Harley-Davidson Twin Cam Engines Performer RPM Gear Drive Camshaft Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 03-03-2012

download
1. Disconnect the battery, and remove the fuel tank. 2. On engines with the oil tank above the engine, drain the engine oil. 3. Remove the front exhaust pipe to clear the Cam Housing Cover. 4. Remove the Rocker Covers and remove the four 5/16″ bolts and the two 1/4″ bolts holding the rocker arms in place. With the rocker arms removed, remove the stock pushrods. 5. Remove the push rod tube retaining clips and push rod tubes. 6. At this point, you may remove the lifter covers and take the lifters out, or you can make a lifter holding tool from a binder clip as shown in Figure 1 INSTALLATION PROCEDURE 1. Disconnect the battery, and remove the fuel tank. 2. On engines with the oil tank above the engine, drain the engine oil. 3. Remove the front exhaust pipe to clear the Cam Housing Cover. 4. Remove the Rocker Covers and remove the four 5/16″ bolts and the two 1/4″ bolts holding the rocker arms in place. With the rocker arms removed, remove the stock pushrods. 5. Remove the push rod tube retaining clips and push rod tubes. 6. At this point, you may remove the lifter covers and take the lifters out, or you can make a lifter holding tool from a binder clip as shown in Figure 1 . 7. On pre-2000 models with a cam position sensor, you may want to remove the inspection cover, unplug the wires, and remove the sensor at this time to ease installation later on. 8. Remove the cam housing cover keeping the bolts in a separate cup. ( Note: Oil will run out of the cam housing.) 9. Using the Chain Tensioner Unloader Tool, unload pressure on the outside chain tensioner, and pin it in place with the retaining pin (See Figure 2) .

Incoming search terms:

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

HARLEY DAVIDSON TIMER COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) NOTE For kits 32972-04A, 32924-04A, 32675-04A, and 32923-04A, refer to step 1 and 2 for installation instructions. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. See Figure 2. Remove and discard the original screws and timer cover. 2. Place new timer cover (1) in position and secure with chrome screws (2). NOTE For kits 32584-88TA, 32668-98A, and 32571-98A, refer to steps 3 through 8. 3. Use a 3/8 in. drill bit and drill the heads off the original timer cover rivets. Remove original timer cover. NOTE If the inner timer cover has been riveted in place and access to the cam position sensor is required, use a left hand drill and carefully remove the rivet heads. If a right hand drill is used, the sensor plate screw heads could break off when trying to remove the rivet. NOTE To make the cam position sensor tamper proof, follow steps 4 through 6. If the cam position sensor is not required to be tamper proof, skip steps 4 through 6. 4. Remove and discard inner cover retaining screws. Leave gasket (if used) and inner cover in position. 5. See Figure 1. Place washers (4) over rivets (3) and place rivets into inner cover holes so the backs of the rivets go into the sensor plate screws’ tapped holes. 6. Use a standard rivet tool and install rivets, securing inner cover to sensor plate screws. 7. Use the self-tapping screw (5) to cut threads into the remaining inner cover holes. Discard screw after use. 8. Place new timer cover (1) in position over inner cover (A) and secure with chrome screws (2). NOTE For kit 32581-90TB, refer to steps 9 and 10. 9. Use 3/8 in. drill bit and drill the heads off the timer cover rivets. Remove original timer cover. 10. Place new timer cover in position and secure with chrome screws (Part Number 9462) from kit

Incoming search terms:

The New Kawasaki ZX-6R Trading in gets easier and easier

0

Filed Under (Kawasaki) by admin on 18-02-2011

download
didn’t go to my local Kawasaki shop expecting to trade in the 2004 636 I’d been happily riding. I honestly didn’t expect there to be anything on the floor that would motivate me to bring the bike in. Some of you reading this may be able to relate to what I am saying, the day you don’t look for something is the day that you find exactly what you didn’t know you need. That was the day I decided I needed to take home the new ZX-6R. The reworking of the new ZX-6R is more than just about looking good. According to KMC the engine has been redesigned from the crankcase up for the first time in ten years. Racing technology built into the new bike is a close-ratio cassette transmission that can be removed without the needing to split the main crankcases in case you needed to make repairs or adjustments at the track. They also tell us that the fuel injection system has shorter throttle bodies with a smaller diameter bore which claim to give this new smaller sized engine more torque in the mid-range. It also comes with a GPS – Gear Position Sensor. The new ZX-6R comes stock with a slipper clutch which is one difference between the 2004 and 2007. My 2004′s rear wheel would hop if I geared down before a corner and my engine rpms were too high. The slipper clutch allows quicker downshifts. To experience the gains of a slipper clutch you don’t have to buy a 2007 Kawasaki – it was introduced to the 636 in 2005. A quick glance at the exhaust might leave the impression that the ZX-6R comes stock with stacked twin small diameter exhaust cans but if you look closely you will see it is a single oval pipe with a shotgun styled end cap. The titanium pipe has the pre-chamber and catalyser located below the engine to keep the weight on the bike low and centered and the temperature of the under seat silencer reduced. Looking at the new Kawasaki with its fairing removed, I wonder how much more it would have cost the consumer to have an exhaust system that not only works wonders but would be worth showing off? Even if some of the systems of the new 600 look better hidden by plastic the bike does have a cohesive look and every year the fit and finish of Kawasaki’s bikes seem to get better. You can look at this bike from almost any angle and nothing jumps out at you – unless you are on the right side of the bike looking at the rear brake reservoir. It seems odd to me that they would leave the rear brake reservoir exposed. Another design feature of the smooth body of the 2007 ZX-6R is the lack of tie down points for any luggage. It can be argued that this is a bike intended for Sunday morning canyon rides or track days on weekends but if you want to take the 600 out for a weekend away then there is aftermarket solution. Ventura Racks allow you go on vacation with your bike. A Ventura Rack provides you with a frame that you attach to your bike that you can secure luggage to. There is no drilling of body work and the Ventura rack I got fit onto the bike perfectly the first try. One of the things I really like about the Ventura Rack is that you can easily attach bags that you may already have or you have the option of buying the Ventura luggage system. Just give yourself time before a motorcycle trip to pack

Kawasaki ZX-6R Trading in gets easier and easier

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
I didn’t go to my local Kawasaki shop expecting to trade in the 2004 636 I’d been happily riding. I honestly didn’t expect there to be anything on the floor that would motivate me to bring the bike in. Some of you reading this may be able to relate to what I am saying, the day you don’t look for something is the day that you find exactly what you didn’t know you need. That was the day I decided I needed to take home the new ZX-6R. The reworking of the new ZX-6R is more than just about looking good. According to KMC the engine has been redesigned from the crankcase up for the first time in ten years. Racing technology built into the new bike is a close-ratio cassette transmission that can be removed without the needing to split the main crankcases in case you needed to make repairs or adjustments at the track. They also tell us that the fuel injection system has shorter throttle bodies with a smaller diameter bore which claim to give this new smaller sized engine more torque in the mid-range. It also comes with a GPS – Gear Position Sensor. The new ZX-6R comes stock with a slipper clutch which is one difference between the 2004 and 2007. My 2004′s rear wheel would hop if I geared down before a corner and my engine rpms were too high. The slipper clutch allows quicker downshifts. To experience the gains of a slipper clutch you don’t have to buy a 2007 Kawasaki – it was introduced to the 636 in 2005. A quick glance at the exhaust might leave the impression that the ZX-6R comes stock with stacked twin small diameter exhaust cans but if you look closely you will see it is a single oval pipe with a shotgun styled end cap. The titanium pipe has the pre-chamber and catalyser located below the engine to keep the weight on the bike low and centered and the temperature of the under seat silencer reduced. Looking at the new Kawasaki with its fairing

Yamaha V Star 1300 Fuel Injected INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Be sure the main switch is in the off position during the installation process. Failure to do this will cause the “check engine” light to be set. 2. Remove seat exposing the tool tray and battery. 3. Remove the (2) 12mm Hex head bolts securing rear of tank. Prop up the rear of the tank. 4. Locate and unplug the white 4-pin connector under left side of tank as shown in figure 1. 5. Route Fuelpak as shown in figure 2. Plug Fuelpak white connectors to the factory connectors unplugged in step 4. 6. Connect brown and green wires to the negative side of the battery. 7. Route Fuelpak long black wire under right side of tank and down to the horn as shown in figure 3. Disconnect the factory black / white wire from horn. Plug in Fuelpak long black wire to horn and then connect factory black / white wire to terminal on Fuelpak black wire. 8. Locate the throttle position sensor on the throttle body located on right side of the tank. As shown in figure 4, attach T-tap to yellow / black wire on throttle position sensor. Connect Fuelpak violet wire to T-tap. 9. Using supplied Velcro, mount Fuelpak next to tool tray as shown in figure 5. 10. Reinstall tank with (2) 12mm Hex head bolts removed in step 3. 11. You are now ready to set-up your Fuelpak 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified. 7. Enter any other mode values as required for your application. 8. Turn off power. 9. Reinstall clear cover, tuck Fuelpak under seat area and reinstall seat. 10. You are now ready to ride

2001-2004 Ducati Monster S4/ R Installation Instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
1 Remove the seat. 2 Prop the fuel tank in the upright position. 3 Remove the airbox lid by disconnecting the two hooks on either side of the airbox (Fig A). Unscrew the bolts on either side of the rear of the airbox or just lift up to remove the air box. 4 Disconnect the two hoses going to the airbox. 5 Remove the velocity stacks by turning them counter-clockwise and lifting up (Fig B). 6 Remove the bolt on the underside of the airbox (Fig. C). 7 The airbox can now be moved out of the way. To totally remove the airbox disconnect the wire connectors from the front of the airbox. Fig. A Fig. B Fig. C Loosen these bolts Remove this bolt Hooks These instructions can be used on either the S4 or S4R. The air box does NOT need to be removed on the S4R. Follow steps 14-20 for the S4R 9 Plug the connectors from the PCIII in-line of the stock connectors (Fig E). The ORANGE colored wires from the PCIII go to the front cylinder and the YELLOWcolored wires go to the rear cylinder. Reinstall spring clips. 10 Locate the thottle position sensor on the underside of the throttle bodies (Fig F). Remove the connector by squeezing the spring clip

Incoming search terms:

Incoming search terms: