KTM Front Wheel Bearing Installation Manuals

0

Filed Under (KTM) by admin on 31-01-2012

download
1 Place motorcycle on a stand so that the front wheel is off the ground. 2 Using a 27mm socket remove the front axle nut. Using a 10mm socket, loosen the four front axle pinch bolts. Slide front axle out of forks and remove front wheel. 3 Insert a long punch (with a good square edge) into the center of the aluminum wheel bearing spacers and push up against the inner edge of the spacer on the opposite side of the wheel (Fig. 1). Using a hammer, tap the punch around the entire circumference of the spacer until it completely slides out of the bearing (Fig. 2). Turn the wheel over and remove the other spacer in the same way. 4 Use a long screwdriver or narrow pry bar and pry the seals out of each side of the wheel (Fig. 3). 5 Using snap ring pliers, remove the bearing retaining snap ring from the brake rotor side of the wheel. (Fig. 4) NOTE: 2003 – CURRENT MODELS USING # 16-092 KIT DO NOT USE THIS SNAP RING. 6 Insert a long punch (with a good square edge) into the center of the wheel bearing, and push up against the inner edge of the bearing on the opposite side of the wheel. Using a hammer, tap the punch around the entire circumference of the bearing until it completely slides out of the hub. Turn the wheel over and remove the other bearing in the same way. NOTE: It may be necessary to tap on the punch sideways at first to knock the center aluminum sleeve off center so that you are able to get the punch on the edge of the bearing. 7 Clean areas where bearings will be inserted back into hub and apply a thin coat of grease around the machined hub surface. Tap the bearing on the snap ring (if used, either side if not) side of the hub into the machined hub surface, making sure to keep it square with the hub as it goes in and only tap on the outer race of the bearing. Once you get the bearing flush with the outer edge of the hub, use a socket or piece of pipe that is just smaller than the outside diameter of the bearing to finish tapping the bearing into the hub. (Fig. 5) 8 Install the bearing retainer snap ring (if used) into the groove machined in the hub, and then tap the seal in place over the snap ring with the spring on the seal in towards the center of the wheel. Tap in the aluminum spacer in the center of the seal.

Incoming search terms:

KTM 3V TURBO DRIVE MODEL 9808T KNEE FEED Installation and Removal Manual

0

Filed Under (KTM) by admin on 28-01-2012

download
Gather together the following items that you will need to complete this installation. a) lathe b) 3/8″ electric hand drill c) 9/32″ diameter transfer punch SERVO Turbo Drive Model 9808T Page 2 d) .4375 drill, 3/16″ drill, #7 drill e) 1/4-20 tap f) 3/4″ socket wrench g) set of inch hex wrenches h) clean shop rag Step 2: Clean the power feed mounting area completely. Step 3: Remove the drive clutch nut and the drive clutch from the elevating jack shaft. Step 4: Remove the dial nut, dial, and dial carrier. Keep the dial for reuse later. Step 5: Remove the existing bearing retainer. Keep the screws for reuse later. Step 6: Pull jack shaft out of knee. Hold inboard end up while removing to avoid damage to the pinion gear. Step 7: Press the bearing off the jack shaft. Step 8: Drill and ream the end of the jack shaft .4375″ diameter by 13/16″ deep. The .4375″ dia. must be concentric to the shaft O.D. within .002″ T.I.R. Chamfer 1/32″ x 1/2″ diameter. For best results, machining should be done in a lathe. Step 9: Place the shaft extension #6975 into the end of the jack shaft. Finish drill 3/16″ diameter through the shaft and pin the extension with the 3/16″ diameter x 5/8″ long roll pin. File smooth. Step 10: Reassemble and replace the jack shaft in the machine. Step 11: Replace the existing bearing retainer with #57904 retainer provided. Secure using existing screws. Step 12: Slip spacer #5426 and bearing race #1616 onto the jack shaft. Slide the adaptor #0771 over the bearing race and locate against front of the knee.

Incoming search terms:

HARLEY DAVIDSON ULTRA TOUR-PAK BRAKE LAMP CHROME ACCENT COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Installation- Corner Brake Lamp Trim 1. Carefully cut out brake lamp trim template (1) attached to this instruction sheet. 2. Position template (1) on plastic brake housing (2) as shown in Figure 2. 3. Using a punch, score two points indicated on template to mark mounting hole locations (3) on plastic brake housing (2). 4. Using a 1/8 in. drill bit, drill a pilot hole in plastic housing. 5. Use a 7/32 in. drill bit to drill through housing and fiberglass Tour-Pak. 6. See Figure 3. Insert studs on chrome brake lamp trim piece through holes drilled in plastic housing and Tour- Pak. Using two flatwashers (1), two lockwashers (2) and two acorn nuts (3) from kit, secure trim piece to Tour- Pak. Tighten finger tight. 7. See Figure 3. Locate brake lamp retaining clip (4) on inside of Tour-Pak and remove. Save clip (4) for later reinstallation. 8. Form chrome trim around corner of Tour-Pak, so that it is positioned around plastic housing evenly. While holding chrome trim in position, mark forward mounting hole position on Tour-Pak using a punch

Incoming search terms: