KAWASAKI VULCAN 900 SLASH CUT STAGGEREDS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Attach mounting bracket 440-P to frame using two stock fl ange head bolts used on stock upper bracket (Figures 1 and 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 3). 3. Lay front header, and rear header into their head heat shields and muffl er body heat shields. 4. Install #20 hose clamps (supplied) on heat shields and #36 (supplied) on muffl er body heat shields by feeding tail end of clamps into heat shield clips (fi gure 3). Take note of clamp screw head direction (Figure 4). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 5. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 6. Slide nut plates inside bracket that is welded to backside of muffl er bodies (Figure 5). While holding nut plates in place, attach muffl er bodies to mounting bracket 440-P using two 5/16″x 5/8″ fl ange head bolts (supplied). Leave them loose at this time. 7. Align muffl er bodies so they are level and parallel when viewing from the right side of the bike. Tighten cylinder port exhaust fl ange nuts on front and rear cylinders. 8. Tighten the fl ange bolts on both muffl ers. 9. Tighten all heat shield clamps. 10. Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. NOTE: For models with fl oorboards, two Spacer washers are supplied to space out the fl oorboard bracket enough to allow the fl oorboard to fold up without hitting the heat shield. 11. Be sure to tighten all hardware before starting your motorcycle. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up

HARLEY-DAVIDSON SOFTAIL CROSSOVER REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-04-2012

download
EXHAUST SYSTEM REMOVAL READ ALL INSTRUCTIONS BEFORE BEGINNING 1. Under the oil tank on the right hand side, locate the rear O² sensor connector. Unplug sensor and feed the end of wire through the frame freeing it from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Open the plastic cover above the rectifier on front of the frame to access to the front O² sensor connector. Unplug sensor from harness. Remove ZIPSTRIP holding wire to frame and feed the wire through freeing it from motorcycle. 3. On floorboard equipped models, loosen the right hand floorboard mounting bolts to gain clearance for exhaust removal and installation. 4. Loosen the heat shield clamps on both front and rear exhaust pipes. 5. Remove the mounting nuts from each head pipe, located at the cylinder head. 6. Remove the nuts attaching the exhaust mount bracket to the frame. 7. On FLSTD and FLSTF models, you will need to remove the right side passenger foot peg and hanger, as this is attached to the exhaust mount bracket. Replace the passenger foot peg assembly using the BOLT 14 Allen bolt (supplied). 8. Remove the entire exhaust system and set it aside. 9. Remove the two lower mounting studs from the frame See figure 1 . Recommended replacement exhaust port gaskets, H-D P/N: 65324-83A. 10. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. See figure 2 . NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. 11. Remove O² sensors from stock head pipe and set aside for re-installation on your new RUSH exhaust system. PAGE 1 OF 4 RUSH RACING PRODUCTS EXHAUST SYSTEM INSTALLATION P/N 7020 – 7120 BEFORE INSTALLATION PLEASE READ ALL INSTRUCTIONS 1. Remove header and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through See figure 3. 2. Apply a small amount of anti-seize compound to the threads of the O² sensors and install them into the new head pipe. NOTE: Be careful not to get anti-seize on sensor tip, it may affect sensor function. 3. Install circlips and flanges from stock system onto the new head pipe See Figure 2. Note: Replace circlips if bent or damaged 4. Attach BRKT-007 to frame using two BOLT 12 Tighten to factory specs. 5. Install complete assembly into exhaust ports (rear port first). Use stock flange nuts, Do Not Tighten .

HONDA SHADOW AERO 750 STRAIGHTSHOT HS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 03-11-2011

download
Install mounting bracket (stamped 359-P) in the original bracket mounting position, using two 10mm bolts and
one 10mm nut (supplied)(Figure 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark the outside edge of each heat shield to show location of hose clamp mounting clips (Figure 3). 3. Slide flanges onto head pipes and lay head pipes into
heat shields. Loosely install hose clamps by feeding tail end of clamp into heat shield clips (Figure 3). Take note of screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas.
4. Using stock nuts, carefully install head pipes into exhaust ports (Assistance may be required). NOTE: Do not tighten at this time.