2003 – 2006 KTM The e-Axle Installation Manuals

0

Filed Under (KTM) by admin on 01-02-2012

download
Remove the stock wheel spacers from both sides of the wheel hub and install both of the Rekluse wheel spacers. After installing the Rekluse wheel spacers, stow the wheel in a suitable place so that the brake rotor cannot be damaged. See following picture. 5 5. Remove the brake pads by removing the clips and sliding out the pin. See following picture. 6. Remove the leaf spring from the caliper. See following picture. 7. Re-install the brake pads with the included coil spring positioned on the pin between the brake pads. Secure the pin by re-installing the 2 clips. See following picture. Coil Spring on the pin and in between the brake pads 6 8. Coat the center axle in a thin layer of grease to aid in sliding the center axle on and off. Note: Coat the center axle in a thin layer every time it is reinstalled after removing the front wheel for tire maintenance. 9. Position the front wheel back in between the forks so that the brake disk is in place between the brake pads, and so the wheel spacers line up with the hole in the fork fists. 10. Slide the center axle, with 30-mm Bushing attached, through the right-side fork fist and through the wheel spacers in the front hub. Rotate the 30-mm bushing so the set screw is facing up, this will line the “0″ Offset Mark with the fork fist pinch clamp slot. Continue sliding the axle through until the 30-mm bushing is almost flush with the outer edge of the right fork fist. See following picture

KAWASAKI VULCAN 1500 PRO PIPE HS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece header flange and set it aside. 5. Remove the front head pipe by rotating it down and pull it out of the resonance chamber. 6. Remove the two acorn nuts and flange from the rear head pipe. Remove the two bolts from either side of the resonance chamber and lower rear pipe and resonance chamber down and out and set it aside. 7. Remove the rubber grommets at the resonance chamber mounting points. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the new mounting bracket (stamped 317) to the inside of the stock muffler mounting point (Refer to FIG. 1). 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of all three heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear and collector heat shields. To facilitate the installation of the collector heat shield use a forward sliding motion from the rear of the collector. Do not force the collector heat shield directly onto the collector as damage to the heat shield will result. Note: the collector heat shield uses the 3/8″ wide clamps. 3. Rotate the hose clamps in the shields so that the screw drives are accessible. Tighten only finger tight at this time. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Check to be sure that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 5. Install the header with the heat shields attached, to the front and rear cylinders using the stock nuts and bolts. Leave them loose at this time. 6. Slide the chrome muffler clamp (supplied) onto the inlet end of the megaphone. Install the 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by the 5/16″ lock nut (hardware supplied). Leave the clamp loose at this time. 7. Slip the megaphone onto the head pipe collector, engaging the collector heat shield between the clamp and the outer slip joint tube. Slide one dog bone shaped nut plate under the bracket that

Incoming search terms:

HARLEY DAVIDSON TOURING MODEL DRESSER DUALS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-12-2010

download
1. Remove both left and right saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffl er. 3. Remove the two 5/16″ bolts that mount the muffl er to the saddlebag supports. Repeat this step on the opposite muffl er (save these parts, they will be re-used). 4. Remove the stock muffl ers with sliding hangers and set them aside. NOTE: It may be necessary to use a penetrating lubricant to loosen the muffl er from the head pipe. 5. Find and unplug the O2 sensor wires from the wiring harness and remove cable tie holding front wire to frame. F eed the end of the wires through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing for re-installation. 6. Remove the right hand fl oor board. 7. Remove both passenger fl oor boards. 8. Loosen the heat shield clamps on both front and rear exhaust pipes. 9. Loosen the rear head pipe clamp located behind the rear cylinder. Remove the section of head pipe connecting the left side muffl er. 10. Remove the nut and carriage bolt holding the front head pipe to the bracket on the transmission housing (save these parts, they will be re- used). 11. Remove the two mounting nuts from each head pipe, located at the cylinder head. Carefully remove the head pipes and set them aside. 12. Using a 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 13. Remove the rear cylinder bracket by removing the two starter mounting bolts. Install new bracket (stamped 422-P)(supplied) and torque to 13-16 ft. lbs. (Figure 1). NOTE: Twist breather hose down towards the left hand side to get it as far away from the pipe as possible. 14. Install mounting post (from stock system) so the nut is accessible from right side of motorcycle and saddle will support underside of exhaust pipe. 15. Replace the bracket on the transmission housing with new bracket (stamped 423-P)(supplied) and torque to 13-16 ft. lbs. (Figure 2). 16. Carefully remove the exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted, replace them.

Suzuki INTRUDER 1400 SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Suzuki) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosenthe mounting bolt and pinch clamp on both left and right hand mufflers. 2. Loosenthe clamp on the crossover tube, located between the two mufflers. 3. Remove the two nuts that mount the front head pipe flange to the cylinder head. 4. Remove the two nuts that mount the rear head pipe flange to the cylinder head. 5. Remove the head pipes using a twisting motion to break the seal at the muffler and to clear the cylinder head. Note : If the exhaust coupler gaskets did not remain in the mufflers, remove them from the head pipes at this time. These coupler gaskets will not be reused in your new exhaust system. 6. Remove the mounting bolt from the left hand muffler. Remove the muffler, again using a twisting motion to seperate the crossover tube and set the muffler aside. (Save the stock mounting hardware for reuse). 7. Repeat step #6 on the the right hand muffler. Set the muffler aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Reinstall the stock head pipes to the engine. Note : Leave the flange nuts loose at this time. 3. Remove the mufflers from their boxes. There are a left and right hand muffler in this system. To define the difference between the left and right mufflers, check the bracket that is welded to the back side of the muffler. Each muffler is stamped with it’s own part number. Part # D500 is the RIGHT muffler and Part # D550 is the LEFTmuffler. 4. Install a three hole mounting bracket to each of the mufflers. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16 flange head bolts (supplied), leave them loose at this time. Note : Each muffler bracket has a number stamped on it, #179 bracket is for the left hand muffler and #180 is for the right hand muffler. When the brackets are mounted correctly, the end of the bracket with the single hole should point to the inlet end (small end) of the muffler. Refer to figure 1.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SPRINGER Dual Slip-On Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK MUFFLERS 1. Loosen the bolt on the pinch clamp at the front end of each muffler. 2. Remove the two bolts that mount the muffler to the mounting bar. Repeat this step on the opposite muffler. 3. Remove the stock mufflers and set them aside. Note: It may be necessary to use a penetrating lubricant to loosen the mufflers from the head pipes. INSTALLING YOUR NEW VANCE & HINES SLIP-ON EXHAUST SYSTEM 1. Remove the two 5/16″ flanged head bolts from the bracket that is welded to the backside of each muffler. Attach one of the mounting brackets (supplied) to each muffler, using two of the 5/16″ flanged head bolts (removed earlier), leaving them loose at this time. When the bracket is mounted correctly on the muffler, the single hole end should point down when the muffler is mounted to the bike. 2. Be sure there is a muffler clamp (supplied) over the front (notched end) of each muffler. 3. Slip the muffler onto the stock head pipe, mount the muffler to the rear most hole of the stock mounting bar, using one of the stock bolts and tighten. Repeat this step on the opposite muffler. Note: When installed correctly, the Vance & Hines logo on the muffler should face outwards. 4. Tighten the two muffler clamps. 5. Tighten the two 5/16″ flange bolts on each muffler bracket. 6. Wipe any finger prints or oil off any chrome parts of the exhaust system before starting the motorcycle. 7. Be sure to tighten all hardware before starting your motorcycle. RE-JETTING INSTRUCTIONS Re-jetting the carburetor will result in realizing the “full” potential of this performance exhaust system. Vance & Hines offers jet kits for most applications

HARLEY DAVIDSON TOURING MODEL BASIC SLIP ON'S INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
1. Remove both saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffl er. 3. Working with one muffl er at a time, support the muffl er (assistance may be required) while removing the 5/16″ bolts from the saddlebag support and slide muffl er off of the head pipe. 4. Repeat the process for the opposite muffl er. NOTE: It may be necessary to use a penetrating lubricant to loosen the muffl er from the head pipe 1. Install the band clamps (supplied) over the front of each muffl er so that the bolt is to the inside and the nut is facing down (Figure 1). NOTE: New band clamps are supplied, do not use the old clamps. 2. Install muffl er by sliding it on to the head pipe and bolting it to the saddlebag support using the stock 5/16″ bolts. 3. Repeat installation procedure for opposite muffl er. 4. Align muffl ers and tighten hardware, beginning with the 5/16″ bolts on the mounting brackets followed by the Torca band clamp. Torque spec. is 40-45 Ft./Lbs. 5. Replace the saddlebags. 6. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up. 7. Be sure to tighten all hardware before starting your motorcycle

Harley Davidson Touring/ Dresser Slip-on Exhaust System REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove both left and right saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffler. Note: On the older model Dresser, spread the clamps just enough to remove them. 3. Remove the two 5/16″ bolts that mount the muffler to the saddlebag supports. Repeat this step on the opposite muffler. 4. Remove the stock mufflers and set them aside. Note: It may be necessary to use a penetrating lubricant to loosen the muffler from the head pipe. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install one muffler clamp (supplied) over the front (notched end) of each muffler. 2. Slip the muffler over the stock head pipe, mount the muffler to the saddlebag support using the two stock 5/16″ bolts and tighten. Note : There is a different muffler for the left and right side of the motorcycle. The dent in each canister should always be facing in. This is to allow clearance for the swingarm. 3. Tighten the two muffler clamps. (Torque Specification 12 ft/lbs.) 4. Replace the saddlebags. 5. Be sure to tighten all hardware before starting your motorcycle. RE-JETTING INSTRUCTIONS Re-jetting the carburetor will result in realizing the “full” potential of this performance exhaust system. Vance & Hines offers jet kits for most applications. For fuel injected models, we recommend the use of Vance & Hines Fuelpak part number 61003. PLEASE NOTE: Every effort is made for Vance & Hines Exhaust Systems to provide improved cornering clearance. However, due to design and space limitations on some motorcycle models, ground and cornering clearance may not be improved and in some cases may be reduced. Be sure to follow proper installation instructions

YAMAHA V-STAR 650 EXHAUST SYSTEM REMOVAL AND INSTALLATION

0

Filed Under (Yamaha) by admin on 18-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the right hand frame cover to avoid scratching it. 2. Remove the nuts that mount the rear header to the cylinder head. 3. Loosen the pinch clamp on the inlet end of the lower muffler. 4. Remove the two bolts that mount the mufflers to the muffler bracket, located between the two mufflers. Save the hardware for reuse. 5. Pull the rear head pipe out of the exhaust port. Slide the muffler assembly with the rear head pipe attached, rearward, disconnecting it from the front head pipe. Set the assembly aside. Note: Keep the front head pipe attached to the motorcycle, it will integrated with the new exhaust system. 6. Remove the muffler mounting bracket from the frame and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the V&H muffler mounting bracket (stamped 272) to the frame using the stock hardware and mounting location. Refer to figure 1 2. Slip the T-bolt band clamp (supplied) over the straight pipe that is welded to the front muffler. 3. Slip the front muffler assembly over the stock head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using two of the 5/16″ flange head bolts (supplied), but leave them loose at this time. Refer to figure 1. 4. Install the rear header assembly to the exhaust port using the stock 8mm nuts, but leave them loose at this time. 5. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the rear muffler. Attach the muffler to the mounting bracket using two of the 5/16″ flange head bolts (supplied), but leave them loose at this time. Refer to figure 1. 6. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 7. Align the mufflers so they are parallel when viewing from the right side of the bike, and tighten the 5/16″ flange bolts on the back side of both mufflers. 8. Tighten the two header flange nuts on the rear head pipe. 9. Tighten the T-bolt clamp at the slip joint of the front muffler. 10. Rotate the hose clamps on both heat shields so they are accessible with a screw driver and tighten each of them evenly. Note: The edge of the heat shield should just cover the weld on the inlet of each muffler, if not, adjust the heat shield for correct alignment