Yamaha TW200N/ TW200NC SPECIFICATIONS AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EAS00017 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head pipe. EAS00018 MODEL CODE The model code label 1 is affixed to the frame. This information will be needed to order spare parts CABLE ROUTING 1 Throttle cable 2 Front brake light switch lead 3 Right handlebar switch lead 4 Clutch cable 5 Left handlebar switch lead 6 Clutch switch lead 7 Front turn signal/position light lead (left) 8 Main switch lead 9 Indicator lights lead 0  Speedometer cable A Meter light lead B Headlight coupler C Wire harness D Front turn signal/position light lead (right) E Brake hose ب Fasten the brake hose with a plastic locking tie to the brake hose grommet. ة Fasten the wire harness with a plastic locking tie PERIODIC CHECKS AND ADJUSTMENTS INTRODUCTION This chapter includes all information necessary to perform recommended checks and abjustments.If followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work.This information applies to vehicles already in service as well as to new vehicles that are being prepared for sale.All service technicians should be familiar with this entire chapter. PERIODIC MAINTENANCE CHART FOR EMISSION CONTROL SYSTEM

SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

SUZUKI SV650/ S PERIODIC MAINTENANCE CHART

0

Filed Under (Suzuki) by admin on 26-02-2011

download
Item km miles months 1000 6000 12000 18000 24000 600 4000 7500 11000 15000 1 6 12 18 24 Air cleaner Spark plugs Tappet clearance Engine oil Engine oil filter Fuel hose Engine idle speed Carburettor synchronization Evaporative emission control system PAIR air supply system Throttle cable play Clutch cable play Radiator hoses Engine coolant Drive chain Brakes Brake hoses Brake fluid Tires Steering Front forks Rear suspension Exhaust pipe bolt & nut Chassis bolt & nuts – - – R R – I I I – - I I – - – I – - T T Replace every 4 years Replace vapor hose every 4 years – - I – I I I – - Replace every 2 years Clean & lubricate every 600 miles (1000km) Replace every 4 years Replace every 2 years R R R R – - R – I I R I I R I R – Inspect and adjust, clean

HARLEY-DAVIDSON Sportster Solid Axle Suspension Owner's Maintenance Notes

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 24-26psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential, and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” approximately ¾”-1″ with a new belt or 1″ to 1-1/2″ with a used belt of total vertical movement. Do not use commercial belt dressing compounds on the belt except for Harley Davidson Poly-Oil, PN 99860- 81. These compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension is a “Zero Flex” solid axle with high performance adjustable pre-load coilover shocks. The suspension system is designed to give you the best ride with a load of no more than 400 pounds. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals

KTM WP FORK 4860 MXMA CLOSED CARTRIDGE REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 22-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork

Incoming search terms:

2005-2007 KTM 5018 DCC 5018 SXS 5018 SMR WP SHOCK ABSORBER REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
liter fuel consumption is equivalent to approx. 15 operating hours Check the bearing in the shock absorber top / replace if necessary Check the piston rod on scratches / leakage Check the static sag – before riding Check the spring Check the bump rubber Check the O-ring of the spring retainer / replace if necessary Complete maintenance of the shock absorber 10 hours 65 liter 20 hours 130 liter 30 hours 200 liter 40 hours 260 liter 50 hours 325 liter 60 hours 400 liter 70 hours 455 liter 80 hours 520 liter 90 hours 600 liter 100 hours 665 liter Adjusting the position of the compression and rebound damping Rebound damping: -Turn in the adjusting screw 1 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, low speed: -Turn in the adjusting screw 2 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, high speed: -Turn in the adjusting screw 3 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Adjusting the spring preload NOTE: the spring preload is the difference between the unloaded and preloaded length of the spring. -Tighten the adjusting nut 4 with the special tool T106 until you have the prescribed spring preload. -Tighten the lock screw on the adjusting nut. Recommended periodic maintenance and inspection of the 5018 SXS/SMR Shock absorber

Incoming search terms:

YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Incoming search terms:

Rokon Illustrated Repair Procedures and Parts Manual

0

Filed Under (Rokon) by admin on 20-11-2010

download
Front and Rear Brake. Check brake action. Check pucks to see that they are not over worn. There should be visible brake material on both sides of the brake disc. See Section 6. Fuel Tank. Check fuel level. Fill as necessary. Use super unleaded for altitudes above 10,000 ft. Engine Oil. The engine holds .6 qt. of SAE10W30/40 motor oil. Fill to the dipstick “full” line. Miter Box and Transmission. They are filled at the factory and need not be checked at the start. The miter box should have 2.5 oz. of EP 80W90 gear lube oil. The transmission takes 6 oz. of EP 80W90 gear lube oil. The transmission has a fill to plug near the bottom of the transmission( shown on page 46). There is no fill level for the miter box. Over filling of either the miter box or transmission will result in leakage. Throttle. Check for proper throttle cable operation. Look for smooth response to twist action. Wheels and Tires. Check Tire pressure, wear and damage. Fittings and Fasteners. Check all fittings and fasteners. Drive Chains. Check chains for tension and lubrication. Adjust tension for 1/2″ – 3/4″ deflection at mid point. Engine Manual. Read your engine manual completely and follow all instructions Periodic Maintenance and Adjustment 1. Inspect all fasteners for tightness. 2. The drive chains require adjustment at intervals, depending on the mileage and the care which the operator has given the chains. Initial wear must be taken up by adjustment after the first few hours of use. Total deflection should be 1/2″ to 3/4″ when measured midway between the two sprockets of the most loose position. To adjust the chains, loosen the axle bolts and the adjusting bolt lock nuts, and turn the adjusting bolts equally in or out as required to give the chain the proper setting. After adjusting the chain, rotate the wheel and check to make sure the chain is aligned properly. Periodically, the chains should be removed from the machine and cleaned in solvent and re-lubricated. They should be lubricated with one of the chain lubricants on the market which can be applied to the chain in a liquid form and will penetrate to the inner parts of the rollers. 3. Clean the air filter based on use. See Engine Manual. 4. Use normal repair procedures for tires and tubes. Re-seat the tire beads with 40 PSI , then deflate to the 3 -5 PSI operating pressure.

Incoming search terms: