Honda GL 500 MiniTrike Installation Manual

0

Filed Under (Honda) by admin on 29-04-2011

download
Refer to diagram for bracket identification 1. Secure motorcycle in an upright stable position 2. Attach bracket A (left) to rear footpeg mount. 3. Attach bracket B (right) to rear footpeg mount. 4. Remove rear saddlebags. 5. Attach top of brackets C/D to saddlebag sub frame hardware as in photo. Place enclosed 3/8 spacer between brackets C/D and inside of sub frame. 6. Attach axles and wheels to MiniTrike frame and place in proper position and relation behind motorcycle. 7. Attach bracket A (left) / B (right) to TOP of forward attaching points on MiniTrike frame. 8. Attach bottom of brackets C/D to rear mounting plate on MiniTrike frame 9. Ensure MiniTrike is square with motorcycle and tighten all bolts. 10. Remount saddlebags. Wheel Alignment Wheel alignment is critical for proper tire wear and handling. With MiniTrike installed measure A and B . Loosen axle plates and align wheel so A and B are equal to within 1/16th of an inch. Tighten axle bolts and torque to 45 pounds. Repeat for C and D . It may be necessary to shim axle plates for proper alignment. NOTE : The measurement of A and B may not be the same as C and D. This is normal and presents no difficulty

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

Vento Rebellian 150 Brackets MiniTrike Installation Manual

0

Filed Under (Vento) by admin on 02-11-2010

download
Secure motorcycle in an upright stable position 2. Remove center stand. 3. Attach bracket A to center stand mount. 4. Remove saddle bags. 5. Insert longer bolts provided from inside saddle bag through bracket F (left)/ G (right) and attach to rear motorcycle sub frame. 6. Attach bracket D (left) / E (right) to TOP of forward MiniTrike attachment point. 7. Attach axles and wheels to MiniTrike frame and place in proper position and relation behind motorcycle. 8. Attach bottom of bracket H (left) / I (right) to rear MiniTrike frame attachment point and top of H/I to rear of brackets F/G. 9. Attach bracket B (left) / C (right) to BOTTOM of brackets D/E and TOP of attaching arm on bracket A. 10. Ensure MiniTrike is square with motorcycle and carefully tighten all bolts.

BMW Airhead Side Braces Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
Figure B shows the upper end of the Airhead Side Brace where it attaches to the frame ( NOTE: Leave at least 1/2″ spacing below the bottom edge of the fuel tank ). Figure C shows how the Airhead Side Brace must clear the air inlet tubing Figure D showing how the lower edge (beveled end) fits the frame at the rear of the bike. Figure E shows one of the threaded cones properly welded to the frame, and painted. . Ensure Airhead Side Braces are fully assembled (threaded cones firmly bolted into the braces at both ends). 2. Hold Airhead Side Brace in their proper position (reference Figures A-D) to mark location where front and rear threaded cones will be welded to the frame. NOTE : The lower (rear) end of the Airhead Side Brace is beveled, for reference. NOTE : Make sure that both the left and right Airhead Side Braces are positioned equally. 3. Mark the frame and remove paint in the appropriate areas using emery cloth to prepare the frame surface for welding. NOTE : Measure and mark twice, weld once! 4. Hold assembled Airhead Side Braces in their appropriate positions and tack-weld at the top and bottom. Perform this step for both the top (front) and bottom (rear) ends of the Airhead Side Braces , on both sides of the bike. 5. Using removable tape, mark each Airhead Side Brace as either “left” or “right”, to make sure they are replaced onto the appropriate side of the bike after disassembly. 6. Remove the bolts, and the Airhead Side Braces from the tack-welded, threaded cones. Complete the welding of the threaded cone to the motorcycle frame at all 4 locations. 7. Clean/remove any weld splatter, and paint to protect threaded cone and frame from corrosion (see Figure E). 8. Re-assemble Airhead Side Braces onto threaded cones maintaining original left side/right side orientation. NOTE : The lower (rear) end of the Airhead Side Brace is beveled, for reference. 9. Torque hex bolts to 7 ft/lbs

Incoming search terms: