2004 Kawasaki ZX10R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
Remove the main seat and the passenger seat 2. Remove the tail cover by removing the two bolts. 3 Place the Power Commander in the tail section and route the wiring harness on the inside of the tail section towards the front of the bike (Fig. A). 4. Remove the fuel tank. 5. Remove the air box lid by removing the 8 screws around the outer edge (Fig. B). 6. Remove the bolts shown in Fig. C. This will allow you to remove the air box. Fig. A Fig. B Fig. C i212-411 2004-2005 Kawasaki ZX10R – PCIII USB – 2 i212-411 www.powercommander.com Remove these bolts Remove screws Remove bolts 7. Locate the Throttle Position Sensor connector. This connector is located above the left hand side of the engine. This is a white 3 pin connector. Unplug this connector (Fig. D). 8. Plug the white connectors from the PCIII in-line of the stock TPS connector (Fig. E). 9. Locate the fuel rail connector behind the injector bodies (Fig. F). This connector is brown in color

Harley- Davidson FX/ FL Big Twin 1965-1984 Two-Piece Seat Mounting Suggestions

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
Stock One-Piece Seat Removal Steps 1. Remove rear fender screw located behind the passenger seat and set aside. The stock rear fender screw will be used to attach your new Mustang Two-Piece Seat. 2. Slide seat back and up. Mounting of Mustang Solo & Passenger Seat 1. Remove two screws from back of Mustang solo seat. 2. Align two chrome tabs located at the front of the passenger seat with the mounting holes in back of solo. 3. Screw rear seat and solo together. 4. Slide solo front forks under frame. 5. Align chrome rear tab located at back of passenger seat with stock hole in fender. 6. Secure in place with stock fender screw to complete the installation process. Note: Use of side brackets optional and would use the rubber expansion plugs, threaded inserts, and bolts used for a solo only installation.

2006 – 2007 Harley-Davidson Softail Ultimate seats Installation Manual

0

Filed Under (Harley Davidson) by admin on 04-04-2012

download
1. Remove original seats from your bike. #2. Your new Ultimate seats install using the front seat side mount bolts and the passenger seat is bolted to the front seat and rear fender. Side mount hex nuts = 2. If your stock rider seat is a rear fender mount, install one of the hex nut inserts on each side of the frame if they are not in your bike frame already. #3. All the mounting brackets are already installed on your new seats. #4. Connect our passenger seat to the rider seat with the 2 new round head allen bolts ( 1/4″ x ¾”) #5. Use the 2 new supplied bolts to attach the rider seat to the bike frame, one on each side into the threaded inserts ( 1/4″ x ½”) pan Phillips head) #6. Use the other new bolt for the passenger seat rear bracket in the fender (1/4″ x ½”) pan head. Enjoy the ride again

Incoming search terms:

Suzuki GSX-R 1000 AFR Tuner INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 20-02-2012

download
The installation of the AFR Tuner should be done by experienced technicians only. Always disconnect the battery from the motorcycle before making any modification to the wiring harness. Remove the negative terminal from the battery before starting the installation work. The quality of the installation work greatly affects the reliability of the AFR Tuner and the motorcycle. Work precisely and very carefully when modifying the wiring harness of the vehicle. Always double check that the wire you are about to cut or tap into is the correct one. The ECM or the AFR Tuner can be destroyed by a faulty installation. 3.2. Installing the AFR Tuner to the wiring harness 3.2.1. Main cable The AFR Tuner connects to the motorcycle through its Main connector . Figure 2 shows the wiring diagram and the necessary modifications, which needs to be made when installing the unit into the fuel injection system of the motorcycle. Information about the ECM terminal numbers and wire colors for some popular motorcycles can be found in Chapter 6 . The best location for installing the AFR Tuner main unit is at the passenger seat area of the motorcycle mounted in the trunk space or on the subframe under the fairing, as this place provides protection from engine heat and the weather. Electrical contact between the metal casing of the AFR Tuner and the rear subframe must be prevented by using insulating material, such as the included self adhesive velcro strips. If necessary use some cable ties to secure the unit in place. The installation of the AFR Tuner into the wiring harness involves tapping into some wires and cutting others while connecting the two ends to the AFR Tuner. The harness modifications are best done near the ECM, since most of the wires can be found there. Part of the wiring modifications are related to connecting the AFR Tuner in-line between the ECM and the fuel injectors. In such cases when the motorcycle is equipped with primary and secondary injectors the AFR Tuner has to be installed on the primary injectors, which operate under all engine conditions. Correct grounding of the AFR Tuner is very important for electrical noise reduction. The above mentioned insulation of the metal case from the motorcycle frame is necessary for the same reason, which is to avoid the forming of a ground loop. An even more important requirement is the correct connection of the three ground wires of the AFR Tuner. As shown on Figure 2 , these three wires must be led out separately to the ECM and connected together at same point where the ECM ground wire is tapped into. This point should be as close to the ECM terminal as possible. For best quality of the electrical contacts all connections should be done by soldering and covering the exposed part of the wire with heat shrink tubing. For reliability reasons do not use clip on type wire taps

SUZUKI GSX-R1300 / HAYABUSA Fuelpak Connectors INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-02-2012

download
Remove the main seat and passenger seat. 2. Use a prop to hold the tank up in the trunk area. 3. Disconnect the main wiring harness from each of the lower injectors. (Fig 1) 4. Lay the Fuelpak unit in the tail section and route the wire harness down the left side of the motorcycle toward the throttle bodies. 5. Plug the Fuelpak wiring harness in line of the stock wiring harness and injectors. (Fig 2) 6. Locate the throttle position sensor connector on the right hand side of the throttle body. 7. Install the Fuelpak wiring harness TPS connectors in line of the stock wiring harness. (Fig 3) 8. Attach ground wire to the negative side of the battery. 9. Install Fuelpak in the tail section using the supplied velcro. (Fig 4) 10. Bolt the fuel tank back into place. INSTALLATION INSTRUCTIONS FOR P/N 62009 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION

Honda VTX 1800 Motorcycles Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 19-12-2011

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) . · Passenger Seat and mounts (to be reinstalled without modification) . NOTE: OEM front and rear seat mounting bolts to be retained and reused. · Left and right passenger foot rests and mounts (to be reinstalled with modification) . · Mufflers (to be re-installed and relocated with minor modification) . · Rear Fender (complete w/ sub frame and all attaching parts) . · Swing Arm, Drive Shaft and Rear Wheel (complete w/ brake line and all attaching parts) Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Use 17/64″ drill and drill through frame from inside out using passenger footrest mount holes as guide. b. Enlarge the passenger footrest mounting holes on the left and right side of the frame to 27/64″. c. Enlarge the holes in the left and right passenger footrest mounting plates to 27/64″. d. Clean area of all debris. 3.2 Relocate Regulator a. Install supplied “Z” bracket to the regulator as shown using the supplied hardware. b. Attach regulator to frame using the supplied hardware. c. Tie hoses down to avoid contact with the swing arm. Qty Description 1 ¼-20×2 hex head bolt 1 ¼-20×1-1/4 hex head bolt 6 ¼-20 Nyloc nut 10 1/4- SAE flat washer 4 as spacers 3.3 Hose Stay a. For models that have a recover tank below the swing-arm, a holder has been included keep the hose connected to the water pump away from the champion swing-arm. b. Remove the hose from the top of the recovery tank. c. Push the water pump hose forward against transmission. d. Secure hose with supplied stay as shown using existing bolt. Ensure that hose is not being crushed. Bend stay if necessary. e. Reconnect hose to recovery tank

Honda CBR 600 F4i 2004 – 2005 Bestem USA Fiberglass F13 Installation Guide

0

Filed Under (Honda) by admin on 20-11-2011

download
We highly recommend having a professional install this undertail. A dremel tool or nsimilar is what we found the best to cut plastics. Place bike on a rear wheel center stand. Remove passenger seat and hardware which secure stock undertail section Unplug the harness that connects tail light and remove the stock undertail. Position Bestem undertail close to the bike and determine the amount of plastic needs to be cut out. Use a dremel tool to carefully trim off plastics (glove boxes etc). This is the most time consuming part of the installation but your patience will be paid off. 5) Once the new undertail is slide in, determine holes need to be drilled (only on
certain models). Reuse the hardware for the stock undertail to secure the new undertail. 6) The wiring color codes from two round tail lights are Black Wire – Ground, connects to Ground wire. Red Wire – Brake Light, connects to brake light. Blue Wire – Running Light, connect directly to the running light. Orange Wire – Turn Signal, connect them to your L/R turn signal wires We highly suggest you solder the connections and use heat shrink wrap to seal the connections. Test your lights before going out for a ride, also make sure your new undertail is securely installed on the bike. Now it’s time to go out for a spin!

