HARLEY DAVIDSON DETACHABLE PASSENGER BACKREST LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
INSTALLATION 1. See Figure 1. If not already assembled in package, assemble V-logo onto each mounting bracket (2 and 3) using #4-40 thread-forming screws (5). 2. Position luggage rack between sideplates of detachable passenger backrest assembly. 3. Thread button head screws (7) through washers (6), then through holes in luggage rack support and passenger backrest sideplate and into mounting brackets (2 and 3). Apply LOCTITE 243 (Blue) to screws (7) before installation. Finger tighten. 4. Tighten button head screws to 19 ft-lbs (26 Nm) . NOTE The backrest shown in Figure 1 is not included in this kit and must be purchased separately. -J01851 1 of 2 SERVICE PARTS 8 1 7 6 3 2 4 5 is04290 Figure 1. Service Parts: Detachable Passenger Backrest Luggage Rack Kit Table 1. Service Parts Table Part Number Description (Quantity) Item Part Number Description (Quantity) Item 2711 Screw, #4-40 thread-forming, steel, zinc plated (4) 5 Not sold separately Passenger backrest rack kit 1 94066-90T Washer, chrome (4) 6 53046-00 Bracket, mounting, right side (includes items 4 and 5) 2 94392-92T Button head screw, hex socket, chrome (4) 7 53045-00 Bracket, mounting, left side (includes items 4 and 5) 3 Not Sold Separately Warning label 8 Not sold separately V-logo (2) 4

Incoming search terms:

HARLEY DAVIDSON MOUNTING BRACKET SERVICE MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
INSTALLATION 1. See Figure 1. Note position of mounting brackets (1). Remove old mounting brackets and discard. NOTE On 1997-2000 models, the air fittings are installed to the two mounting holes on the right-hand right side bracket. On 2003 and later models, the single air fitting is installed to mounting hole on the left-hand side bracket. 2. See Figure 2. Install new mounting brackets from kit on each side of the motorcycle using new locknuts as follows: a. Use the 5/16-18 x 1 inch screws (5) in the upper two holes with 2 chrome washers (3) placed between the mounting bracket and the saddlebag support at each of the two locations. Install a 5/16-18 flange locknut (2) behind the screw that does not screw into a weld nut. Tighten to 15-19 ft-lbs (20-26 Nm). b. On each side, install a 1/4-20 x 7/8 inch screw (9) through the bottom hole of the mounting bracket and the saddlebag bracket as shown, with a chrome washer (3) placed between the mounting bracket and the saddlebag bracket. Tighten to 10-14 ft-lbs (13.5- 19.0 Nm). On 1997-2002 models, install the air line fittings to the lowest two holes drilled in the right side bracket. On 2003 and later models, install the single air line fitting to the lower front hole drilled on the left side bracket. c. See Figure 2. On each side, attach docking points (6) in their proper location on mounting bracket with 3/8- 16 x 1-1/2 in. buttonhead screws (7), washers (3) and locknuts (8) but leave locknuts slightly loose so docking points can be adjusted for proper fit. On 1997and later models, the docking point will attach through the front hole of the mounting bracket as shown. On 1994-1996 models, the docking point will attach through the rear hole of the mounting bracket. d. Place detachable passenger backrest into docking points as described in the Backrest Instruction Sheet. Make sure that the forward notches of the sideplates are pushed completely into the forward docking points, then tighten the rear docking points securely to 45-47 ft/lbs (61.0-64.0 Nm

Incoming search terms:

HARLEY DAVIDSON CONTOURED TOUR-PAK LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION NOTE The location of the Tour-Pak spoiler has a direct relationship to the location of Tour-Pak mounted luggage rack. The spoiler template will locate the Tour-Pak spoiler in the correct position for the luggage rack so that the spoiler may be added in the future. It is recommended that the spoiler be installed first. See Figure 1. 1. Identify if the installation of a Tour-Pak mounted spoiler is desired in the future. Use the template if the spoiler will be installed. Cut the template along the appropriate line. Carefully place template on top of Tour-Pak lid, aligning edges of template with top surface of Tour-Pak. Tape template in desired location. 1 is 00579 1. Check clearance between rack and spoiler Figure 1. Tour-Pak Rack and Spoiler NOTE Position top rack with upright section toward rear of motorcycle. To avoid contact with the passenger backrest pad, do not mount the top rack in too far forward a position. 2. See Figure 2. Place the four mounting pads (1) onto the four mounting supports on top rack (2). Carefully center the rack on the lid and position the rack rear supports 5/8 inch to 3/4 inch (16 mm to 19 mm) in front of the emblem on the Tour-Pak lid, as shown. 1 is 00636 1.5/8 in. – 3/4 in. (16 mm – 19 mm) Figure 2. Locate Holes From Emblem 3. Use a grease pencil to temporarily mark the positions of the four mounting pads on Tour-Pak cover. NOTE Apply masking tape to the Tour-Pak cover painted surface at the four points where the top rack mounting holes will be drilled. The tape can be marked for hole location, and will help prevent the paint from being chipped during the drilling procedure. 4. Carefully remove top rack/mounting pad assembly. Place a strip of masking tape over each grease pencil mark on the Tour-Pak cover. Once again, position top rack/mounting pad assembly on Tour-Pak cover in the desired mounting location. 5. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting pad. Remove top rack/mounting pad assembly. Use a ruler to mark the exact center of each circle drawn on the tape strips. NOTE Remove all contents from within the Tour-Pak to avoid possible contact with the moving drill bit during the following drilling procedure. 6. Drill starter holes using a 1/16 inch drill bit. Drill the finished holes for the mounting screws using a 9/32 inch drill bit. Remove masking tape strips. 7. Apply a small amount of silicone sealant around each mounting hole on interior surface of Tour-Pak cover

Incoming search terms:

HARLEY DAVIDSON PASSENGER PILLION UPRIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION 1. See Figure 1. Install the luggage rack following the instructions in the kit. 2. Insert the ends of the upright (2) into the pillion (3) (purchased separately) and align the holes in the upright with the holes in the pillion. 3. See Figure 2. Apply LOCTITE 243 to screws (2) and install with washers. Tighten screws to 84-108 in-lbs (9.5-12.2 Nm) . 4. Install the pillion and upright assembly onto the luggage rack following the instructions in the detachable passenger pillion kit. 1 2 3 4 is05507 1. Passenger backrest pad (optional) 2. Passenger pillion upright 3. Detachable pillion (purchased separately) 4. Luggage rack (purchased separately) Figure 1. Upright SERVICE PARTS 3 1 2 is05508 Figure 2. Service Parts: Passenger Pillion Upright Table 1. Service Parts: Passenger Pillion Upright Kit Part Number Description (Quantity) Item Not Sold Separately Passenger pillion upright 1 3787 Screw, 1/4-20 x 0.75 inch (4) 2 6703

Incoming search terms: