Kawasaki Mule 3010 Hood Rack Installation And Operations Manual

0

Filed Under (Kawasaki) by admin on 28-04-2012

download
1. Install the Seizmik Brush Guard. – Have a friend hold the brush guard (G) in place while you slide the 1.0″ dia. tube clamps (K) in place over the middle tube of the OEM bumper, as shown in Figure 1. Secure each one in place with one of the 3/8″ x 2.25″ bolts (N), two 3/8″ washers (Q), and one 3/8″ nylock nut (R). Repeat at the top tube of the OEM bumper using the 1.5″ dia. tube clamps (J), and 3/8″ x 1.75″ bolts (O). VEHICLE FRONT Figure 2. 2. Mounting brackets – Attach the two hood rack mounting brackets to the mounting pads of the brush guard, as shown in Figure 2. Use four of the 3/8″ x 1.0″ bolts (P), eight 3/8″ washers (Q), and four 3/8″ nylock nuts (R) per mounting pad. Snug down the fasteners but do not fully tighten them yet. 3 Figure 3. 3. Crush sleeves – Insert a crush sleeve (B) into each cantilever arm assembly (C & D), as shown in Figure 3. 4. Cantilever arms – Position the Driver side cantilever arm (C) on the mounting bracket, and insert a 3/8″ dia. pivot bolt (M), as shown in Figure 4. Add a 3/8″ washer (Q) and nylock nut (R) on the other side and snug down the assembly; leave the fasteners loose enough so the components can be repositioned for fitment. Repeat this step for the passenger side. Figure 4. 4 Figure 5. 5. Lock pins – Insert the 1/2″ lock pins (Y) into the tabs on each side of the Brush Guard, fixing the cantilever arms in place, as shown in Figure 5.

Incoming search terms:

SUZUKI Hayabusa, GSXR 1000, GSXR 750, GSXR 600 Sport Brake Lever INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 21-02-2012

download
Before you install your new ASV brake lever, you MUST choose the correct brake light switch tab to install. You will find in the package with this lever one plastic bag with four smaller bags inside of it. One bag has two small phillips screws. The other three bags have small black aluminum blocks (light switch tabs) with labels on them. Part# BRC511-H is ONLY for HONDA motorcycles. Part# BRC511-STK is for all SUZUKI, TRIUMPH and 05-06 KAWASAKI ZX636R motorcycles ONLY. Part# BRC511-K is for all KAWASAKI motorcycles EXCEPT the 05-06 ZX636R . Choose the correct tab for your bike and install it onto the lever as shown in photo 2b using the two small Phillips head screws provided. It is recommended that you use locktite or another type of thread locking adhesive to make sure these screws do not come loose. Be sure to tighten these screws as tight as you can without stripping them. The brake stop / light tab is required for your ASV brake lever to work properly Carefully place the lever into the master cylinder while inserting the plunger rod into the barrel hole as shown in photo 4. Install the main pivot bolt, and tighten it until it is snug against the master cylinder. Do not over-tighten, as it could cause the lever to bind in the master cylinder

2007 KTM SX-F 250- 450 Kickstand Installation and Removal Manual Instructions

0

Filed Under (KTM) by admin on 26-01-2012

download
Remove the lower d bolt making sure you keep track of the order of the small parts for re-assembly. 2) Remove the lower in-frame bolt. 3) Install the supplied lower kickstand mounting bracket onto the frame at the lower chain roller boss. The counter bore should slide over and onto the frame boss. The chain roller should go back into place just how it came e supplied lower kickstand mounting bracket between it and the frame. Do not is bracket needs to pivot to align with the lower hole in the main . 4) Install the kickstand onto the bike using one of the provided M8x30mm flat head sub-frame to main-frame bolt location. Do not tighten yet. 5) Line up and install the other provided ad bolt thru the lower kickstand mounting hole into the supplied lower kickstand mounting bracket. 6) Now tighten all three bolts, two mounting bolts (front) and one lower kickstand mounting bracket 7) Periodically check the kickstand and all mounting bolts for tightness. Maintenance: Clean and lubricate the kickstand pivot area after each ride! We recommend using a heavy-duty chain lube. If necessary, you can remove the back cover plate for additional cleaning. Never remove the kickstand leg pivot bolt!

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SWINGARM PIVOT COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. Use rubbing alcohol to clean the swingarm surface, pivot bolt, and nut. 2. Place the larger left-side pivot cover (3) over the pivot nut. Position the set screw (4) at the bottom of the cover. Tighten set screw to 16 in-lbs (1.8 Nm) . 3. Remove adhesive backing from and apply the left-side trimplate to the swingarm. Apply pressure to the trimplate on the swingarm for one minute. 4. Remove adhesive backing from and apply an emblem to the center of the pivot cover. Apply pressure to the emblem for one minute. 5. Repeat Steps 1-4 for the right side of the swingarm. 6. Allow adhesive to cure for 24 hours before operating the vehicle. SERVICE PARTS 4 2 5 3 1 5 6 3 is01811 Figure 1. Service Parts: Swingarm Pivot Cover Kit Table 1. Service Parts: Swingarm Pivot Cover Kit Part Number Description (Quantity) Item Not Sold Separately Right-side trimplate and adhe- sive 1 Not Sold Separately Left-side trimplate and adhesive 2 Not Sold Separately Adhesive emblem (2) 3 Not Sold Separately Left-side pivot cover 4 3231B Set screw (2) 5 Not Sold Separately

HARLEY DAVIDSON CRESTED BAR AND SHIELD PASSENGER FOOTBOARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
REMOVAL 1. See Figure 1. Remove existing passenger footpegs and mounting hardware. 2. Remove chrome swingarm pivot covers, if equipped. 3. Do not remove tool boxes, if equipped. INSTALLATION NOTES To prevent damage to chrome surfaces, avoid contact with abrasive materials (stones, sand, etc.). Some paint removal from counterbore holes of footboard brackets may be necessary to ease the installation of the pivot pins. Install Left Footboard Mount and Bracket 1. See Figure 2. Position left footboard mount (1) and insert screw (2) through mount and into footpeg mounting hole. 2. Position semi-circular cutout in mount extending from side of mount around nut of swingarm pivot bolt. Tighten screw (2) to 35-45 ft-lbs (47-61 Nm). 3. Position left footboard bracket (3) on mounting stud so that bolt hole aligns with machined groove in stud. 4. Insert screw (4) through left side in split hub of footboard bracket. Thread into tapped hole (right side) of split hub. Tighten to 10 ft-lbs (13.6 Nm). Install Right Footboard Bracket 1. See Figure 2. Position right footboard bracket (5) onto muffler support bracket. 2. Secure footboard bracket with screw (6). Tighten to 35-45 ft-lbs (47-61 Nm). Install Left and Right Footboards NOTE The footboards are side specific. Install footboards with Bar and Shield logo toward the front. 1. See Figure 2. Place footboard pad (7, 8) on footboard bottom (9, 10) and thread the pivot pins (11, 12). 2. Tighten pivot pins to 60-68 in-lbs (6.8-9.0 Nm). 3. Place spring (13) into retaining hole in footboard bracket (3, 5). Rest Delrin® ball (14) on top of spring. 4. Position footboard bottom (9, 10) onto footboard bracket in the down position while being careful not to unseat the ball. 5. Tighten pivot pins to 12-15 ft-lbs (16.3-20 Nm). 6. Press down on footboard assembly so holes align. 7. Insert mounting pins (15) in footboard bottom (9, 10) into corresponding holes in footboard pad (7, 8).

HARLEY DAVIDSON PIVOT BOLT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
This kit fits all 2004 and later XL (Sportster®) model motorcycles INSTALLATION Right-Side Pivot Bolt Cover Installation Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. See Figure 1. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns. 2. Note the position of the bottom-most flat on the rear-fork pivot hex-head bolt (3). Line up the pivot bolt cover over the bolt head so the set screw is centered on the hex flat. Use the 3/32 inch hex key from the kit to tighten the set screw securely to the head of the rear-fork pivot bolt. 3. Make sure the pivot bolt cover is clean and free of any oil or grease. Remove the protective backing from the adhesive disk on the back of the decorative insert (9). Install the decorative insert onto the end of the pivot bolt cover with the image or text upright and parallel to the ground. Press the insert firmly against the end of the pivot bolt cover and hold pressure for 30 seconds. After releasing pressure, avoid direct contact with the insert for about 20 minutes. Left-Side Pivot Bolt Cover Installation 4. Models without passenger footrests: Use an 8 mm hex key to remove the bolt (5) retaining the double-tube clamp (4). Models with passenger footrests: Use an 8 mm hex key to remove the two bolts (5) and the left-side passenger footrest and bracket assembly (6). 5. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns

Incoming search terms:

Honda Goldwing GL1800 Independent Rear Suspension Trike Conversion Installation Guide

0

Filed Under (Honda) by admin on 17-02-2011

download
Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. □ Seat (to be re-installed without modification) □ Left and right side covers (to be re-installed without modification) □ Battery and battery box (to be re-installed without modification) □ Left and right saddle bags □ Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) □ Trunk (to be re-installed without modification) □ Left and right passenger foot rests (to be re-installed without modification) □ Left and right foot rest under covers (to be modified and re-installed) □ Left and right rear crash bars □ Saddle bag trunk stay (to be modified and re-installed) □ Left and right mufflers (Mufflers only, do not remove decorative covers) . Retain OEM muffler rubber mounting bushings and flanged spacers for re-installation of the mufflers. □ Rear wheel □ Left and right pivot bolt covers (to be re-installed without modification) □ Reverse resistor (to be relocated) □ Swing Arm and Driveshaft IMPORTANT : Carry out brake system modifications (See Section 5) prior to removing Swing Arm. Evacuating all the brake fluid from the system will prevent brake fluid spills when the OEM swing arm is removed. Note : Upper bolt of mono shock can be removed without removing the fuel tank. □ Rear Shock and Hydraulics. Unscrew angle sensor from OEM shock and secure to frame with cable tie. □ Shock arm and shock link Note : You may need to cut out the bolt that attaches the shock link to the frame

Yamaha Road Star Trike Conversion Installation Manual

0

Filed Under (Yamaha) by admin on 17-02-2011

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

Honda Goldwing GL1800 Independent Rear Suspension Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. □ Seat (to be re-installed without modification) □ Left and right side covers (to be re-installed without modification) □ Battery and battery box (to be re-installed without modification) □ Left and right saddle bags □ Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) □ Trunk (to be re-installed without modification) □ Left and right passenger foot rests (to be re-installed without modification) □ Left and right foot rest under covers (to be modified and re-installed) □ Left and right rear crash bars □ Saddle bag trunk stay (to be modified and re-installed) □ Left and right mufflers (Mufflers only, do not remove decorative covers) . Retain OEM muffler rubber mounting bushings and flanged spacers for re-installation of the mufflers. □ Rear wheel □ Left and right pivot bolt covers (to be re-installed without modification) □ Reverse resistor (to be relocated) □ Swing Arm and Driveshaft IMPORTANT : Carry out brake system modifications (See Section 5) prior to removing Swing Arm. Evacuating all the brake fluid from the system will prevent brake fluid spills when the OEM swing arm is removed. Note : Upper bolt of mono shock can be removed without removing the fuel tank. □ Rear Shock and Hydraulics. Unscrew angle sensor from OEM shock and secure to frame with cable tie. □ Shock arm and shock link Note : You may need to cut out the bolt that attaches the shock link to the frame Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm . 5.1 Explanation of OEM brake system and changes From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Trike Conversion Kit.

Incoming search terms: