HONDA TRX 650 RINCON 4X4, TRX 680 Rincon BLADE HARDWARE MOUNTING REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 26-12-2011

download
Push tube/ Swivel/ Blade Assembly Instructions 1. Install the blade swivel (15) onto the front of the push tube (14) using the 1/2″ shoulder bolt (4), two 1/2″ washers (5), and a 3/8″ Nylock nut (3) from the bolt bag per diagram #1. Make sure the flat washers seat properly on the bottom of the shoulder bolt while tightening the nut. Make sure the blade turns freely. 2. Remove the 2 bottom flanged nuts (I) from the u-bolt (D) and 2 from the 3/8″ bolts (H) on the blade position pin assembly (23). Run the 2 top flanged nuts up the threads of the u-bolt. Place the blade position pin assembly on the push tube as shown in the Diagram, sliding the blade position pin through one of the oval holes on the swivel and through the rear blade position pin support bracket on the push tube. 3. Re-install the u-bolt and 3/8″ bolts and flanged nuts per the Diagram. On the u-bolt, thread the bottom nuts up until they are flush with the bottom of the threads then run the top ones down, making sure the bottom nuts remain flush with the bottom of the u-bolt. Tighten all 4 bottom nuts. 4. Remove the two shoulder bolts (18) from the pivot point brackets on the back of the blade (1). Attach the blade to the swivel by sliding the ears on each side of the swivel into the pivot point brackets on the blade, reinstall the two shoulder bolts and Nylock nut (3) and tighten. 5. Hook the blade springs (6) to the two round holes on either side of the 5 oval holes on the swivel. Hook the eyebolts through the other end of the springs, push the eyebolts through the spring attaching points on the back of the blade and install 3/8″ Nylock nuts (3). Spring tension may be increased by tightening both Nylock nuts on the eyebolts evenly. 6. Install the blade stops (16) with the two 3/8″ x 1″ bolts (17) and 3/8″ nuts (3) per the Diagram. Rotating the stops allows you to change the blade pitch to suit changing conditions or materials

Incoming search terms:

2001 HONDA CRF 230 Dual Sport Kit Installation Manual

0

Filed Under (Honda) by admin on 21-11-2010

download
1. Remove the seat, fuel tank, side panels, and front number plate. 2. Taillight and Turn signal Installation: Note that Baja Designs has updated this kit to use the new style LED taillight. The mounting is the same. Mount the rear taillight assembly to the rear fender as shown in Photos 1 and 2. Transfer drill the mounting holes in the taillight assembly into the fender and mount using the countersunk fasteners provided. The tail light lens should just line up with the end of the fender. Mount the turn signals into the side of the taillight assembly as shown in Photos 1, 2 and 3. The taillight has not been pre-drilled to allow placement of the turnsignals to be varied to accommodate different exhausts. Use a 3/8″ drill for the turn signal mounting hole 3 Photo 3 Photo 2 Photo 1
. 3. Brakelight Switch Installation: This is a tight fit on the CRF230 – take your time and it’ll work. Drill a 1/8″ hole in the brake lever 4 ½” from the center of the brake pedal pivot point (Photo4). 4 Photo 5 Drill 1/8″ hole here Photo 4 Install the brake-switch bracket under the right case bolt directly above the oil filler cap (Photo 5). Attach the spring to the hole you drilled in the pedal. Adjust the switch in the bracket so it engages about halfway through the pedal throw. You may need to lengthen (stretch) the spring slightly to allow proper switch adjustment. Turn-Signal Switch Installation: Install the turn signal switch on the handlebar next to the grip as shown in Photo 6 . The switch has a single screw that pinches it together on one side. Two tabs secure the switch halves on the other side. Remove the screw to separate the halves so that it can be installed on the handlebar. When installing the switch to the handlebar, make sure the tabs are seated in their locating holes and then tighten the pinch screw. DO NOT OVER TIGHTEN THIS SCREW, as too much force can strip the body of the switch. The clutch perch may have to be moved inward slightly to make room for the switch. Run the wires along the bottom of the handle

Electronic Gear Actuator Installation Instructions

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
Fault Finding Mechanical If this is a new installation then there are checks that should be made to ensure that the unit can operate correctly. • Check the gear linkage for free play; this represents an effective loss of stroke. Tighten or replace any ball joints or other linkages as necessary • Check that you have oil in your gearbox, if the level is low the gears will run hot after a short period and become tight. • Check that the clutch is clearing properly, any clutch drag will cause the gears to mesh and prevent you changing gear cleanly. If your installation has been working satisfactorily, but has begun to change erratically check the following: • Ensure that the bearing in the clamp is tight and that there is no wear in it, if there is excessive play then replace the bearing. • If you are using a ball joint to connect to the shift lever check this for wear, replace if necessary. • Check all alignments, in particular if you have clamped onto a tubular frame it is possible that this has moved slightly over time • Check the gear linkage for free play; this represents an effective loss of stroke. Tighten or replace any ball joints or other linkages as necessary – if your linkages are all tight you may still have some play in the gearbox itself. – 3 – When offering up the actuator it must also be borne in mind that the angle between the actuators connecting rod, and the pivot point of the lever should be as near as possible to 90 degrees. This ensures that the effort is equal in both directions. When looking for a suitable mounting location you may be able to pick up on existing bolts, the back-plate on the clamp can be drilled to pick up on these. If there is no convenient mounting point then you will have to make up a transition bracket to get the unit into the correct position. The following photographs show some of the common options. See our web site for a full index of mounting arrangements

Incoming search terms:

Incoming search terms: