2001-2010 Harley-Davidson TCFI III Fuel Injection System Installation And Tuning Manual

0

Filed Under (Harley Davidson) by admin on 06-04-2012

download
1. Check the exhaust system. If you can insert a broomstick through the mufflers, you have the equivalent of open drag pipes and auto-tuning will fail. If applicable, read the section about exhaust considerations starting on page 11. 2. Check for updates. This tuning manual is for TCFI III units with revision 3.3 or higher firmware. Before proceeding, check our website at www.daytona- twintec.com for available updates for the TCFI firmware, accompanying PC based software, and documentation. 3. Tech support. If you have questions or encounter problems at any point during the installation process, please contact our tech support at 386- 304-0700. 4. USB interface. Read the USB interface instructions starting on page 17, install the USB drivers and configure the COM port. 5. PC Link software used for setup and engine tuning. Read the PC Link TCFI III instructions starting on page 19 and install the software. 6. Data logging software. Read the TCFI III Log instructions starting on page 34 and install the software. 7. TCFI Controller. Read the TCFI installation instructions starting on page 41 and install the TCFI unit. Make sure you install the green PC link jumper wire. 8. WEGO wide-band exhaust gas oxygen sensor interface. Read the WEGO installation instructions starting on page 42, install the WEGO unit and perform the free air calibration described on page 43. 9. Connect the USB interface cable between the TCFI unit and your PC. 10. Start the PC Link TCFI III software, use the Open File command, and open the appropriate setup file. Setup data files are provided in the program folder for typical engine applications. Refer to Table 3 on page 16 for details. Additional setup guidelines for aftermarket throttle bodies and larger displacement engines are given on page 9. 11. Use the Edit Basic Parameters command. Make any required changes such as estimated rear wheel horsepower, injector flow rating (refer to Table 1 on page 9), and RPM limit. You must set the vehicle speed sensor (VSS) frequency for your model. This affects speedometer/odometer scaling, idle RPM control, and turn signal

Incoming search terms:

HARLEY-DAVIDSON DYNA BIGSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-03-2012

download
1. Remove seat to gain access to rear oxygen sensor connector. Unplug sensor and feed end of wire through frame so that it is free from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Remove two bolts holding rectifi er onto front of frame (near front tire). Open plastic cover to gain access to front oxygen sensor connector. Unplug sensor from harness. Remove cable tie holding wire to frame and feed end of wire through so that it is free from motorcycle. 3. Loosen heat shield clamps on both the front and rear head pipes. 4. Remove two cylinder exhaust port fl ange nuts from each head pipe, located at the cylinder head. 5. Remove front head pipe clamp bolt. 6. Remove the bolt that attaches muffl ers to the frame mounting bar. 7. Remove the complete exhaust system and set aside. Assistance may be required. 8. Remove stock mounting bar and the studs in the transmisson cover. Save the bolts, one will be re-used. 9. Remove left bolt below the transmission cover. Position mounting bracket 390-P over mounting location to determine which bolts to remove (Figure 1). Install this bolt in the top hole left vacant by the new bracket. 10. Carefully remove the fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check condition of stock exhaust gaskets. Replace if worn or damaged. (Recommended replacement exhaust port gaskets, Screamin’ Eagle part number 17048-98). 11. Remove stock oxygen sensors, they will be re-used on new system

HARLEY DAVIDSON DYNA SIDESHOTS BLACK INSTALLATION AND REMOVAL PROCEDURE

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove seat to gain access to rear oxygen sensor connector. Unplug sensor and feed end of wire through frame so that it is free from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Remove two bolts holding rectifi er onto front of frame (near front tire). Open plastic cover to gain access to front oxygen sensor connector. Unplug sensor from harness. Remove cable tie holding wire to frame and feed end of wire through so that it is free from motorcycle. 3. Loosen heat shield clamps on both the front and rear head pipes. 4. Remove two cylinder exhaust port fl ange nuts from each head pipe, located at the cylinder head. 5. Remove front head pipe clamp bolt. 6. Remove the bolt that attaches muffl ers to the frame mounting bar. 7. Remove the complete exhaust system and set aside. Assistance may be required. 8. Remove stock mounting bar and the studs in the transmisson cover. Save the bolts, one will be re-used. 9. Remove left bolt below the transmission cover. Position mounting bracket 405-P over mounting location to determine which bolts to remove (Figure 1). Install this bolt in the top hole left vacant by the new bracket. 10. Carefully remove the fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check condition of stock exhaust gaskets. Replace if worn or damaged. (Recommended replacement exhaust port gaskets, Screamin’ Eagle part number 17048-98)

1993 – 2008 Applicable Models ENGINE BANK 1 AND BANK 2 A/F AND O2 IDENTIFICATION

0

Filed Under (Toyota Manuals) by admin on 25-10-2011

download
This service bulletin provides information on the proper identification of engine bank 1 and engine bank 2 for correct A/F sensor and oxygen sensor replacement. This bulletin contains information that identifies engine bank 1 and engine bank 2 on the following engines: 1AZ-FE, 2AZ-FE, 2AZ-FE (PZEV), 1GR-FE, 2GR-FE, 2GR-FSE, 2JZ-GE, 1MZ-FE, 3MZ-FE, 1UR-FSE, 3UR-FE, 2UZ-FE, 3UZ-FE, 5VZ-FE, and 1ZZ-FE. Bank 1 (B1) refers to the bank that includes cylinder No. 1. Bank 2 (B2) refers to the bank opposite bank 1. Sensor 1 (S1) refers to the sensor that is located before the catalytic converters. Sensor 2 (S2) refers to the sensor that is located after the catalytic converters

2001 Honda GL1800 Oxygen Sensor Replacement Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
REPAIR PROCEDURE 1. Remove the top shelter (see page 2-10 in the Service Manual). 2. Remove the left and right O 2 sensors from the exhaust pipes. • You do not have to remove the exhaust pipes to remove the O 2 sensors. • Be sure to note the wire routing for proper reassembly. 3. Install the new O 2 sensors and route the wires properly (see pages 1-33 and 1-34 in the 2001- Service Manual). 4. Connect the black 4P female coupler of the sub- harness kit to the wire harness side black 4P male coupler (for the left-side O 2 sensor). 5. Connect the new left O 2 sensor to the black 4P coupler on the sub-harness. 6. Route the sub-harness from left to right, across the front edge of the fuel tank and secure it with the clip on the cruise actuator 7. Cut off the right 4P male O 2 sensor coupler (on the wire harness side). 8. Install a PVC cap onto the end of the Black/yellow wire and Green/red wire (these are the wires that were connected to the coupler that was removed in step 7). Fold each cap back and tape it securely to its wire; these wires are no longer used. • Do not cut the wires off, just tape them back. • The tape is supplied in the replacement kit. 9. Strip the ends of the White and Black/red wires (which were connected to the coupler that was removed in step 7) on the wire harness side and the 2P coupler on the sub-harness. Install a heat shrink tube on each wire of the sub harness. 10. Twist the ends of the White and Black/red wires of the sub-harness 2P coupler to the White and Black/red wires of the main harness. 11. Solder the wires using the solder from the kit. 12. Use a heat gun to secure the heat-shrink tubing over the soldered wires. 13. Connect the right O 2 sensor coupler to the white 4P male coupler on the sub harness.

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

Incoming search terms:

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

HARLEY DAVIDSON CHROME SEAT POST REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
REMOVE 2 1 is00000 1. Seat Post 2. Screw Figure 2. Lower Seat Post 1. Refer to Owners Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery negative cable. 3. On motorcycles equipped with oxygen sensors, disconnect the rear sensor connector. 4. See Figure 2. Remove screw (2) and washer from the lower seat post (1) and discard. -J04294 1 of 2 5. Disconnect spark plug wires and primary wire from ignition coil. 6. See Figure 3. Loosen the bracket screws (1). Remove seat post screw (2) and seat post with ignition coil and cover. 7. See Figure 4. Remove coil cover screw (5) and cover (4) from stock seat post (1). 8. Remove ignition coil screws (3) and coil (2) from seat post. 2 1 is04241 1. Bracket Screws 2. Upper Seat Post Screw Figure 3. Upper Seat Post Fasteners 2 5 1 3 4 is04337 1. Seat Post 2. Ignition Coil 3. Coil Screw 4. Coil Cover 5. Coil Cover Screw Figure 4. Install Ignition Coil to Seat Post INSTALL 1. See Figure 4. Install ignition coil (2) to new seat post using screws (3). Tighten ignition coil screws to 10-15 ft-lbs (13.6-20.3 Nm) . 2. Install coil cover (4) to seat post with screw (5) and tighten to 30-40 in-lbs (3.4-4.5 Nm) . 3. See Figure 1. Place seat post (1) in position and attach lower post with screw (2), washers (3) and dome nut (4). Tighten screw (2) to 10-15 ft-lbs (13.6-20.3 Nm) . 4. See Figure 3. Attach upper seat post with screw (2). Tighten screw (2) to 12-15 ft-lbs (16.2-20.3 Nm) . Tighten bracket screws (1) to 12-15 (16.2-20.3 Nm) . 5. Connect primary wire to ignition coil. 6. Connect spark plug wires to ignition coil. The rear cylinder plug wire attaches to the top coil post. Ensure that spark plug wire boots are fastened securely. 7. Connect rear oxygen sensor connector, if equipped. 8. Reconnect battery negative cable

Incoming search terms:

2001 GL1800 Oxygen Sensor Replacement / REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the top shelter (see page 2-10 in the Service Manual). 2. Remove the left and right O 2 sensors from the exhaust pipes. • You do not have to remove the exhaust pipes to remove the O 2 sensors. • Be sure to note the wire routing for proper reassembly. 3. Install the new O 2 sensors and route the wires properly (see pages 1-33 and 1-34 in the 2001- Service Manual). 4. Connect the black 4P female coupler of the sub- harness kit to the wire harness side black 4P male coupler (for the left-side O 2 sensor). 5. Connect the new left O 2 sensor to the black 4P coupler on the sub-harness. 6. Route the sub-harness from left to right, across the front edge of the fuel tank and secure it with the clip on the cruise actuator

RIVCO POWERMASTER EFI MODULE Installation AND Tuning Manual

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Locate the fuel injectors and their connectors on the intake manifolds between the “V” of the engines cylinders. You may remove the fuel tank to gain easy access to the plugs or you can make the connections with the tank on as follows. Remove the rear fuel tank mounting bolt and loosen the front two bolts. Lift the rear of the tank as high as possible (2-3 inches) and place a piece of wood between the tank and frame to hold the tank up. 2. Mounting the POWERMASTER™ EFI Module. While you can mount the module most anywhere it is recommended to mount it under the right hand side cover for easy access when making adjustments. Find a suitable surface to mount the Velcro Adhesive Square supplied. Clean the surface with rubbing alcohol, peel the backing and press firmly in place. Press the Module onto the Velcro. Route the wires with the plugs for the injectors between the frame rails and up toward the injectors with the other wires located on the backbone of the frame. If yours is a model with wires and plugs for the oxygen sensors route these wires downward with the short lead going to the plug on the rear exhaust pipe (about 6″ from the cylinder head) and the longer following along the right frame tube under the engine and forward to the front oxygen sensor and its plug.3. Connect the wires to the injectors under the fuel tank as follows. Unplug the bike’s wire harness from the injectors. Connect the male and female connectors from the injectors and the wire harness to the RIVCO POWERMASTER™ EFI Module. This places it electrically between ECU and the injectors. Repeat this process for each injector. NOTE it does NOT matter which lead goes to which injector.

Incoming search terms: