2003-2007 Kawasaki Ninja ZX6R/ RR HID Installation Removal Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
take out the original bulb and install the HID bulb. Be careful, do not touch the HID bulb at any time. Plug in the power wires into the original power plug. They go in easy and slide right in. Black wire connects into the black wire on the plug. On the right side, pink goes to red. On the left side, blue goes to red as these are positive wires. Pull the wires toward you slowly and carefully as you near the cover toward the headlight. Spin the rubber grommet if you need to line up the dust cover to the head light. Now lock it in. The arrow should point up if it is locked in properly. Left side installed the same way as the right. Mount the ballasts on the under side of the cowling covers with two nuts and bolts. Position the ballast in the proper place. Then, hold in one spot while drilling two holes for the bolts. An alternate mounting may be with industrial double sided tape or industrial Velcro. Do not use those cheap double sided tape of Velcro mounts as they will not hold the weight of the ballasts. Close up of underside of the cowling cover with ballast installed.
Top side of the cowling cover. Repeat installation on the second cowling. Then reinstall on the bike, connecting all the plug wires.

HONDA GL1100 Manifold Cover Installation Manual

0

Filed Under (Honda) by admin on 04-03-2011

download
Note: Read instructions carefully before installing. 1. Start with right side. Remove (2) screws and washers from each manifold tube base. NOTE: Save this hardware it will be reused. 2. Remove (4) screws and washers that hold chrome wire guide to carbs. 3. Apply a small amount of grease to the No. 10 washers (4). This will help to hold them in place on installation. 4. Place the No. 10 washers over the threaded holes in the carb base. 5. Reinstall the OEM wire guide and carefully insert 20 mm screws and lock washers. NOTE: The screws DO NOT go through the tube on the manifold covers. 6. Sandwich the tabs on the manifold cover between the carb top and the wire guide. Finger tight the screws. NOTE: Route spark plug wires OVER THE TOP of the wire guide. 7. Lift bottom of manifold cover and insert aluminum washers removed in step 1. Put smooth of washers toward manifold. You may have to use small amount of grease on these washers also to position them. 8. Position manifold cover and reinstall (2) OEM screws removed in step 1 9. REPEAT STEPS FOR THE OTHER SIDE.

HARLEY DAVIDSON CHROME SEAT POST REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
REMOVE 2 1 is00000 1. Seat Post 2. Screw Figure 2. Lower Seat Post 1. Refer to Owners Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery negative cable. 3. On motorcycles equipped with oxygen sensors, disconnect the rear sensor connector. 4. See Figure 2. Remove screw (2) and washer from the lower seat post (1) and discard. -J04294 1 of 2 5. Disconnect spark plug wires and primary wire from ignition coil. 6. See Figure 3. Loosen the bracket screws (1). Remove seat post screw (2) and seat post with ignition coil and cover. 7. See Figure 4. Remove coil cover screw (5) and cover (4) from stock seat post (1). 8. Remove ignition coil screws (3) and coil (2) from seat post. 2 1 is04241 1. Bracket Screws 2. Upper Seat Post Screw Figure 3. Upper Seat Post Fasteners 2 5 1 3 4 is04337 1. Seat Post 2. Ignition Coil 3. Coil Screw 4. Coil Cover 5. Coil Cover Screw Figure 4. Install Ignition Coil to Seat Post INSTALL 1. See Figure 4. Install ignition coil (2) to new seat post using screws (3). Tighten ignition coil screws to 10-15 ft-lbs (13.6-20.3 Nm) . 2. Install coil cover (4) to seat post with screw (5) and tighten to 30-40 in-lbs (3.4-4.5 Nm) . 3. See Figure 1. Place seat post (1) in position and attach lower post with screw (2), washers (3) and dome nut (4). Tighten screw (2) to 10-15 ft-lbs (13.6-20.3 Nm) . 4. See Figure 3. Attach upper seat post with screw (2). Tighten screw (2) to 12-15 ft-lbs (16.2-20.3 Nm) . Tighten bracket screws (1) to 12-15 (16.2-20.3 Nm) . 5. Connect primary wire to ignition coil. 6. Connect spark plug wires to ignition coil. The rear cylinder plug wire attaches to the top coil post. Ensure that spark plug wire boots are fastened securely. 7. Connect rear oxygen sensor connector, if equipped. 8. Reconnect battery negative cable

Incoming search terms: