Sherco Engine Engine Removal and Case Splitting Manual

0

Filed Under (Sherco) by admin on 20-04-2011

download
Engine Removal and Case Splitting Preparation 1. Wash the bike and engine thoroughly. 2. Drain transmission oil by removing drain bolt and copper washer with 5mm Allen. 3. Drain coolant by removing 3 bolts of water pump cover and lifting off engine side case.4. Remove: a. rear fender- two bolts plus one long with washer using 4mm Allen b. fuel tank hose from petcock c. fuel tank- one short bolt and washer using 4mm Allen d. chain master link and chain from front sprocket e. kick starter- one large button head bolt and washer f. rear brake- one bolt/washer using 13mm wrench g. rear brake master cylinder- 2 button head bolts h. gear shifter- one bolt i. flywheel cover – 3 bolts j. clutch slave cylinder- two button head bolts using 4mm Allen k. clutch actuating rod by pulling it out of the case l. airbox three 4mm Allen bolts and loosening Phillips head carb hose clamp m. carburetor cap/slide assembly n. carburetor by loosening Phillips head manifold hose clamp o. spark plug cap p. spark plug q. header pipe 2 bolts into cylinder head r. silencer- 3 bolts (one with washer and nut using 10mm wrench) s. cylinder head coolant hose clamp and hose t. rear shock upper bolt u. radiator plastic cover bolt, then lever up the radiator with screwdriver until the radiator “legs” pop out of frame retaining holes 5. Remove flywheel using flywheel puller tool, taking care not to lose the small Woodruff
key by placing it inside of the magnetic flywheel for safe storage. 6. Remove ignition (3 bolts) and slide rubber grommet and ignition wiring assembly out of the case and out of the way, taking special note of the ignition timing marks. 7. Remove front sprocket and 2 retaining circlips. 8. Remove clutch side case and its 10 bolts using 5mm Allen, being careful not to lose to lose the 2 aluminum alignment pins (dowel pins). Insert the dowel pins into their holes within the Right Crankcase

Incoming search terms:

SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

Incoming search terms: