HARLEY DAVIDSON FLSTN MUFFLER SLIP-ON KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Remove mufflers according to applicable Service Manual instructions. 3. Install clamps onto mufflers and slide onto headpipes. Install muffler with the Harley Davidson script in the top position. 1 WARNING 1 WARNING 1 of 2 4. See Service Parts Illustration: Reuse fasteners and tighten muffler clamps to 45-60 ft-lbs (61-81.3 Nm), and tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm). 5. Connect negative battery cable. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances.

HARLEY DAVIDSON SOFTAIL MUFFLER SLIP-FIT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
1. Disconnect negative battery cable. Perform this installation when the engine is cool. Installing these mufflers when the engine is hot could cause burns which could result in moderate to minor injury. 2. Remove mufflers according to applicable Service Manual instructions. Shotgun exhaust mufflers will come off the vehicle as a pair, attached together. Staggered dual mufflers will come off the vehicle attached to the interconnect tube. 3. For a shotgun exhaust, skip to Step 6. 1 CAUTION 1 WARNING 1 WARNING 1 of 2 4. Remove mufflers from interconnect tube and discard gaskets and mufflers. 5. Install mufflers to interconnect pipe using new gaskets (6) and existing screws. Slip muffler clamps (1) on mufflers and install assembly back on vehicle. Tighten screws to 96-120 in-lbs (10.8-13.6 N-m). Tighten muffler clamps to 45-60 ft-lbs (61-81.3 Nm). Attach the interconnect tube to the frame using the existing flange lock nuts and washers. Tighten to 30-33 ft-lbs (40.7- 44.7 Nm). 6. On shotgun style assemblies, assemble top and bottom mufflers using interconnect seal. Torque screws to 96-120 in-lbs (61-81.3 Nm). Attach interconnect tube to frame using existing flange locknuts and washers. Torque to 30-33 ft-lbs, (40-7-44.7 Nm). 7. Replace fasteners and tighten as follows: muffler clamps to 45-60 ft-lbs (61-81.3 Nm), flange locknut on carriage bolt to 30-33 ft-lbs (40.7-44.7 Nm) and tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm). 8. Reconnect negative battery cable. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. Noise Emission Warranty Gabilan Manufacturing, Inc. warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise standards. This warranty extends to the first person who buys these mufflers for purposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances.

HARLEY DAVIDSON DYNA STREET PERFORMANCE SLIP-ON ACCESSORY MUFFLERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
PRODUCT INFORMATION Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meets all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for purposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Loosen stock muffler clamps and remove nuts that attach mufflers to muffler support tube. Remove stock mufflers. Save all mounting hardware for reinstallation. 3. Install new kit mufflers using muffler clamps (purchased separately) and stock mounting hardware saved from Step 2. Do not tighten hardware at this time. NOTE Before tightening nuts that attach mufflers to muffler support tubes, make sure the front muffler is positioned as far forward in its brackets slot as possible. This will eliminate any possible contact between the mufflers. 4. Tighten muffler clamp bolts to 45-60 ft-lbs (61-81 Nm) . Tighten nuts that attach mufflers to muffler support tube snugly. 5. Connect the negative (-) battery cable