Honda CRF230 And CRF150 Enduro Lighting Kit Installation

0

Filed Under (Honda) by admin on 02-12-2011

download
Control Switch Installation: Install the high/low/off switch on the left handlebar next to the grip. Do not tighten the screws too tight as the threads in the body of the switch can be stripped out. Zip-tie the switch wiring down along the bottom of the handlebar and over the front of the top triple-clamp. Wiring Harness Installation: Attach the plastic connector from the switch to its corresponding mate from the provided wiring harness. Route the harness back along the left side of the bike following the stock wiring harness to the area on top of the airbox. Make sure the key is in the off position before making these wiring connections. -Run the black wire with the ring terminal and the fused lead with the ring terminal down to the battery.

Air Shock Installation Instructions

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
Air HoseInstallation. Choose the most convenient loca- tiononyour motorcycle for the air fill valve. Drilla 5/16″hole and install the air fill valve as shown in Figure 3orsecure air fill valve to frame tube. 2. Keep hose ends clean during installation because dirt can cause air leaks. 3. Install hose connector, tube clamp and two O-rings onto one end of the air hose (See Figures4&5) Apply rubber lubricant (soap solution, not oil) to the O-rings to ease installation on the air hose& into the shock absorber inlet. Plastic connector should just bottom on fitting. Do not overtighten! The function of the nut is to hold everything together in place, the O- rings do the sealing. Fin- gertightenonly (10 in/lb maximum). 4. After routing the air hose, trim the length to fit air fill valve. Install hose connector, tube clamp, and twoO-rings onto end of hose (See figures 4&5). Lubricate as above and assemble to air fill valve. Use the same procedure formating hose. Important —leaveasmall amount of slack in hose near shock absorber to allow for the slight move- mentofthe shock. Caution! Do not install hose near ex- haustsystem, battery or any other sharp edges or seat movement. Keep hoses clear of moving parts such as wheels or suspension components. Do not allow hoses to have excess slack and sag below the motorcycle. The hoses could catch on road surfaces or debris and could be damaged while the motorcycle is in motion. 5. If necessary the air hose can be secured along the motorcycle’swiringharness with tie-wraps. 6. Testing: Inflate system to 50 psi. Apply soapy water solution to all connections and check for air leaks. If there are any leaks, disconnect the suspected fitting and check for dirt or damage to the air line or the O-rings. Remove any dirt or foreign matter, re-lubricate the O-rings and reinstall. If unable to locate the leak, remove rubber boot from shocks and submerge pressurized components under water (in- cludingT-Valve) and check for leaks. If you cannot solve the air leak problem, please contact our technical staff for assistance

2008 Kawasaki KFX 450 Fuel Management Interface INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the seat. 2. Remove screws that hold on plastic gas tank cover on the left and the right side. (figure 1) 3. Remove bolts from sub-frame that hold on shrouds on the left and right side. (figure 2) 4. Remove bolts that hold on lower part of shroud connect to front fender brackets on left and right side. (figure 3&4) 5. Remove bolts connecting front body to frame on left and right side. (figure 5&6) 6. Disconnect fuel hose from gas tank. (figure 7) 7. Pull gas tank forward and disconnect the plastic connector. (figure 8) 8. Remove gas tank and plastic protector exposing fuel injector plug. 1 Instruction sheet 1 Adhesive backed Velcro square 1 FMI 3 Zip ties 2 Motoworks stickers 18550 Minthorn Street, Lake Elsinore, CA 92530 (951) 587-9222 (951) 296-1552 fax
9. Mount Motoworks FMI to plastic underneath the seat using Velcro. (figure 9) 10. Run Wires along either side of the sub frame as shown in figure 11. Route the ground wire and connect to the silver bolt on frame. (figure 10) 12. Locate fuel injector plug . (figure 11) 13. Connect the female connector into the fuel injector. 14. Connect in the original connector you removed from the fuel injector into the short pigtail male connector. 15. Reinstall quad