2004 Camry, Highlander & Solara OCCUPANT CLASSIFICATION SYSTEM INITIALIZATION

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
Occupant Classification System (OCS) that will enable or disable the passenger front and side airbags based on occupancy, passenger weight and seat belt latch position. Passenger front and side airbags will automatically be disabled for children and small adults when weight on the seat is less than approximately 80 lbs. (36 kg). This system will clearly indicate that the passenger airbags are enabled “ON” or disabled “OFF.” Early production models of the 2004 Solara were built with an amber-colored PASSENGER AIRBAG light. To better differentiate the PASSENGER AIRBAG light from warning lights, it has been changed to white in color. This color change does not have any effect on the meaning or operation of the light. This light remains on at all times with the key in the ON position. In the event of an OCS malfunction, both the Supplemental Restraint System (SRS) warning light and passenger airbag “OFF” indicator lights will illuminate. After finding SRS code B1650 on Camry and Solara vehicles, or a B1150 on Highlander vehicles, the next step is to check codes in the OCCUPANT DETECT menu on the Diagnostic Tester. Take necessary steps to diagnose the root cause of the OCS DTC code BEFORE initializing the system

Incoming search terms:

SMALL COOLER RACK LIGHTING SYSTEM INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 29-12-2010

download
1. Using the nuts supplied, bolt the lighting system to the rack (on some earlier production models the holes may be off slightly and require that you drill the holes in the rack larger for alignment). 2. Using a side cutting pliers, trim away the corner of the metal grating and route the wire loom thru and out the bottom of the rack as shown. Route the loom along the bottom of the rack to where the plug on the motorcycle is or will be and secure it to the rack using the cable ties supplied. 3. Cut the wires and loom to the desired length to connect to the plug on the motorcycle. Connect the wires from the loom to your mating connector (not supplied) using the wire color code shown below. If you do not have a plug on the motorcycle you will need to purchase a mating male and female five pin or wire connector set. You may also use a six pin connector set and leave one pin unused as these are more readily available. RIVCO offers a six wire molded connector set with 60″ of wire #TWC002 or a waterproof six pin connector set with dust cap #TWC00

2009 APRILIA RS125 TECHNICAL SPECIFICATIONS

0

Filed Under (Aprilia) by admin on 06-11-2010

download
1. MACHINES Aprilia RS 125 production models, as produced from 01-11-05 and available in the UK via IN Competition from 01-01-06. (any parts exclusive to the older models including the pre-1999 SP model are not permitted to be used on machines in this series). The only eligible models are designated as Euro 2 & Euro 3 New machines are supplied with race kits included through: IN Competition Unit 1 New Lane Burscough Lancs 2. DISPLACEMENT CAPACITY The displacement must remain at 124.9cc and the bore and stroke (54 x 54.5) must remain as originally produced. 3. MINIMUM WEIGHT The minimum weight at post race control must not be less than 102kg , this includes oil and water but excludes fuel. At any time during the event, the weight of the whole machine (including the tank) must not be less than the minimum weight, with a tolerance of 1kg. 4. NUMBER PLATE COLOURS The background colours and figures for Aprilia Superteens are: FRONT RED background with WHITE numbers – Nitro Newcomers Class BLACK background with WHITE numbers – Aprilia Championship Class REAR BLACK background with WHITE numbers – Both Classes Placed in accordance with the ACU regulations. 5. CARBURATION INSTRUMENTS Carburation instruments must remain as homologated. Carburettor jets and needles may be replaced. No modification, polishing or cutting is allowed. Only the 28mm bodied standard carburettor is permitted. Electronic or mechanical enriching devices must remain installed and active (If the carburettor is changed from one model to another, the appropriate wiring loom must also be installed and be operative). Bell mouths must be as originally produced by the manufacturer for the homologated machine. Throttle must be standard, quick action throttles are not permitted.
6. FUEL All machines must function on normal unleaded fuel with a maximum lead content of 0.005 g/l (unleaded) and a maximum MON of 90 (RON 102 max) and be readily available from roadside service stations nationwide. E85 Bio Fuel is also permitted when purchased from normal roadside outlets. 7. FRAME BODY AND REAR SUBFRAME Frame must remain as originally produced by the manufacturer and may not be painted. The sides of the frame body may be covered by a protective part made of composite material of the original frame colour. Nothing can be added by welding or removed by machining from the frame body. Engine mounting brackets or plates must remain as originally produced by the manufacturer. Bolt on accessories to the rear sub-frame may be removed. 8. FRONT FORKS Forks structure (spindle, stanchions, bridges, stem etc) must remain as originally produced by the manufacturer. Standard original internal parts of the forks may be modified. After market damper kits or valves may be installed. The fork caps can be modified or changed to add spring preload/compression and damping adjusters. Dust seals can be modified, changed or removed providing the fork remains totally oil sealed. Any quantity or quality of oil can be used in the front forks. The height and position of the front fork in relation to the fork crowns is free. A steering damper may be added but may not act as a steering lock device. 9. REAR FORK (Swing Arm)

Incoming search terms:

Incoming search terms: