HARLEY DAVIDSON NOSTALGIC BRAKE PEDAL PAD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
This kit is designed for use on the following model motorcycles: 1980 and later FLHT, FLT, FLHR, FLHS 1986 and later FLSTC, FLSTN, FLSTF, FLSTS. Each kit contains: QTY DESCRIPTION PART NO. 1 Brake pedal cover 44249-96 1 Rubber tread 44251-96 1 Bolt (with rubber H-D logo) 44229-95 1 Washer, 7/8 in. OD 6422 1 Washer, 5/8 in. OD 6316HW 1 Offset washer 6421 1 Acorn nut 7946 All Service Parts are listed above. Installation 1. Remove previously installed brake pedal cover from motorcycle. 2. Align and place brake pedal cover over rubber tread. 3. Insert bolt, with rubber logo properly aligned, into hole in combined new brake pedal cover and rubber tread. 4. Place 5/8 in. OD flat washer onto bolt first, followed by 7/8 in. OD washer. 5. Place new brake pedal cover and bolt/washer assembly on brake pedal. 6. Place offset washer on bolt. 7. Adjust and hold offset washer in position covering exposed slot under brake pedal and attach acorn nut to bolt. Tighten acorn nut to 25-29 ft-lbs

HARLEY DAVIDSON FL SOFTAIL REAR BRAKE LEVERS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2011

download
REMOVAL 1. See Figure 1. Remove the cotter pin (5) and washer (E) from the master cylinder clevis pin (B). Discard the cotter pin. NOTE The clevis pin has a slight interference fit. It may be necessary to use pliers to pull the clevis pin from the push rod. Be careful not to damage mating parts. 2. Remove the clevis pin (B) from the brake rod. Thoroughly clean and examine parts for wear. Replace if necessary. 3. Remove the brake lever mounting screw (A) and flat washer (D), and save for reinstallation, if necessary. Remove and discard the outer O-ring (2). 4. Remove the brake lever by rotating counter-clockwise and lifting the master-cylinder clevis if necessary. Pull the lever from the shaft. Remove and discard the inner O-ring. 5. Thoroughly clean the lever mounting shaft of grease and dirt. INSTALLATION NOTE These levers are equipped with self-lubricating bushings. It is not necessary to lubricate the mounting shaft or bushings inside the lever prior to installation. 1. See Figure 1. Insert the new O-rings (4) on either side of the lever bushings (2). Install the new brake lever (1) onto the mounting shaft. NOTE There is insufficient clearance to install the clevis pin from the outside, so it must be installed from the inboard side of the brake lever. 2. Align the holes in the lever and brake rod and insert the stock clevis pin (B) from the inboard side. 3. Install the small flat washer (E) onto the clevis pin and insert the new cotter pin (5). 4. Place the large flat washer (D) onto the brake lever mounting screw (A). Apply Loctite 243 (blue) to the threads of the screw, and reinstall into the brake lever mounting shaft. Tighten the screw to 12-16 ft-lbs (16.3-21.7 Nm) . 5. Install the brake pedal pad (C) to the brake lever. After repairing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) 6. Check the brake lever for proper operation and clearance through its full travel

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

HARLEY DAVIDSON SKULL BRAKE PEDAL PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation 1. Remove previously installed brake pedal cover from motorcycle. 2. Position new brake pedal chrome cover (1) over brake pedal pad (2). Large Brake Pedal 3. Align assembled brake pad (items 1, 2, and 5) from kit to brake pedal and insert and tighten screw (4) through the washer (3), and into the chrome cover (1). 4. Tighten screw to 19 ft-lbs (26 Nm). Small Brake Pedal 5. Align and install new cover and pad. Insert screw (4) through the washer (3), brake pedal and into brake pedal pad (2). 6. Insert the screw (4) and washer (3) into the chrome cover. 7. Tighten screw to 33 in-lbs (2.5 Nm)

HARLEY DAVIDSON IRONSIDE BRAKE PEDAL PAD INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION 1. Remove the previously installed brake pedal cover from the foot brake lever. 2. See Figure 1. Obtain the mounting plate (7) from kit. Position the mounting plate over the brake pedal (A) aligning raised area under plate with oval hole in brake pedal. 3. Obtain the offset washer (2) from kit. Position washer under brake pedal and align the “offset” area of the washer so that it covers oval hole in brake pedal. 4. From top of mounting plate, install 5/16 inch flathead screw (1) through mounting plate (7), brake pedal (A) and offset washer (2). 5. From under brake pedal, install acorn nut (3) to secure mounting plate and offset washer to brake pedal. Tighten acorn nut to 25-29 ft-lbs (33-39 Nm). 6. Obtain brake pedal cover (5) and pedal tread (6) from kit. Align and insert tread (6) into the brake pedal cover. 7. From the side, slide the brake pedal cover assembly over the mounting plate (and pedal) and align the two holes in bottom of cover with two holes in mounting plate. 8. Obtain the two 10-24 screws (4) from kit. From under brake pedal (A), install screws through holes in mounting plate (7) and into pedal cover (5). Tighten screws to 20-22 in- lbs (2.2-2.5 Nm)

Incoming search terms: