TOYOTA Engine Intermittent No Crank/ No Start REPAIR

0

Filed Under (Toyota Manuals) by admin on 11-10-2011

download
Some Highlander, Matrix, and RAV4 vehicles may intermittently exhibita”no crank”condition. The engine can usually be started after moving the shift lever to the Neutral position orby cycling the shift lever in and out of the Park position. Are vised neutral starts witch assembly is available to address this condition. Warranty Information OP CODE DESCRIPTION MODEL TIME OFP T1 T2 Highlander 0.9 Matrix 0.5 832131 R&RP ark/Neutral Position Switch Assembly RAV4 0.7 84540-42010 17 99 APPLICABLE WARRANTY •Thisrepairis covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 monthsor36,000 miles, whichever occurs first, from the vehicle’sin-service date. •Warranty application is limited to occurrence of the specified condition described in this bulletin.

DUCATI SUPERBIKE 848 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
Position of the motorcycle controls (fig. 3) 1) Instrument panel. 2) Key-operated ignition switch and steering lock. 3) Left-hand handlebar switch. 4) Clutch lever. 5) Rear brake pedal. 6) Right-hand handlebar switch. 7) Throttle twistgrip. 8) Front brake lever. 9) Gearchange pedal. 1 4 3 2 9 8 5 7 6 fig. 3 11 E Instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are about 3 litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. It may come on briefly if the engine is very hot, but should goout again as engine speed increases. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “Engine diagnostics light” ( amber ). The engine ECU illuminates this light steadily to indicate the presence of errors leading to engine lock. 9) “Motorcycle diagnostics” light . Illuminates when the motorcycle diagnostics detects a problem. 10) Rev limiter indicator lights . Indicator light 10A: illuminates steadily at 800rpm before intervention of the rev limiter. Indicator lights 10A + 10B: illuminate steadily 400rpm before intervention of the rev limiter. Indicator lights 10A + 10B + 10C: start flashing when the rev limiter is reached. 2 1 5 9 8 6 3 4 5 7 10B 10C 10A fig. 4 12 E 11) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 12) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for theLAP and USB data aquisition functions.

DUCATI MONSTER 696 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are approximately 3litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “EOBD engine diagnostics light” ( amber ). The engine ECU iluminates this light steadily to indicate the presence of errors leading to engine lock. 9) OVER REV indicator lights . Illuminates steadily at 800 rpm before intervention of the revlimiter. Starts flashing when the rev limiter is reached. 5 8 2 4 9 3 1 6 7 fig. 4 12 E 10) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 11) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for the LAP and USB data aquisition functions. 11 A 10 B fig. 5 13 E LCD – Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . 6) Air temperature indicator . 7) Lap time . 8) Rev counter (RPM) . 9) Lap time . 8 11 13 12 14 10 4 5 9 6 2 3 1 7 fig. 6 14 E 10) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indiactor will remain on the display until the system is reset by the Ducati Service Centre who carry outthe service. 11) LAP function (fig. 6). Indicates that the LAP has been activated. 12) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The relative menus are for the use of trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorised Ducati Service Centre. 13) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 14) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence.

Incoming search terms:

BMW R 1200 RT-P Supplementary Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
Switch Layout – Left The left handlebar switch contains the standard operating controls for the police motor. The horn switch also operates the siren air horn when the ignition is turned “On”. A supplementary switch holder is standard, containing two switch blank plugs A & B. These locations are reserved for options such as Cruise Lights, Radio Rebroadcast, Radio Speaker “off” or other desired optional rocker switches. Siren Switch: The BMW/Code 3 siren is operated by one momentary push button switch, but only when the ignition is “on”. Pressing the button engages the siren into wail tone. Each subsequent press of the button advances to yelp, then hyper-yelp, then back to wail (California models only have wail and yelp). Press and hold to turn-off siren at any time. The siren has been programmed to accept a push of the button similar to clicking a computer mouse. This was done to avoid accidentally activating siren by nudging the button. A quick, clean press or “poke” of the button provides crisp activation. Switch Layout – Right The right handlebar switch contains the standard operating controls for the police motor including starter button. However, the additional switch functions are as follows: (A) Emergency Lights: This three-position switch controls the switching power to all emergency lights. Rocking the switch down to the middle position engages rear channel for the emergency lights (remember switch (C) must be down), rocking switch (A) down further engages front and rear channels – all emergency lights (adding front and side lights). With the switch in this position, rocking switch (C) up will cancel rear lights, but keep front and side lights operating. An LED indicator display can be seen through the back of the right front LED emergency light housing, showing whether the rear or front and rear emergency light channels are switched “on