2006-2007 Honda TRX450R SR4 4 Stroke racing system INSTALLATION

0

Filed Under (Honda) by admin on 30-11-2011

download
Install Motoworks header pipe using stock nuts, finger tight at this point ( Fig 4) 2. Install Motoworks tailpipe with muffler using bolt and spacer supplied in kit on upper rear mount, use stock nut and bolt on lower mount finger tight at this point. (Fig 5 and 6) 3. Torque header pipe nuts to 1.0 kg-m ( 7.3 lb-ft ) 4. Torque tailpipe mounting bolts to 2.5 kg-m ( 18 lb-ft ) 5. Re-check all your work 6. We recommend that you clean the entire exhaust system with a mild detergent, i.e. glass cleaner prior to starting as any oily residue may cause permanent stainingBefore operating check for proper clearance between Motoworks exhaust and ATV i.e. frame, plastic, brake line, fuel line etc if problems exist re-check work

2002 Triumph Speed Triple 955i Standard Mount Slip-On Exhaust System Installation Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Loosen the clamp that holds the muffler connector pipe to the headers. 3. Remove the hardware that holds the stock muffler at the passenger footpeg bracket. Take off the muffler. 4. Place a bead of the hi-temp sealant on the outside edge of the header that goes into the s-bend. Wipe off the excess sealant that will squeeze out. Slide the S-bend connector pipe onto the end of the headers (wipe off the excess sealant that will squeeze out). Re-use the stock clamp to attach the s-bend to the headers. Leave loose for now. 5. Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 6. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need to twist and turn the S-bend a little to get it in the right place. Locate both tabs of the canister clamp and the 50mm spacer on the inside of the passenger footpeg bracket. Use the 85mm bolt and stock nut & washer to secure it. Leave loose for now. 7. Make sure everything is aligned and tighten all hardware. Affix the connector springs to the muffler. 8. Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness.

1999-2001 Triumph Sprint RS Slip-On Exhaust System Installation Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Loosen the clamp that holds the connector pipe to the headers under the bike. Remove the hardware that holds the stock muffler at the passenger footpeg bracket. Take off the muffler. 3. Re-using the stock Triumph clamp install the new S- bend. Leave loose for now. 4. Place a bead of the hi-temp sealant on the outside edge of the s-bend. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 5. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need to twist and turn the S-bend a little to get it in the right place. Place the spacer between the stock footpeg bracket and the tabs of the clamp. Locate both tabs of the canister clamp on the outside of the spacer. Use the hardware provided along with the stock nut to secure it. Leave loose for now. 6. Make sure everything is aligned and tighten all hardware. Affix the two connector springs to the muffler. 7. Be sure to allow the sealant to dry per the manufacture’s instructions before starting the bike . Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness.

KYMCO Super 8 150 Exhaust System with M-2 Canister Installation Instructions

0

Filed Under (Kymco) by admin on 26-10-2010

download
1.*Make*sure*the*bike*is*completely*cool*before*starting* the*installation.*Make*sure*the*bike*is*secure*on*a* centerstand*or*ideally*a*service*lift. 2.*Remove*OEM*exhaust*assembly. 3.*Attach*supplied*muffler*hanger*bracket*using*the* supplied*flange*bolts*and*tighten*to*15lbs-ft. 4.*Attach*TBR*header*to*muffler*using*the*X-ring*and*4* 6x14mm*bolts*with*lock*washers*provided,*leave*loose* for*now. 5.*Install*TBR*exhaust*to*scooter*keeping*the*OEM*exhaust* gasket*between*header*and*cylinder*head. 6.*Slide*rubber*lined*muffler*clamp*over*muffler*assembly* and*secure*to*bracket*using*supplied*8x20mm*bolt*and* nut. 7 .*Check*muffler*alignment*and*tighten*header*nuts*then* X-ring*bolts*and*finally*muffler*clamp*bolt. 8.*Before*you*run*the*bike,*clean*off*all*fingerprints*and* dirt,*as*any*oily*residue*will*etch*the*metal*and*become* somewhat*permanent*when*the*system*gets*hot.*Run* the*bike*and*enjoy.*It*is*normal*for*some*white*smoke*to* appear*the*first*time*you*start*the*bike.*This*is*packing/ manufacturing*oil*from*inside*the*pipe*burning*off.* Check*for*gaps*or*leaks.*If*you*find*a*leak,*a*little*high* temperature*silicon*sealant*should*fix*it.*After*50*to*100* miles,*recheck*all*fasteners*for*tightness. Qty.*Description* Part*Number 1* Muffler*Canister*M-2** Varies 1* Header* 005-27401H 1* Muffler*Clamp* Varies 1* HARDWARE*KIT* 005-274-3 2* *X-Ring* (half)* 005-7-2-3 1* *Long*Muffler*Mounting*Bracket* 005-274-B 1* *8mm*Flange*Nut* 005-FN8

Aprilia Mille And Mille R Exhaust System Installation Instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the sidestand or ideally a service lift. 2. Unhook the springs holds the stock canister to the headers under the bike. 3. Remove the hardware that holds the stock canister at the exhaust bracket. Take off the stock canister. 4. Install the new s-bend into the stock header. 5. Install VALE adapter kit using supplied kit instructions. 6. Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 7. Carefully slide the muffler clamp over the muffler. (Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need to twist and turn the S-bend a little to get it in the right place. Locate both tabs of the canister clamp on the outside of the exhaust bracket. Use the stock hardware to secure it. Leave loose for now. 8. Make sure everything is aligned and tighten all hardware. Reinstall the stock springs at the s-bend/header junction. Affix the two connector springs to the muffler. 9. Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness