HARLEY DAVIDSON 360 DEGREE HIGHWAY FOOTPEG MOUNTING KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Position footpegs so rider can operate foot controls without interference. Failure to have full access to foot controls can cause loss of control, which could result in death or serious injury. (00313a) Mount the footpegs so they will not strike the ground during cornering. Foopegs striking the ground during cornering can cause loss of control, resulting in death or serious injury. (00458b) NOTE See Figure 2 for steps 2 through 6. 1. Determine what height on the engine guard you prefer for the final mounting of the footpeg mounts. Mark location, if desired. 2. See Figure 2. Obtain clamp assembly (1) from kit. Wrap the clamp halves around the engine guard and install with hinge pin head facing upward. Place the flatwasher between the ears of the clamp halves. Hold parts in posi- tion. 3. Obtain the lockwasher (13), screw (7) and one of the footpeg extensions (14) (long or short depending on kit number) from kit. 4. Position the clamp adapter (10) over the clamp assembly (1) with the “cogged” face of the adapter facing the extension arm (14). Hold clamp adapter in place. 5. Install screw (7) with internal tooth lockwasher (13) through the clamps, the clamp adapter (10) and into the extension arm (14). Position extension arm as desired. Do not tighten completely at this time. 6. Obtain the clevis/extension assembly (6) from kit. Position assembly such that footpeg pivots upward and toward the rear of the bike. NOTE: It may be necessary to loosen the screw slightly and rotate the extension to obtain this position. Tighten item 9 securely. 7 5 1 3 4 2 6 8 is02511 1. Clamp assembly 2. Arm extension 3. Clevis 4. D-washer 5. Footpeg 6. Screw 7. Clamp adapter 8. Clamp halves Figure 1. 360 Degree Footpeg Mounting Installed (Shown with Footpeg Installed) NOTE The footpeg will be a tight fit if the D-spring washer is installed correctly. 7. Refer to Figure 1. Obtain the footpeg (5), sold separately, D-spring washer (4) and screw (6) from kit. Install the D- spring washer so it is positioned inside the clevis (3) with the square “D” edge towards the inside of the mount. Hold the washer in place and slide the footpeg into position. Install the screw (6) and tighten to 19 ft-lbs (26 Nm). 8. Repeat Steps 1 through 7 for the opposite side. Position the footpeg assemblies so they are at equal heights and symmetrical. Securely tighten each assembly until it cannot be rotated on the guard with reasonable foot pressure, but do not exceed 55 ft-lbs (81 Nm) on item 7

DRIVER PEGS HONDA ADAPTOR INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Assemble the peg onto the peg adaptor by removing the allen bolt from the end of the foot peg you are using. Remove the clevis assembly (folding mechanism) from the peg itself. Assemble the peg and allen bolt on to the peg adaptors. 2. The original peg pivots or folds up on a pin and has a return spring. Note how the spring is assembled into the peg. Remove the cotter pin, washer and pivot pin and foot peg. Install the new peg and adaptor assembly onto the motorcycle in the same manner and using the same spring, pin, washer and cotter pin. Set the angle of the new peg as desired and tighten the allen bolt securely. 3. Use the small set screws located at the end of the adaptors to raise and lower the foot pegs resting position.