Yamaha FJR Backrest REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Motorcycling is a dangerous activity that can result in serious injury or death. Please be advised that this product has NOT been tested under every conceivable condition. While every effort has been made to design a sturdy and reliable product, numerous unpredictable conditions and/or variables could occur during its use, resulting in possible property damage, personal injury or death. By proceeding with the installation, the purchaser acknowledges that these inherent dangers and unpredictable conditions exist. Furthermore, the purchaser understands that Sargent Seat Cover Co. / D.B.A. Sargent Cycle Products N.A. shall not be held liable for any direct, indirect, incidental, special, or consequential damages arising out of or in connection with the use of this product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. If the purchaser does not agree to all terms of this limitation of liability/disclaimer, the product may return to Sargent Cycle Products N.A. in its original packaging (within 30 days) for a full refund of the purchase price (excluding shipping and handling).

HARLEY DAVIDSON DYNA GLIDE ADJUSTABLE HIGHWAY PEG MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
Installation 1. See Figure 1. Install setscrew (14) into lower hole on frame tube boss (2) leaving .20 in. of setscrew (or three threads) exposed. 2. Place highway peg mounting plate (1) into position. For a lower peg position, place bottom hidden hole in mounting plate over setscrew. For a higher peg position place upper hidden hole in mounting plate over setscrew. Attach mounting plate to frame tube boss using 1 in. long screw (3), lockwasher (4), and flat washer (5) from kit. Tighten screws to 33 ft-lbs. 3. Install footrest support (6) onto highway peg support plate using hex nut (7), lockwasher (8) and flat washer (9) from kit. Tighten nut (7) to 47 ft-lbs. 4. Locate spring washer (10) from kit. While holding spring washer in position on inside of footrest support (with square edge towards motorcycle), position footpeg (not included with this mounting kit) between footrest support mounting tabs, as shown. 5. Insert 1-1/2 in. long screw (12) from kit through footrest support mounting tabs, footpeg, and spring washer. Secure using locknut (13) from kit. 6. Repeat these steps for the other side of vehicle. 1 WARNING These footrest pegs must fold upward and toward the rear at about a 45°angle when retracted. If they do not, peg could contact ground while motorcycle is in a turn, causing loss of control or startling the rider, resulting in possible personal injury. If pegs do not fold up and back at a 45°angle, remove pegs and turn them over so the flat surface is facing forward.

DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY DAVIDSON SUPPLEMENT ARY 12 VOLT POWER SOURCE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
Installation NOTE This power source can be mounted on either side cover of the motorcycle, except on models with cruise control, which must have the power source mounted on the right side cover. 1. Remove seat and the side cover chosen for installation (see note above). 1 WARNING To avoid accidental start-up of motorcycle, and possible personal injury, disconnect the battery cables (negative cable first) before performing any of the following procedures. If the positive cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion resulting in personal injury. 2. Disconnect battery, negative cable first. 3. See Figure 1. A 7/8 inch diameter hole needs to be drilled in the top of the side cover to mount the power source. It is important that the hole is properly located as follows, before cutting : a. Cut out template on page 3. Line the template up on the outside top of the cover using the top and rear cover edges as guides as shown in the illustration. Tape the template in place. b. After the template is in place, locate the appropriate hole on the template that matches the applicable year and side cover. Check to be sure that the entire hole area is on the flat top surface of the cover. No part of the hole should extend onto the sharply curved edge of the cover. 4. Carefully drill a 7/8 inch diameter hole at the location marked on the template. Drill from the outside of the cover to the inside. 5. See Figure 2. Unscrew outer sleeve of socket assembly (1) from socket body. Place the socket body into the cover hole and secure the socket in place by screwing

HARLEY DAVIDSON COIN HOLDER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
Installation 1. See Figure 1. Attach coin holder bracket and rubber strip to handlebar, as shown, with hardware from kit. NOTE Be sure coin holder does not restrict full movement of handlebars. note NOTE For use on 7/8 in. diameter handlebars the rubber strip will have to be cut to 3 in. long. 1 WARNING Install coin holder bracket so longer bracket half extends toward the front of the vehicle. Bracket extended toward the rear could cause personal injury should the vehicle operator come in contact with the bracket during unexpected quick stops or in case of an accident. 2. Push coin holder onto bracket extension until sprung bearing locks holder in place on bracket

