CYCLE SOUNDS T-TAP POWER HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-04-2012

download
This t-tap plug is designed to work with Cycle Sounds audio systems. However it can be used to wire many add on 12 volt accessories to you Harley Davidson motorcycle. This plug is rated for 6-8 amps of power and should not be used for adding any product that is rated for more than the t-tap plug is rated for. Take the time to check the products power rating for which you want to install to make sure it is compatible with the t-taps amperage rating. Failure to do so couldlead to electrical failures, which could result in serious injuries or even death. it is possible to overload your motorcycles charging system by adding too many electrical accessories. U se amp meter to verify all power connections. Also check product power ratings for anything you are trying to install. Exceeding the maximum amperage can lead to electrical failures, which could result in serious injuries or even death. INSTRUCTIONS: Step 1: remove seat on bike and locate the wire harness under the seat that matches the plugs on the t-tap harness (2120-0026.) Location may vary between bike models. Step 2: unplug bike harness and snap each end of t-tap harness in correct plug opening. When finished connect power wires to the male plug.(all Cycle Sounds audio systems come pre wired with correct wire colors and terminals). When using this t-tap for any other 12 volt accessory, make sure the red and black wires are snapped into their proper pin connectors. Kit does not come with power terminals for the accessories device. See your local bike dealer for purchase of terminals

YAMAHA ROADLINER / STRATOLINER Fuel Injected INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 28-10-2010

download
1. Be sure the main switch is in the off position during the installation process. Failure to do this will cause the “check engine” light to be set. 2. Remove seat exposing the Electronic Control Unit (ECU) and battery. 3. Remove the right side coil cover by removing two allen screws and gently pulling. 4. Disconnect the 6 pin factory connector behind the ignition coils. (Fig 1) 5. Connect Fuelpak 6 pin connectors in-line with factory connectors. 6. Disconnect 3 pin factory connectors behind the ignition coils and connect Fuelpak 3 pin connectors in-line with factory connectors. 7. Route Fuelpak harness up to battery area and reinstall coil side cover. 8. Connect Fuelpak black wire to negative ground wire. (Fig 2) 9. Locate factory 2 pin connector with brown and black wires. Disconnect empty connector and attach Fuelpak red wire connector. 10. Connect Fuelpak 10 pin connector to Fuelpak harness. 11. You are now ready to set-up your Fuelpak. INSTALLATION INSTRUCTIONS FOR P/N 65001 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION MANAGEMENT SYSTEM ROADLINER / STRATOLINER NOTICE: Fuelpak is intended for racing or off-highway use only, and is not legal for sale or use in California on pollution-controlled vehicles. PLEASE NOTE: FUELPAK USE REQUIRES A HIGH PERFORMANCE AIR FILTER. HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified.

Incoming search terms: