R1 Addendum Yamaha YZF-R1 and YZF-R6 TiForce exhaust system REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-01-2012

download
Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide more access to the exhaust nuts (flange nuts). 2. YZF-R1 ONLY!!! The EXUP control cables are tie-wrapped to the frame, and will need to be disconnected from the servo motor. Do not disconnect the electrical connection to the servo motor, and do not remove the actual servo motor. Simply remove the cables from the EXUP valve and from the servo motor. 3. Remove the existing exhaust system and save the flange nuts for reuse. Save the mounting bolt and nut for the end can to the passenger footpeg for reuse as well. 4. Inspect the exhaust gaskets. Replace if necessary. 5. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remainingsteps. Reuse the flange nuts saved from step 3 above. Make sure the ends of the headpipes fit flush and snug in the ports before tightening. 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 10. YZF-R1 ONLY!!! Place the bands approximately 180mm from the edge of the end can. See figure 2. 11. YZF-R6 ONLY!!! Place the bands approximately 195mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (step 10 or 11 / figure 2), then tighten the 6mmhardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN

2007 Kawasaki ZX6R Full System Installation

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
1. Remove the faring lowers (save STD bolts for reuse) , side faring (save STD bolts for reuse) , seat faring (save front 2 STD bolts for reuse) and right silencer cover. 2. Detach the turn signal assy, (unplug the cable coupler of turn signal and brake light at the same time) 3. Remove the radiator under bracket and lightly unscrew the radiator mounting bolt. Move the radiator forward. This will make you to have enough room for detaching exhaust pipes and flange nuts. Then, take off the standard headpipes. Detach the cable of the exhaust device and l eave servomotor stayed in the motorbody. (save (3) STD bolt and nut and (8) flange nuts for reuse) 4. Assemble the enclosed head pipes 1,2,3 and 4 by matching the 4-2-1 joint. Do not install the exhaust springs at this time. Lightly attach the assembled head pipe sections to the exhaust ports. Make sure the ends of the head pipes fit snug in the ports. 5. Install the tail joint and tail pipe to the joints. Do not install the exhaust springs yet. Jiggle the whole assemble for better fitting. Lightly attach the tail pipe by standard bolt and nut saved in step 3, but do not tighten the bolt fully. (see Image 1) *Recommend to use new gasket to prevent from leaking the exhaust. *Lightly screw the (8) STD flange nuts saved in step 3. * Cylinder number is 1, 2, 3 and 4 from the left hand side with you on the motorbike. 6. Attach enclosed silencer stay A to the place where the standard silencer mounted by (2) STD bolts and nuts saved in step 3. Reinstall the seat faring and penetrate the (2) 5x45mm to the hole of a seat faring mounted. Fix the Silencer stay A by enclosed (2) M5 nuts and (2) aluminum collar using the thread of penetrated M5x45bolts. (see Image 2 and drawing 1) Image 2 7. Insert the TiForce silencer to the tail pipe. Put silencer band and band rubber to the assembled silencer stay A by enclosed (2) M8x20mm bolt and (2) M8 washer. (see drawing 1) 8. Attach the supplied springs to all the joints. Use a spring puller to prevent damage to the springs that could lead to future failure. Put the radiator back to the original position. 9. Attach the L and R license number stay to the silencer stay A. (see Image 3) (see drawing 1) 10. Reinstall the firings detached in step 1. Attach the right silencer cover to the frame by using enclosed faring stay and (1) M6x20mm. (see drawing 1) 11. Make sure the exhaust system is free and clear of the faring. If necessary, adjust for proper clearance.. Removed the fairings reinstalled in step 10. 12. Securely tighten all fasteners in this order (from exhaust pipe flange to silencer stay) Image 3 14. Attach the turn signal assy detached in step 2 to the license number stay. (Use (4) M6x15mm) (See Image 4) Plug the cable couplers.

Incoming search terms: