YAMAHA FZR600 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Kawasaki) by admin on 27-04-2011

download
Front Axle and Outer Tube Front Wheel Axle Holder Rear Axle and Nut Handlebar Crown and Inner Tube Handlebar Crown and Steering Stem Steering ring nut (Upper and lower) Brake Caiiper (Front/Rear) Bleed Screw and Brake Caliper Brake Hose and Union Bolt Front Master Cylinder and Cylinder Cap Front Fender and Outer Tube Handlebar Boss and Front Fork Handlebar and Handlebar Boss Engine Mounting: Front ; Rear — Upper ; Rear — Lower 1 Down Tube and Frame: Front 1 Rear l Footrest Bracket and Frame I Pivot Axle and Nut Relay Arm and Frame Connecting Rod and Swingarm Connecting Rod and Relay Arm Rear Shock Absorber and Reiay Arm Rear Shock Absorber and Frame Footrest and Footrest Bracket I Rear Footrest Bracket and Frame Rear Master Cylinder and Rear Arm Bracket Cowling and Stay Compression Bar and Brake Caliper Bracket Front Fork Pinch Bolt: Upper Lower Sprocket and Clutch Hub Brake Disc and Clutch Hub Inner Tube and Steering Stem Frame and Rear Frame: Upper

KTM 4357/ 4860 MX Multi Adjuster WP Suspension manual Disassembly And Assembling

0

Filed Under (KTM) by admin on 13-02-2011

download
Disassembly forkleg 12_062 12_079Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 5 Frontfork 4357/4860 MXMA 02/2002 Clamp the forkleg (axle-clamp) in the vice and let the outer-tube down. Pull the spring downwards… …and place open-end spanner (size 22) on the hydraulic stop. Unscrew the screw-cap. 12_067 12_068 12_069 12_072Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 6 Frontfork 4357/4860 MXMA 02/2002 Remove the screw-cap from the piston- rod. 12_070 Remove the preload spacers. 12_074 Pull the spring downwards and remove the spanner. 12_075Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 7 Frontfork 4357/4860 MXMA 02/2002 Remove the spring. 12_076 Remove the adjustment tube with the O-ring. 12_089
Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 8 Frontfork 4357/4860 MXMA 02/2002 Clamp the axle-clamp in the vice so that the forkleg is at an angle of ±45 degrees. 12_095 Unscrew the compression holder out of the axle-clamp. (size 19) (when the cartridge is rotating with the holder, bend the piston- rod a little bit to the side) 12_096 Drain the oil out the forkleg. 12_094 Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 9 Frontfork 4357/4860 MXMA 02/2002 Remove holder compression. Caution: oil iscoming out the cartridge. Disassemble the cartridge out the forkleg. 12_097 12_098 12_099 Disassemble the dust-wiper

Incoming search terms:

Suzuki B-King GSX1300 BK Suspension Removal and Installation

0

Filed Under (Suzuki) by admin on 01-12-2010

download
Front Fork Removal and Installation B823H12206002 NOTE The right and left front forks are installed symmetrically and therefore the removal procedure for one side is the same as that for the other side. Removal 1) Remove the front wheel assembly. Refer to “Front Wheel Assembly Removal and Installation in Section 2D (Page 2D-4)”. CAUTION ! •Make sure that the motorcycle is supported securely. •Do not operate the front brake lever with the front wheel removed. 2) Disconnect the brake hose clamp (1) from the front fender. 3) Disconnect the brake hose (2) from the brake hose clamp. 4) Remove the front fender by removing the bolts (3) , left and right. 5) Remove the reflex reflector for E-03, 24, 28, 33. 6) After removing of the headlight cover upper screws (4), move the headlight assembly forward. 7) Loose the front fork upper clamp bolt (5). NOTE •Slightly loosen the front fork cap bolt (6) to facilitate later disassembly. •Be sure to adjust the rebound damping force adjuster (7) to the softest position before removing the front fork. 8) Loosen the front fork lower clamp bolts (8) and remove the front fork. NOTE Hold the front fork by the hand to prevent sliding out of the steering stem. Installation 1) Set the front fork to the front fork lower bracket temporarily by tightening the lower clamp bolts (1) . 2) Tighten the front fork cap bolt (2) to the specified torque. Tightening torque Front fork cap bolt (a): 23 N·m (2.3 kgf-m, 16.5 lb-ft) 3) Loosen the lower clamp bolts. 4) Set the front fork with the upper surface “T” of the outer tube positioned 3.0 mm (0.12 in) “a” from the upper surface of the steering stem upper bracket. 5) Tighten the front fork lower clamp bolts (1). Tightening torque Front fork lower clamp bolt (b): 23 N·m (2.3 kgf- m, 16.5 lb-ft) 6) Tighten the front fork upper clamp bolt (3). Tightening torque Front fork upper clamp bolt (c): 23 N·m (2.3 kgf- m, 16.5 lb-ft