HARLEY DAVIDSON SCREAMIN' EAGLE XL1200S RACE IGNITION SYSTEM Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 26-12-2010

download
Disconnect battery, negative cable first. 2. See Figure 1. Remove seat and locate ignition module. 3. Remove the two nuts that hold the ignition module in place. 4. Unplug the two module connectors and remove module. 5. Plug in new module and secure module in place with nuts removed in step 3. Tighten nuts to 15-21 in-lbs (1.7-2.4 Nm). 6. Disconnect spark plug cables from coil towers, noting their positions for reinstallation on new coil. ® Kit Numbers 32737-98, 32738-98, 32739-98 Figure 1. Ignition Module i01020 1 of 2 NOTE The spark plug cables have numbers printed on them that correspond to numbers adjacent to the coil towers on the coil. 7. See Figure 2. Making note of wiring positions, disconnect primary wire plug from back of coil by gently prying up latch and pulling connector rearward. 8. Remove mounting bolt and remove existing ignition coil. 9. Install new coil with mounting bolt removed in previous step. Tighten bolt to 2-6 ft-lbs (3-8 Nm). 10. Plug in primary wire connector into back of coil. 11. Connect spark plug cables to new ignition coil. 1 WARNING Always connect the positive battery cable first. If the positive cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion resulting in personal injury. 12. Reconnect battery cables, positive cable first. 13. Check engine timing according to procedures in applicable XLH Service Manual.

BMW R1200GS Exhaust System Installation instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
The manufacturer, importer or dealer shall not be liable for any incidental damage including personal injury or any other damages caused by improper installation or operation of the Akrapovič exhaust system. When installing the Akrapovič exhaust system be careful that the exhaust system does not touch other parts sensitive to high temperature. 2. Akrapovič makes no representation or warranties with regard to damage caused by the improper installation, use and maintenance of the Akrapovič exhaust system. The warranty is limited to defects recognized by our technical department and due to normal use, and excludes items subject to normal wear (gaskets and damping wool). The guarantee is void in case of accident, modification, improper or competition use. 3. Do not attempt to install the Akrapovič exhaust system on a vehicle model for which it was not made or tested by Akrapovič. 4. When the exhaust system gets very hot during operation, be careful not to burn yourself on the exhaust system or parts which are in direct contact with it, even when the engine is not running. Also protect other people, especially children, from the injuries mentioned above. 5. In some cases Akrapovič exhaust system kits contain chemical products (ceramic anti-seizing grease; bolt sealant). Handle with care, do not inhale or swallow. Avoid excessive contact with skin, eyes or mucous membranes. Keep out of reach of children. 6. Technical specifications of Akrapovič exhaust systems and related products are subject to change without notice. 7. Before removing the original exhaust system from your vehicle, please compare the parts you received with the list of materials provided in the installation manual in order to assure that you have all the parts necessary for the installation of your new Akrapovič exhaust system. 8. Although this manual consists of instructions for installation in written form, as well as photographs and pictures representing individual steps of the installation, please note that the photographs and pictures are symbolic and are intended for representation of general overview only. The photographs and pictures contained herein should serve as a guideline only and actual installation of the exhaust system may not correspond with the photographs and pictures entirely.

Ducati Hypermotard Large Fuel Tank Installation Instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
REMOVING THE OEM FUEL TANK GO FOR A RIDE The best way to remove fuel from your original fuel tank is to RIDE your bike. You should already be familiar with how low you can go and the less fuel that’s in your tank before you start means the less mess you make when draining it. HM69 Fuel Tank Installation Instructions This manual is provided for marketing and informational purposes only and is a guide to assist experienced motorcycle technicians with the installation of the HM69 fuel tank. This installation involves gasoline. Improper installation, adjustment, alteration, service or maintenance regarding the HM69 fuel tank can cause property damage, personal injury or death. At-home Do-It-Yourself mechanics should not install the HM69 fuel tank if you are uncertain of your ability to properly install it and refer the installation to an authorized Ducati service department. ! REMOVE THE SEAT Remove the seat bolt at the rear of the seat with a 4mm hex key. To remove the seat, grasp both sides of the seat, lift the rear of the seat slightly, and pull the seat to the rear of the bike. The front of the seat engages onto bolts on either side of the fuel tank and can be stubborn. THIS KIT ALSO CONTAINS: © 2009 California Cycleworks, Inc. Questions? Email orders@ca-cycleworks.com 1
REMOVE THE BODYWORK The tank cover is fi rst. Remove the fuel fi ller cap and then the 4 screws you see: 2 near the front of the cover and the two aside the fi ller neck. Lift up on the forward portion of the cover and move the entire cover rearward so that the back of the cover is away from the retaining contour on the fuel tank. SIDE PANELS Remove the right side panel’s inner cover using a large coin. Both left and right side covers are retained by 3 screws with 4mm hex heads. Remove the 2 screws on the side of the tank (which were revealed with the removal of the seat). While holding the side covers to support them, remove the bottom screw. The left side cover pulls away naturally – take care not to drop the cover as the tool kit is housed inside of it, adding unexpected weight