Incoming search terms:

2007 HONDA CBR600RR DUAL OUTLET SLIP-ON EXHAUST INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 07-11-2011

download
Make sure the motorcycle is cool and place securely on a service lift or stand. 2) Remove the two bolts securing the rider seat to the motorcycle. Remove the seat. See Figure #1 3) Using the key, remove the passenger seat. 4) Remove the bolts and push pin fasteners securing the tail section to the sub frame. Carefully spread the tail section and remove it from the motorcycle. See Figur ) Disconnect the turn signal & tail light plugs on the left side of the sub frame. 6) Remove the four bolts securing the complete rear fender assembly (including the tail light & turn signals) and the rear reflectors to the sub frame. Remove from the motorcycle. See Figure #2 7) Remove the two nuts from the back side of the reflectors and retain to be used elsewhere in Step #38. 8) Remove the two bolts securing the right side passenger peg. Remove the passenger peg. See Figure #4 9) Remove the bolt from the inside of the stock s-bend heat shield located behind the rear brake reservoir. See Figure #5 10)Remove the bolt securing the silver plastic heel cover from the right side rider peg mount. Remove the cover. See Figure #6 11)Remove the bolt securing the rear brake reservoir to the sub frame. Allow the reservoirto dangle

2004 – 2005 Camry, Highlander, And Solara, 2005 Matrix & Corolla PASSENGER AIRBAG INDICATOR LAMP

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
passengers weighing approximately less than 100 pounds, depending on their seating position. It is important for the front seat passengers to know that proper operation of the advanced frontal airbag system is highly dependent on the pressure placed on the seat bottom. Situations that add or subtract sensed weight can result in occupant misclassification. To minimize this situation: Check seating posture. Passengers should be seated upright with their back against the seat back and feet on the floor. Check loading conditions. Extra weight from items, such as bags or groceries or toys, hanging on the seat back can add to the sensed weight of the front seat passenger. A rear seat passenger lifting the front seat with their legs, objects placed under the front seat, or the front seatback in contact with the rear seat can subtract from the sensed weight of the front seat passenger. If the passenger airbag indicator lamp continues to switch ON to OFF after checking the above conditions, perform the following repair procedure. NOTE: The safest place for children is in the rear seat. Please note that Toyota recommends that you never install a rear-facing child restraint in the front passenger seat, even if the passenger “Airbag OFF” lamp is illuminated. Please refer to you Owner’s Manual for additional details. 2004 – 2005 model year Camry, Highlander, and Solara vehicles produced BEFORE the Production Change Effective VINs shown on the following page. 2005 model year Matrix and Corolla vehicles produced BEFORE the Production Change Effective VINs shown on the following page

Incoming search terms:

HARLEY DAVIDSON V-ROD CHROME REAR TURN SIGNAL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Prepare the Motorcycle 1. Remove the right cover and the maxi-fuse. 2. Follow Service Manual instructions to remove the air box cover. Remove the Existing Rear Turn Signals 1. For 2006 and Earlier Models: See Figure 1. Insert a screwdriver into middle of hole of license plate light cover. Push forward to release tail lamp housing retaining clip. 2. See Figure 3. Identify the white left [19] (1) and black right [18] (2) 2 pin rear turn signal connectors. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. To remove the rear turn signal wires from the socket terminal housing, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. 6. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 7. Repeat for the opposite turn signal. 1. For 2007 and Later Models: See Figure 2. Open seat and remove the nut and washer (3), seat post (2), passenger pillion and passenger seat (1) per the instructions in the Service Manual. 2. See Figure 4. Identify the left (1) and right (2) rear turn signal wires and 6 pin rear turn signal connector [94]. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. See Figure 5. Remove the turn signal wires from the 6 pin socket terminal housing. To remove the wires, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. Repeat for all four turn signal wires. Do not remove the license light wires from the socket terminal housing. 6. Gently pull the loose turn signal wires through the sheath toward the rear of the vehicle until completely removed from the sheath. 7. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 8. Repeat for the opposite turn signal

Incoming search terms: