HARLEY DAVIDSON SCREAMIN' EAGLE ELECTRONIC FUEL INJECTION (EFI) STAGE 1 KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
Installation NOTE The installation procedure is divided into three parts: 1) Replacing ECM (1996 and earlier models ONLY) 2) Calibrating the ECM 3) Replacing stock air cleaner with air cleaner from kit. 1) REPLACING ECM (1996 and earlier models ONLY) 1. Refer to the REMOVAL/REPLACEMENT section 9C in the 1995-1996 FLT Service Manual, Part No. 99483- 96A. 2. Install ECM in accordance with the installation procedure given in the Service Manual. 2) CALIBRATING THE ECM Have dealer recalibrate the ECM prior to starting vehicle. NOTE The product information (EO) label contained in this kit is required in the state of California only. This label is required to aid in passing the California Smog Check Program. Place the information label on the right side of the frame directly beneath the VIN sticker. Do not place the label over other product information labels. Do not place the label on motorcycles other than those specified in the instruction sheet. 3) REPLACING STOCK AIR CLEANER Removing Stock Air Cleaner NOTE Refer to the applicable Service Manual and check the warm- slow idle speed adjustment before removing stock backplate. 1. Remove stock backplate following the instructions given in the appropriate Service Manual. 2. See Service Parts Illustration. Retain stock air cleaner cover and buttonhead screw and washer. Installing High Performance Air Cleaner 1. See Service Parts Illustration. Locate banjo bolts (10) included with kit. Place one washer (11) over each banjo bolt. Insert bolts through holes in mounting bracket (15). Place a second washer over each bolt. Place manifold breather (16) over bolts with hose fitting toward rear of motorcycle. Install remaining washers over the ends of bolts

HARLEY DAVIDSON SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) Original Equipment (OE) Air Cleaner Removal For carbureted models: Refer to the service manual and check the warm-slow idle speed adjustment before removing the OE air cleaner backplate. For EFI (fuel-injected) models: Have a Harley-Davidson dealer recalibrate the ECM prior to air cleaner installation. 2. Remove the air cleaner backplate following the instructions in the service manual. Retain the two breather screws (A) removed from the backplate (see Figure 1). The remaining parts can be discarded. 3. See Figure 1. Remove and discard induction module bracket (B). “Heavy Breather” Air Cleaner Installation NOTE When servicing the air cleaner, apply Loctite 243 (blue) to all threaded fasteners (both male and female threads). 4. Install the new O-rings (4) in the grooves around the breather screw holes on the carburetor or induction module side of the backplate (1 or 2)

HARLEY DAVIDSON EFI SCREAMIN' EAGLE BIG BORE EFI STAGE 2 KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION Installation of this kit is divided into six steps: 1. Big-Bore Cylinder and Piston Conversion 2. High Performance Camshafts 3. High Performance Clutch Diaphragm Spring 4. High Performance Air Cleaner 5. Calibrate the ECM 6. Exhaust NOTES This Big-Bore Stage 2 kit is intended for High Performance applications only. This engine-related performance part is legal for sale or use in California on pollution-controlled motor vehicles. Engine-related performance parts are intended for the experienced rider only. -J04173 1 of 5 The air cleaner contained in these kits is designed to perform with these kits only. Any other combination of components is not confirmed to be legal for street use. The Product Information Label contained in this kit is required in the state of California only. This label is required to aid in passing the California Smog Check Program. Place the Product Information Label on the right side of the frame, directly beneath the VIN sticker. Do not place the label on motorcycles other than those specified in the Instruction Sheet. Gaskets provided in the 1690 conversion kit eliminate the need for original head gasket O-rings. For this reason, DO NOT install the Original Equipment (OE) O-rings (Part Number 11273) to the top of cylinder dowels, or severe engine damage may occur. Big-Bore Cylinder and Piston Conversion NOTE Installation of this kit requires removal of the cylinder heads, cylinders and pistons. Refer to Section 3, ENGINE: STRIPPING MOTORCYCLE FOR SERVICE and TOP END OVERHAUL of the applicable Service Manual for instructions. High Performance Camshafts NOTE Installation of this kit requires removal and re-installation of the cam support plate. Refer to Section 3, ENGINE: BOTTOM END Cam Support Plate, Removal and Disassembly/Assembly (Camshaft, Camshaft Bearings) of the applicable Service Manual for instructions. Measuring Piston-to-Valve Clearance After installing non-stock cams, check piston-to-valve clear- ance. 1. Apply 1/8-inch (3 mm) layer of clay to crowns of pistons in areas where valves meet pistons. 2. Refer to the appropriate Service Manual and assemble the heads and valve train, and tighten cylinder studs to torque specified. 3. Turn engine through two complete revolutions by hand. 4. Remove heads and measure clay at its thinnest point. NOTE Clay must measure 0.080 inch (2.03 mm) at its thinnest point. If this measurement does not meet minimum thickness, depth of valve notches must be increased. The depth of the notches must not exceed 0.135 inch (3.43 mm). Measuring Valve-to-Valve Clearance NOTE Wait ten minutes before turning the engine after installing push rods. This allows tappets to bleed down and prevents you from bending push rods or valves. 1. Rotate the engine so that both valves of the front cylinder are partially open. Shine a light through the exhaust port and look through the spark plug hole to view the valves. Turn engine, if required, to the point where the exhaust evel sensor to the fuel pump with screw (3). Tighten the screw enough to seat the fuel sensor against the mounting tab e. Route fuel level sensor wiring under the fuel hose and connect the fuel level sensor to the low fuel switch connector on the fuel pump module. If necessary use the jumper harness (Figure 4, item 5). f. See Figure 2. Secure the fuel pump wires and con- nectors

Incoming search terms: