To reset the tripmeter, push the select/reset button for at least one second while the tripmeter is displayed. NOTE: @ To switch the speedometer, odometer, and tripmeter displays between kilometers and miles, select the odometer mode “ODO”, and then push the select/reset button 4 for at least 10 seconds. ESU00363 High beam indicator light The high beam indicator light 1  comes on when the high beams of the headlights are switched on. (See page 5-12 for headlight beam switch operation.)

YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

HONDA CT110 OWNERS MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
ENGINE OIL Engine Oil Level Check Check the engine oil level each day before riding the motorcycle. The level must be maintained between the upper (2) and lower (3) marks on the dipstick (1). 1. Start the engine and let it idle for a few minutes. 2. Stop the engine and hold the motorcycle in an upright position on firm, level ground. 3. After a few minutes, remove the oil filler cap/dipstick, wipe it clean, and reinsert the dipstick without screwing it in. The oil level should be between the upper and lower marks on the dipstick. 4. If required, add the specified oil up to the upper level mark. Do not overfill. 5. Reinstall the oil filler cap/dipstick, check for oil leaks. CAUTION Running the engine with insufficient oil can cause serious engine damage. TYRES Proper air pressure will provide maximum stability, riding comfort and tire life. Check tire pressure frequently and adjust if necessary. NOTE Tire pressure should be checked before you ride while the tyres are cold. Select the right replacement tire in accordance with the following specifications: Cold tire pressures kPa ( kg/cm2, psi ) Front: 175 ( 1.75, 25 ) Rear : 225 ( 2.25, 33 ) Tire size Front: 2.75 – 17 41P Rear : 2.75 – 17 41P Check the tires for cuts, embedded nails, ore other sharp objects. See your authorized Honda Dealer for replacement of damaged tires or punctured inner tubes OPERATION PRE-RIDE INSPECTION WARNING If the Pre-ride Inspection is not performed, serious damage or an accident may result. Inspect your motorcycle very day before you ride it. The items listed here will only take a few minutes to check, and in the long run they can save time, expense and possibly you life. 1. Engine oil level – add engine oil if required. Check for leaks. 2. Fuel level – fill the fuel tank when necessary. Check for leaks. 3. Brakes – check operation. Adjust free play if necessary. 4. Tyres – check condition and pressure. 5. Drive chain – check condition and slack. Adjust and lubricate if necessary. 6. Throttle – check for smooth opening and full closing in all steering positions. 7. Lights – check that headlight, tail/brake light, turn signals, indicators. 8. Engine stop switch – check for proper function. 9. Battery electrolyte – check the level and add if necessary Correct any discrepancy before you ride. Contact your authorized Honda dealer for assistance if you cannot correct the proble

Incoming search terms:

HARLEY DAVIDSON ENGINE/TRANSMISSION INTERFACE AND TOP COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 1 4 3 2 is03621 1. Transmission top cover screw (3) 2. Upper and lower rear bearing housing screw (2) 3. Upper front bearing housing screw 4. Lower front bearing housing screw Figure 1. Interface Cover Installation 2. See Figure 1. Remove the two rear bearing housing screws (2) from the side of the transmission case. 3. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 4. See Figure 2. Obtain the rear interface mounting bracket (1) from the kit. 5. Apply a few drops of Loctite 243 (Blue) to the threads of the two bearing housing screws removed in Step 2. Install the rear interface mounting bracket to the bearing housing with the screws, and tighten to 13-18 ft-lbs (17.6-24.4 Nm) . 6. See Figure 1. Remove the upper front bearing housing screw (3) from the side of the transmission case. Loosen the lower front bearing housing screw (4). 7. See Figure 2. Obtain the front interface mounting bracket (2) from the kit. 8. Apply a few drops of Loctite 243 (Blue) to the threads of the upper front bearing housing screw removed in Step 6. Hook the slot in the front interface mounting bracket under the loosened lower screw head. Install the bracket to the bearing housing with the upper screw, and tighten both screws to 13-18 ft-lbs (17.6-24.4 Nm) . 9. See Figure 1. Remove and retain the three socket head cap screws (1) that fasten the right side and left front corner of the transmission cover. 10. Remove and retain the screw fastening the rear brake line P-clamp to the rear fork bracket. 11. See Figure 2. Obtain the right rear interface cover (3), two chrome 1/4-20 screws (6) and two flat washers (7) from the kit. 12. From the rear of the motorcycle, bring the right rear interface cover into position behind the rear exhaust pipe, over the bearing housing. The hole in the top surface of the cover should be positioned over the right rear transmission top cover hole. 13. Loosely fasten the interface cover to the rear interface mounting bracket with the two chrome screws and flat washers. 14. Obtain the chrome top interface cover (4) from the kit. 15. Position the top interface cover over the transmission top cover, overlapping the tab at the top front of the chrome right rear interface cover

HONDA VTX 1300 AND 1800 TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 17-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25 psi. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with 1 quart of SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. Check the oil level every 10,000 miles, or sooner if you experience leaks, and refill as necessary. Do not fill higher than the fill-hole. Change the differential oil every 30,000 – 35,000 miles. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . If your driveshaft U-joint and/or spline are fitted with grease fittings, pump the fittings with wheel- bearing, graphite or high-pressure grease every 3000 to 5,000 miles. If yours does not have grease fittings then lubrication is not required. 7. Suspension System : The suspension system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight)

Incoming search terms:

HONDA GOLD WING GL1500 AND GL1800 TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25 psi. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with 1 quart of SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. Check the oil level every 10,000 miles, or sooner if you experience leaks, and refill as necessary. Do not fill higher than the fill-hole. Change the differential oil every 30,000 – 35,000 miles. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . If your driveshaft U-joint and/or splines are fitted with grease fittings, pump the fittings with wheel-bearing, graphite or high-pressure grease every 3000 to 5,000 miles. If yours does not have grease fittings then lubrication is not required. 7. Suspension System : The suspension system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight): GL1500: The OEM adjustable air shock is used in conjunction with two (2) new Progressive 416 air shocks. The three shocks should be pressurized to about 20 psig, but to no more than 70 psig; GL1800: You can still use your OEM mono-shock pre-load adjustment. Your two (2) new coil-over shocks do not have an air system connection. However, there is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals. 9. Electrical : Your trike is pre-wired for a trailer connection. The harness is just below the trunk door on the underside of the body.

Incoming search terms:

Street Fork Spring Installation Instructions

0

Filed Under (Tips and Review) by admin on 13-02-2011

download
1. Remove fork springs according to instructions contained in your shop manual. For maximum performance we highly recommend that the forks be thoroughly cleaned, inspected and new fork oil installed. Note: If your motorcycle comes equipped with two fork springs in each leg (long & short), remove and discard both springs and the flat washer between the springs. If a stock spacer exits, remove it. If there is a short spring on the damper rod, do not remove it! 2. Use the recommended fork oil viscosity as noted in your owners manual with the following exceptions: GL1100 20 weight, GL1200/1500 15 weight required. See fine tuning for more in- formation. Fork oil level/volume should be checked according to the steps outlined in your authorized shop manual. Measurement of your fork oil by level is the preferred method. However, some manuals only specify a volume measurement. Due to the design of a progressive wound fork spring it will displace more oil thus requiring a maximum oil level of 5.5″ (140mm). Caution: This is not a recommendation, it is only a precautionary statement. If your manual specifies an oil level higher than 5.5″ (140mm) set the oil level at 5.5″ (140mm). (Oil level is the distance from the top of the fork tube to the top of the oil with the fork completely collapsed and the fork spring removed see figure 1.) This measurement can be made by using either one of the Progressive Suspension Fork Oil Level Adjusters (FOL-1 or FOL-2). 3. Install your new fork springs into the forks. Mechanically, it makes no difference which way the springs are installed. Some manuals will state; install the spring with the close wound end towards the bottom. This is done because sometimes there will be less spring noise. The springs will perform exactly the same regardless of which direction they are placed. Check the spacer length requirement for your motorcycle in the enclosed supplement. If not listed, you must calculate the pre-load. What is pre-load? Pre-load is the distance the spring compresses when the fork cap is installed. You may or may not utilize a spacer to achieve proper pre-load. The spacer in itself is not “pre-load”. It just helps to achieve it. Why is pre-load important? It determines the proper ride height which in turn affects how the bike handles.

HARLEY DAVIDSON LCD OIL TEMPERATURE/ LEVEL DIPSTICK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
LCD DIPSTICK INSTALLATION 1. Remove the original equipment (OE) dipstick from the filler neck. 2. Non-threaded Dipsticks: Lightly oil the O-ring on the new LCD dipstick. Orient the dipstick so that the display window is horizontal and readable from left to right, with the Bar and Shield logo to the left (towards the rear of the motorcycle). Push the dipstick straight into the filler neck until it seats. 3. For threaded dipsticks: Lightly oil O-ring and screw into the transmission like OE dipstick. If the orientation of the display is unsatisfactory when fully seated, refer to Adjusting the Display Angle later in these instructions. NOTE To be sure of correct readings, the dipstick MUST seat firmly against the flange. LCD DIPSTICK USE AND CARE Removing the Dipstick The dipstick assembly must be removed from the filler neck to add oil or to service the internal battery. Displaying the Oil Temperature and Level See Figure 1. Press and release the rubber button on the front face to display the temperature of the oil in the oil tank in degrees Fahrenheit (°F), and the oil level. The display will automatically shut off after approximately ten seconds. Do not overfill oil tank. Doing so can result in oil carryover to the air cleaner leading to equipment damage and/or equipment malfunction. (00190a) NOTES Oil level cannot be accurately measured: • on a cold engine • with the motorcycle upright • with the engine running NOTE Oil level on 2000 through 2004 Softail models with the original dipstick is checked with the motorcycle standing upright (not leaning on the jiffy stand). THIS IS NOT THE CASE with the LCD oil temperature/level dipstick. For all 2000 and later Softail models, oil level inspection must be done with the motorcycle LEANING ON the jiffy stand, on level ground. For pre-ride oil level inspection: With the motorcycle on level ground, RESTING ON the jiffy stand : •The oil level should be as indicated in Figure 1, display 4 through 8 (bars showing oil level, and “COLD OIL” message followed by flashing oil temperature) when the engine is cold. DO NOT ADD OIL to bring the level to the FULL mark on the dipstick of a COLD engine. •If the oil level indicates as in display 9 (animated level bars, followed by an “888 NO SENSOR” code), the wires inside the dipstick may be disconnected or damaged. Refer to Replacing the Battery later in these instructions to separate the dipstick upper and lower assemblies. If the small plug next to the battery has become dislodged from the receptacle, plug it in. If a visible wire is damaged, a repair can be attempted. If no damage is visible, the dipstick is damaged internally and should be replaced. For oil level inspection at operating temperature: Ride the motorcycle until the engine is at normal operating temperature. Idle for 1-2 minutes with the motorcycle on level ground, RESTING ON the jiffy stand (except Softails) , turn the engine OFF.

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION INSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit

Incoming search terms: