HARLEY DAVIDSON 360 DEGREE HIGHWAY FOOTPEG MOUNTING KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Position footpegs so rider can operate foot controls without interference. Failure to have full access to foot controls can cause loss of control, which could result in death or serious injury. (00313a) Mount the footpegs so they will not strike the ground during cornering. Foopegs striking the ground during cornering can cause loss of control, resulting in death or serious injury. (00458b) NOTE See Figure 2 for steps 2 through 6. 1. Determine what height on the engine guard you prefer for the final mounting of the footpeg mounts. Mark location, if desired. 2. See Figure 2. Obtain clamp assembly (1) from kit. Wrap the clamp halves around the engine guard and install with hinge pin head facing upward. Place the flatwasher between the ears of the clamp halves. Hold parts in posi- tion. 3. Obtain the lockwasher (13), screw (7) and one of the footpeg extensions (14) (long or short depending on kit number) from kit. 4. Position the clamp adapter (10) over the clamp assembly (1) with the “cogged” face of the adapter facing the extension arm (14). Hold clamp adapter in place. 5. Install screw (7) with internal tooth lockwasher (13) through the clamps, the clamp adapter (10) and into the extension arm (14). Position extension arm as desired. Do not tighten completely at this time. 6. Obtain the clevis/extension assembly (6) from kit. Position assembly such that footpeg pivots upward and toward the rear of the bike. NOTE: It may be necessary to loosen the screw slightly and rotate the extension to obtain this position. Tighten item 9 securely. 7 5 1 3 4 2 6 8 is02511 1. Clamp assembly 2. Arm extension 3. Clevis 4. D-washer 5. Footpeg 6. Screw 7. Clamp adapter 8. Clamp halves Figure 1. 360 Degree Footpeg Mounting Installed (Shown with Footpeg Installed) NOTE The footpeg will be a tight fit if the D-spring washer is installed correctly. 7. Refer to Figure 1. Obtain the footpeg (5), sold separately, D-spring washer (4) and screw (6) from kit. Install the D- spring washer so it is positioned inside the clevis (3) with the square “D” edge towards the inside of the mount. Hold the washer in place and slide the footpeg into position. Install the screw (6) and tighten to 19 ft-lbs (26 Nm). 8. Repeat Steps 1 through 7 for the opposite side. Position the footpeg assemblies so they are at equal heights and symmetrical. Securely tighten each assembly until it cannot be rotated on the guard with reasonable foot pressure, but do not exceed 55 ft-lbs (81 Nm) on item 7

HARLEY DAVIDSON SPORT WIND DEFLECTOR AND WINDSHIELD KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
HEADLAMP VISOR INSTALLATION (2004 ONLY) 1 2 is 01467 1. Headlamp 2. Headlamp bracket mounting screws Figure 1. Remove Headlamp Mounting Screws (Left Side Shown) 1. See Figure 1. While holding the headlamp (1), remove the left and right headlamp bracket mounting screws (2). 2. See Figure 5. Obtain the headlamp visor (2) from the kit. 3. See Figure 2. Orient the headlamp visor (1) between the headlamp and headlamp mounting bracket (2) and reinstall the headlamp bracket mounting screws (3) securing the visor and headlamp to the headlamp mounting bracket. 4. Refer to the Service Manual and adjust the headlamp for the correct angle. 2 1 3 is01468 1. Headlamp visor 2. Headlamp mounting bracket 3. Headlamp mounting bracket screw Figure 2. Install Visor Between Headlamp and Mounting Bracket (Left Side Shown) 1 2 3 is03212 1. “RT” or “LFT” marking 2. Hinge-pin head faces up 3. Clamp post socket faces outward Figure 3. Fork Tube Clamp and Post Identification (Right-Side Clamp Shown) WINDSHIELD INSTALLATION 1. See Figure 5. Obtain one of the lower mount kits from the windshield kit carton. Identify the fork tube clamp for right- side (RT) or left-side (LFT) installation as indicated in Figure 3. NOTE The lower grommets (4) have been pre-installed into the Lexan® windshield. 2. Insert the rounded end of the post into the socket in the fork-tube clamp, oriented as shown in Figure 5. Lining up the hole in the end of the post with the hole in the clamp. With a 3 mm hex key, fasten the post to the clamp with the flat-head screw (16) from the kit, and tighten to 6.8 Nm (60 in-lbs ). 3. Place the clamp around the correct-side fork tube with the hinge-pin head facing up. Insert the two longer screws (15) from the lower mount kit through the counterbored holes in the outboard side of the clamp, and thread the screws part-way into the tapped holes in the inboard half. 4. Position the clamp so the top surface is approximately 6 to 13 mm (1/4 to 1/2 inch) below the upper triple-tree, and the hinge pin is straight forward. With a 4 mm hex key, tighten the screws just enough to hold the clamp in posi- tion. 5. Obtain the remaining lower mount kit and repeat Steps 2 through 4 to install the clamp to the opposite fork tube. 6. Obtain the upper mount kit from the windshield kit carton. NOTE The upper grommets (4), socket assemblies (3), windshield mount caps (6) and 5 mm screws (9) have been pre-installed into the windshield. 7. Place one of the handlebar clamps (5) onto one side of the handlebar, in the straight section between the riser and the handlebar controls, oriented as shown in Figure 4. NOTE Temporarily disengage the switch harness retainer from the handlebar to allow installation of the clamp.