650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

Yamaha Virago 750/ 1100 InstaTrike REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 26-12-2011

download
Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand. 2) Attach Bracket A (left) to outside of rear passenger foot peg mount. Place spacers between Bracket A and foot peg mount. Use new bolts provided. 3) Attach Bracket B (right) to outside of rear passenger foot peg. Place spacers between Bracket B and foot peg mount. Use new bolts provided. Bracket will extend over top of mufflers. 4) Attach Brackets C (left) and D (right) to rear frame bolts on
motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A & B and to the TOP of the forward hitch arms. Ensure hitch is square on motorcycle and snug bolts for Brackets A, B, and E,F at this time. 6) Raise rear of hitch so bottom of Brackets C & D are flush with top of rear hitch plate. Ensuring that hitch is square with motorcycle, carefully mark hole locations for bottom of Brackets C&D on rear hitch plate. Drill rear hitch plate holes with 3/8 inch drill. This step ensures proper alignment and spacing of hitch on the motorcycle. 7) Tighten all bolts ensuring that hitch is square on motorcycle. Periodically check bolts for tightness. Bracket Identification
INSTALLATION OF THE TOW-PAC HITCH CART.
1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bo

Incoming search terms:

2008-2009 HONDA CBR 1000 RR DUAL CANISTER SLIP-ON INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-11-2011

download
INSURE THE EXHAUST SYSTEM AND EXHAUST COMPONENTS ARE FULLY COOLED. 2. INSURE THE MOTORCYCLE IS STABLE ON KICKSTAND OR REAR CENTERSTAND OR SERVICE TABLE. 3. REMOVE THE 3 PLASTIC BUTTONS HOLDING THE PLASTIC COVER OVER THE EXHAUST SERVO. (THIS IS LOCATED DIRECTLY INSIDE THE RIGHT REAR PASSENGER PEG BRACKET) DETACH THE CABLE END FROM THE SERVOnWHEEL AND REMOVE THE ENTIRE CABLE FROM THE RETAINING CLIP. THE ENTIREnCABLE WILL NOW REMOVE WITH THE REST OF THE EXHAUST.REPLACE THE PLASTIC COVER FOR THE SERVO AND REINSTALL THE 3 PLASTIC BUTTONS. 6. REMOVE THE STOCK MUFFLER MOUNTING BOLT. REMOVE 7. REMOVE THE STOCK EXHAUST CLAMP. (IT IS NOT UNCOMMON FOR THE CLAMP BOLT TO BREAK DURING REMOVAL.)b8. REMOVE THE ENTIRE STOCK EXHAUST ASSEMBLY. BE CAREFUL NOT TO SCRATCH THE SWING ARM DURING REMOVAL. 9. REMOVE THE STOCK EXHAUST GASKET FROM HEADER PIPE IF IT DID NOT COME OFF WITH THE STOCK EXHAUST. THIS GASKET WILL
NOT BE USED. 10. PREASSEMBLE THE HYPERFLO EXHAUST BEFORE INSTALLING. HYPERFLO RECOMMENDS YOU DO THIS PORTION ON CARPET OR A CLEAN PADDED AREA. YOU MAY ALSO USE THE PLASTIC BUBBLE PACKAGING AS A PAD TO PROTECT THE CANISTERS DURING PREASSEMBLY. 11. PREASSEMBLE THE LARGE DIAMETER CAN TO THE S-PIPE FIRST. INSTALL THE SPRING ON THE CANISTER FIRST AND PULL AWAY FROM THE CANISTER TO INSURE YOU DO NOT SCRATCH THE CANISTER

HARLEY DAVIDSON DYNA GLIDE ADJUSTABLE HIGHWAY PEG MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
Installation 1. See Figure 1. Install setscrew (14) into lower hole on frame tube boss (2) leaving .20 in. of setscrew (or three threads) exposed. 2. Place highway peg mounting plate (1) into position. For a lower peg position, place bottom hidden hole in mounting plate over setscrew. For a higher peg position place upper hidden hole in mounting plate over setscrew. Attach mounting plate to frame tube boss using 1 in. long screw (3), lockwasher (4), and flat washer (5) from kit. Tighten screws to 33 ft-lbs. 3. Install footrest support (6) onto highway peg support plate using hex nut (7), lockwasher (8) and flat washer (9) from kit. Tighten nut (7) to 47 ft-lbs. 4. Locate spring washer (10) from kit. While holding spring washer in position on inside of footrest support (with square edge towards motorcycle), position footpeg (not included with this mounting kit) between footrest support mounting tabs, as shown. 5. Insert 1-1/2 in. long screw (12) from kit through footrest support mounting tabs, footpeg, and spring washer. Secure using locknut (13) from kit. 6. Repeat these steps for the other side of vehicle. 1 WARNING These footrest pegs must fold upward and toward the rear at about a 45°angle when retracted. If they do not, peg could contact ground while motorcycle is in a turn, causing loss of control or startling the rider, resulting in possible personal injury. If pegs do not fold up and back at a 45°angle, remove pegs and turn them over so the flat surface is facing forward.

Incoming search terms:

2008 Harley Davidson Softail Deluxe Exhaust Installation Supplement to Installation Manua

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Install LH and RH passenger foot peg mount using 3/8×2-1/4″ hex head bolts, 3/8″ SAE flat washers, 3/8″ lock was and 1″ spacers between the motorcycl frame and mount. Figure 1 hers e xhaust ter) n’t Cut 6-1/4″ from end Cut 1/2″ from end Figure 2 2. Remove exhaust chrome covers from header pipes. 3. It is not necessary to remove the front cylinder’s front cover. Remove header pipes from cylinder heads. Cut pipes as shown in Figure 2. 4. Replace header pipes Cut cover 5-5/8″ from end – Shown already cut Figure 3 5. Cut top cover as shown in Figure 3. 6. Install supplied extension pipes as shown in Figure 3 using the OE e clamps. (Clamps covered by covers in picture – covers will be installed la Rotate clamps to make sure they don’t interfere with the foot peg mounts. Do tighten clamps yet. 7. Mount exhaust hanger bracket to body frame with (3) supplied vibration mounts. Figure 4. Figure 4 8. Install supplied clamps to ends of mufflers and fit over exhaust extensions. 9. Attach exhaust pipes to hanger bracket with OEM hardware (4 bolts). Apply Red Loctite to OEM bolts. Figure 4. 10. Install all chrome covers 11. Tighten all exhaust clamps. Figure 5 12. Install supplied chrome cover with clamp removed from cut OE chrome cover. Supplied cover slips over OE chrome cover. Push cover forward to prevent the body from hitting the cover. Figure 5. 13. Move OE clamp backwards and install 14. Position luggage rack as shown in figure 5. Install luggage rack with OE bolt in the Figure 6 Bracket OE Bolt Clamp Figure 7 Drill ¼” holes bracket using OE bolt and supplied 3/8″ bolt. Figure 6. 7 and drill two ¼” holes in shock tower mount. 1 rear and the supplied ¼” bolts in the front.

HARLEY DAVIDSON SKULL SHIFTER PEG/ HEEL REST PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
Models Shifter Peg Kit, Part Number 34689-04 is designed for installation on all model Harley-Davidson motorcycles. Heel Rest Pad Kit, Part Number 34699-04 is designed for installation on all models equipped with a Heel Rest Kit, Part Number 50227-01 or 50236-01. INSTALLATION Shifter Peg 1. Remove and discard the original equipment shifter peg. If needed, use a heat gun to apply heat to the shift lever and shifter peg threads to aid in peg removal. 2. See Figure 1. Using the screw (5), attach the peg (1) and tread (3) assembly to the shift lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). Heel Rests NOTE The chrome heel rest covers are side-specific. For best appearance, install so the HARLEY-DAVIDSON text is above the skull, and the MOTORCYCLES text below . 1. See Figure 1. Using the screws (5), attach the left-side heel rest (1) and tread (3) assembly to the left-side heel rest lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). 2. Repeat for the right-side heel rest (2) and tread assembly

SUZUKI M109 BRAKE PEDAL INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 29-01-2011

download
1. Remove the pinch bolt from the bottom of the stock brake pedal. Notice that the slot in the pedal aligns with a punch mark on the end of the shaft. Using a needle- nose pliers disconnect the return spring from the pedal. Remove the pedal by sliding it outward until it touches the foot peg mount and then pushing the shaft inward. 2. Remove the pinch bolt from the new brake pedal and install it so that the slot is aligned with the punch mark on the end of the shaft. Install the pinch bolt and tighten it securely. Reconnect the pedal return spring

HONDA VT 1100 HIGHWAY MOUNTS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the parts supplied from the package and lay them out in front of you. Remove the screws from the mounts and clamps. See photo (1), notice that the two clamp halves (1A) and the two arms (1B) are the same. Notice that the two mounts (1C) are different and are machined at opposite angles. The mounts (1C) can be installed facing forward to the front of the bike as shown in photo (1) or facing to the rear of the bike as shown in photo (2) depending on how far forward you want the pegs to be located. 2. Starting on the right side choose which way you want the mount to face. Hold one of the mounts up against the frame tube. Hold one of the arms up against the mount where it bolts together. The arm should be horizontal or level when the bike is sitting up straight. If not use the mount with the opposite angle. Next while still holding the mount in place at the desired location place one of the clamps behind the mount and start the screws. Snug the screws only leaving them loose enough to make further adjustments later. Next Bolt one of the pegs loosely to the arm as shown in photo (2). Notice that there are eight dowel pin holes on the mount and seven on the back side of the arm allowing 56 possible angles or positions for the arm to be set at. Holding the arm/peg assembly up to the mount select the desired position for the arm and place one of the dowel pins supplied into the nearest set of holes on the mount and arm. Bolt the arm/peg assembly to the mount using one of the large button head Allen screws and a washer provided. Once you have the arm close to where you want it you can make fine adjustments by removing the large Allen screw, removing the arm and moving the dowel pin to the next hole in the mount. Moving the pin clockwise one hole will rotate the arm in the opposite direction approximately ½”. Likewise moving the pin counter clockwise will rotate the arm in the opposite direction. 3. Repeat this procedure on the left side. Sit on the bike. Place your feet on the highway pegs and verify that you have them set at the most comfortable position for you and that they are set the same on both sides. Tighten all bolts and screws securely

PASSENGER FLOORBOARD RELOCATION ARMS FOR TRIUMPH AMERICA AND SPEEDMASTER

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. If you are installing the relocation arms at the same time as floorboards install the floorboards first per their instructions. When installing the relocation arms with floorboards already installed proceed as follows. 2. Starting on the left side, fold the floorboard up. Remove the socket head bolt and nut which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which holes the dowel pins are located in. 3. Install one of the 5/16″x1 Ω” hex bolts supplied thru the stock peg support from the backside (The threads of the bolt will face out towards you.) Place the two dowel pins into the holes at one o’clock and seven o’clock on the stock peg mount. Place the spacer blocks backside (stamped with an “L”) onto the bolt and align the hole with the pins. 4. Locate the relocation arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the holes in the arm that are directly across from one another (180 degrees apart). Place the arm onto the spacer bock aligning the pins in the arm with the holes closest to six and twelve o’clock. Depending on which of the two sets of holes on the arm you chose the arm would, either be down at about seven o’clock or just below nine o’clock. These are the initial height settings and you may select which ever set is most comfortable for the passenger. Install one of the acorn nuts supplied onto the bolt and make finger tight. 5. Place the floorboard with its two dowel pins into the set of holes at the other end of the relocation arm that allows the floorboard to be horizontal or parallel to the ground. Use one of the 5/16″x3/4″ socket head bolts supplied to bolt the floorboard to the relocation arm and make finger tight. 6. Install the right side in the same manner, place the dowel pins in the holes at eleven o’clock and at five o’clock on the stock peg mount, then the spacer blocks backside (stamped “R”) onto the pins followed by the relocation arm with two dowel pins in one set of holes (180 degrees apart). Check to see that the right arm is at the same height or position as the left then install the acorn nut finger tight. Bolt the floorboard the other end of the arm using the remaining dowel pins and socket head bolt. Tighten the two bolts with the acorn nuts and the two socket head bolts securely

2" PEG EXTENSIONS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 23-12-2010

download
* Remove the foot peg from the folding clevis base by loosening the allen bolt at the end of the foot peg, then remove the allen bolt from the peg. * Place the new longer allen bolt thru the peg and slide the smaller, male end of the peg extension onto the bolt. * Screw this assembly back into the clevis or folding part of the peg base. * Rotate the peg to the desired angle and tighten the allen bolt.