Toyota Power Steering Conversion Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
Remove the stock steering box and column. Be sure to clear the area of all wiring, brake lines and fuel lines. 2. Bolt the Toyota box to the mounting bracket so that the long arm of the bracket points in the same direction as the steering column input shaft (small shaft.) To mount the bracket and box correctly, the longer end should be towards the rear of the vehicle. It may be necessary to grind on the power steering box where the two flanges protrude above the bracket. For technical help call Classic Performance Products Monday thru Friday 8:30am to 5:00pm at (714) 522-2000. Rev. 8/17/2009 3. Locate the box/bracket assembly into the frame by centering the Toyota sector shaft through the original hole in the frame. This hole will need to be elongated approximately 3/8″ to allow the sector shaft to clear the frame. Bolt the bracket directly into the mounting holes for the original steering box. 4. With the first bolt in, check the fit by reattaching the steering box. Make sure the splined shaft goes through the frame without interference. Torque down the mounting bolts to 45 lbs. 5. Attach the pitman arm to the steering box. Before this is done the steering sector must be centered. Turn the input shaft clockwise as far as it can go. Make a reference mark. Now turn the shaft counter clockwise as far it can go and be sure to count the turns. Turn the shaft back half the distance and now the box is centered. Be sure to double and triple check this procedure. Attach the pitman arm to the output shaft with the output shaft nut. Torque the bolt down to 110ft/lbs. Reconnect the stock drag link and you are on your way

POWER STEERING CONVERSION TOYOTA LAND CRUISER REMOVAL

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
ADVANCE ADAPTERS INC. P/N: 716808 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 PAGE 4 OF 4 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 02-10-10 POWER STEERING CONVERSION TOYOTA LAND CRUISER SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships and parts stores. Installation Tips We recommend Weldless DD and Double Splined universal joints for the best steering system. Weldless DD universal joint features two set screws for maximum holding power. Position yoke, tighten set screws to mark the shaft. Remove yoke and drill the set point on the shaft. When installing the universal joint, set screws are tightened into the countersink mark, then tighten the jam nut and the shaft will not move. We recommend the use of Loctite. Spline both ends (3/4″-36) universal joint is the preferred design, as it allows the shaft to be rotated in small increments during installation to properly align or phase the steering system. The same installation procedure as the Weldless DD should be used, or it is acceptable to simply grind a flat surface on the spline to let the set screw.

Tacoma Power Steering Pump Improving Power Steering Reservoir modification

0

Filed Under (Toyota Manuals) by admin on 02-10-2011

download
For my SAS I decided to add hydraulic steering assist as it comes in real handy for rock crawling. I got the Redneck Ram setup from the folks at West Texas Off-road that includes rebuilding an earlier IFS steering box along with drilling and tapping the box for the included ram. One of the down sides of adding a ram is that it slows the steering down because the stock steering pump has to supply the added volume for the hydraulic ram. Another is that it creates a fluid volume change in the system reservoir that needs to be compensated for in some way. After doing some reading on the West Texas site about how to go about modifying a Saginaw pump and reading up on earlier Toyota pump mods for steering assist setups on the Pirate board, I decided to give it whirl and see what I could do about the Tacoma pump. Chuck Gardella was kind enough to supply me with a blown pump that I could rebuild and submit to my endless fiddling and tinkering. I plan to give him my pump in return when I get this one done and installed. You need to do something to allow for more room in the reservoir for the standard hydraulic ram assist setup so I decided to tackle the reservoir first. The reason you need the extra space is because the ram is unbalanced. That is there is a rod on one side of the cylinder and not on the other side so the volume of the fluid has to change in the system to account for the volume of the rod as it travels back and forth. I calculated the volume of the rod that I have at full stroke to be about 2 oz or so. This would equate to plus or minus up to 2 oz. in the pump reservoir. Well first off, it’s no wonder why so many folks boil their steering pumps over with heavy wheeling and have so many other steering problems. The stock power steering reservoir doesn’t even rate pint sized

1953 Toyota Ford Truck Power Steering Conversion Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 01-10-2011

download
of all wiring, brake lines and fuel lines. 2. Bolt the Toyota box to the mounting bracket so that the long arm of the bracket points in the same direction as the steering column input shaft (small shaft.) To mount the bracket and box correctly, the longer end should be towards the rear of the vehicle. It may be necessary to grind on the power steering box where the two flanges protrude above the bracket. For technical help call Classic Performance Products Monday thru Friday 8:30am to 5:00pm at (714) 522-2000. Rev. 8/17/2009 3. Locate the box/bracket assembly into the frame by centering the Toyota sector shaft through the original hole in the frame. This hole will need to be elongated approximately 3/8″ to allow the sector shaft to clear the frame. Bolt the bracket directly into the mounting holes for the original steering box. 4. With the first bolt in, check the fit by reattaching the steering box. Make sure the splined shaft goes through the frame without interference. Torque down the mounting bolts to 45 lbs. 5. Attach the pitman arm to the steering box. Before this is done the steering sector must be centered. Turn the input shaft clockwise as far as it can go. Make a reference mark. Now turn the shaft counter clockwise as far it can go and be sure to count the turns. Turn the shaft back half the distance and now the box is centered. Be sure to double and triple check this procedure. Attach the pitman arm to the output shaft with the output shaft nut. Torque the bolt down to 110ft/lbs. Reconnect the stock drag link and you are on your wa

TOYOTA L, 2L ENGINE REPAIR MANUAL FOR 2L-T ENGINE DESTINATIONS

0

Filed Under (Toyota Manuals) by admin on 09-06-2011

Downloadnot stop the engine immediately after high-speed or uphill driving or ulling trailers. Keep the engine running at idle for 20 — 120 seconds depending on the driving condition. • Avoid sudden racing or cceleration immediately after staring a cold engine. • If the urbocharger is defective and must be re- placed, first check for the ause of the defect in reference to the following items and replace arts if necessary: Engine oil level and quality Conditions under which the turbocharger was used Oil lines leading to the turbocharger • Use caution when removing and reinstalling the tur- bocharger assembly. Do not drop it or bang it against anything, and never grasp it by easily- eformed parts such as the actuator or rod when moving ¡1, • Before removing the turbocharger, plug the intake and exhaust ports and oil inlet to prevent entry of dirt or other foreign material. • If eplacing the turbocharger, check for accumula- tion of sludge particles in the oil pipes and, if necessary, replace the oil pipes. • Completely r emove the gaskets adhered to the lubrication oil pipe flange and turbocharger oil flange. • If replacing bolts or nuts, do so only with the specified new ones to guard against breakage or deformation. • If replacing the turbocharger, put in 20 cc (1.2 cu in.) of oil in the oil inlet of the new one and turn the impeller by hand to spread oil to the bearing

POWER STEERING CONVERSION TOYOTA LAND CRUISER

0

Filed Under (Toyota Manuals) by admin on 08-06-2011

Download
Advance Adapters has been manufacturing steering conversion parts for installation of the Saginaw steering boxes into Toyota vehicles for more than twelve years. The parts we furnish are of the highest quality available and we utilize only proven design components for our kits. Before you consider the conversion, we recommend that you thoroughly read and understand the complete procedure (located in the Land Cruiser Manual). Do not take short cuts on steering installations. We recommend that these conversions be installed by a qualified technician. All universal joints must be safety wired for double protection. Do not overlook any details. Remember that the control of your vehicle depends on the steering gear performance. Failure of your steering system can result in severe damage and possible injury.

Incoming search terms:

Installation Instructions for TRD’s 3.4-liter V6 Supercharger Kit 1997-2000 Tacoma,1997-1998 T-100, 1996-2000 4Runner

0

Filed Under (Toyota Manuals) by admin on 28-05-2011

Download

begin, TRD recommends you thoroughly Before you and engine compartment.thatyou don’t, grease clean the engine
If buildup  on parts could become dislodged during the procedure and fall into the engine.
• Make sure the engine has cooled fully before you begin. suggest you draw diagrams of your
• To help you later, we you disconnect anything. You can doengine’s cable routing before the same

for the vacuum hoses; however, some of the vacuum connections on your stock manifold may not be the same as those on the supercharger. To ensure the proper hose connections, refer to the diagrams in the back of this manual.
TRD supercharger has been designed to reuse most of • Thestock nuts and bolts.kitTherefore, as you remove them, keep the  them with their components or label them for location. This will assure a faster, easier installation.
B. Removal of Stock Intake Manifold (figure 1)
1. Disconnect the battery ground cable.
2. With tape or a permanent marker, mark the forward edge of the power steering and the air conditioning compressor drive belts (figure 2). This will ensure that the belts will be returned to their original positions and that they will rotate in the same direction. If you reverse the direction of rotation, it may cause the belts to fray.

Incoming search terms: