HONDA GL1800 DRIVER BOARDS WITH HEEL/ TOE SHIFT INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Place the motorcycle on its centerstand. Remove the stock foot pegs and mounts (four 6mm wrench size allen screws) 2. Beginning on the left or shift side remove the rubber cover from the shift pedal. (Some WD-40 or armor all will make it much easier). Using a hacksaw cut the retaining knob off the end of the shift pedal as shown in photo #1A. Don’t worry should you ever remove the floorboards you can replace the rubber and glue it in place. 3. Install the left floorboard assembly being sure the fork in the toe-heel shifter goes over the shift pedal. Install the two original bolts and snug them. 4. Locate the black plastic shift bushing (see photo #2A) notice the set screw on the side of the bushing slide the bushing onto the shift pedal with the small diameter going on first and engaging the fork on the toe-heel shifter. The shoulder of the bushing should be touching but not putting a side force on the fork. Rotate the bushing so that the set screw is at 9 o’clock tighten the set screw. Locate the rubber cap provided and install it over the end of the stock shift pedal. (See photo #2B). 5. Next rock or pivot the floorboard assembly up and down noting the play between the bolts and bolt holes. Position the floorboard half way between these two extremes then tighten the bolts securely. Check for clearance between the bottom of the toe shifter and the floorboard (min. 1/8″) by pushing the toe shifter down until it stops while rotating the rear wheel (see photo 2C). If there is not sufficient clearance loosen the two mounting screws and pivot the floorboard to obtain the1/8″ clearance and retighten the screws. If installing the heel shifter into one of the two optional forward mounting holes check for the 1/8″ clearance while rotating the rear wheel and up shifting. 6. On the right side remove the 12mm brake pedal mounting bolt, notice the punch mark on the pedal shaft that aligns with the slot in the pedal. The pedal MUST be re-installed in the same position. Pull the pedal outward and off the shaft. 7. See photo (3). On the bottom side of the footpad make a mark ¾” from the rear and outside edge as shown. Drill a ¼” hole thru the pedal at the mark. See photo (4) lay the brake pedal extension upside down on a bench and place the stock pedal into the opening as shown, while holding the two pieces firmly together and using the hole drilled earlier as a guide drill a ¼” hole thru the bottom of the pedal extension. Turn the two pieces over, using a needle nose pliers insert the ¼” bolt provided from the top down thru both pieces, install the lock nut provided and tighten securely. Carefully align the punch mark with the slot on the pedal and re-install the brake pedal (should the shaft slide inward you will need to remove the chrome side cover and hold the shaft outward using your finger as shown in photo (5A). Install the original 12mm bolt and tighten securely

Incoming search terms:

SUZUKI M109 BRAKE PEDAL INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 29-01-2011

download
1. Remove the pinch bolt from the bottom of the stock brake pedal. Notice that the slot in the pedal aligns with a punch mark on the end of the shaft. Using a needle- nose pliers disconnect the return spring from the pedal. Remove the pedal by sliding it outward until it touches the foot peg mount and then pushing the shaft inward. 2. Remove the pinch bolt from the new brake pedal and install it so that the slot is aligned with the punch mark on the end of the shaft. Install the pinch bolt and tighten it securely. Reconnect the pedal return spring

HONDA VTX1300, VTX1800 R, C & S MODEL HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-12-2010

download
1 .Lay a blanket folded several times over the fuel tank to protect it. 2. Notice on the 1800 models that there is a small punch mark on the handlebars located on the right hand, front side of the handlebars where the risers meet the top clamp/speedometer housing. This is to reference the handlebar position when re-assembling. On the 1300 models there is a punch mark on the forward facing side of the clamp, these must be installed the same way. 3. Loosen the two 19mm nuts holding the risers to the upper triple clamp (steering head). 4. Pry out the four chrome caps covering the handlebar bolts. Remove the four handlebar clamp bolts. (6mm allen wrench). While sitting on the motorcycle, pull the handlebars and upper clamp off of the risers. They may be slightly stuck and require some force to get free. Lay the handlebar and/or upper clamp/gauge assembly carefully on the blanket. 5. Remove the 19mm nuts and the risers from the triple clamp. NOTE: Be careful not to scratch the upper triple clamp when installing the new risers. Place the thin flat washers provided into the recess at the top of the riser bolt holes on the triple clamp. Assemble the lock washers provided and then the original flat washers onto the bolts provided. Install the new risers onto the triple clamp and snug the bolts. 6. Re-install the handlebars and upper clamp/gauge assembly. ( Remember the punch marks) Tighten the front bolts first closing the gap at the front, and then tighten the rear bolts. Tighten the two 19mm riser-mounting bolts securely. Check for adequate clearance and proper routing of cables and hoses.

2003-2004 HONDA GL 1800/A Frame Weld Safety Recall

0

Filed Under (Honda) by admin on 15-12-2010

download
there is no punch mark on the VIN plate as specified in this Service Bulletin, proceed to the REPAIR PROCEDURE section of this Service Bulletin. IMPORTANT: Due to the complexity of this campaign it is imperative that you check iN and your Dealer Responsibility Report before you begin repairs. If iN or your Dealer Responsibility Report indicate the Safety Recall has been performed, but you confirm the unit is not punched and the repair has actually been done (by inspecting the weld), please contact the Warranty HelpLine at (800) 421-1900, option 7. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510)  Frame Weld Inspection Chart (S0516) You MUST provide your TIG welder with the following items:  2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511)  2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) Welding Template Box (S0512) All of the above items were shipped to you with Service Bulletin GL1800 #14. If you need additional copies of these materials, you may order them from Resolve at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. DISASSEMBLY OVERVIEW You will be removing the following components from the vehicle as instructed in the Dealer Booklet : Handlebar weights Rear view mirrors Swingarm pivot covers Rider foot pegs Seat Side covers/Engine side covers Fairing pockets Fairing molding Meter panel Top shelter Battery Fuel tank Main wiring harness ground Front lower fairing Front exhaust pipe protector Muffler/exhaust pipe Antenna Whip(s) Coolant reserve tank Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: Before you send the motorcycle to the welder, you MUST check for lower crossmember frame weld cracks.  If your inspection reveals no cracks in or on either the Left or Right lower cross- member frame welds, proceed to the REPAIR PROCEDURE OVERVIEW section of this Service Bulletin.  If your inspection identifies a crack or cracks in or on either the Left or Right lower crossmember frame welds, perform the following procedure: Place the grinding template (S0512) on the crossmember. Using a suitable felt marker, draw a line on the weld with the crack, drawing the line along the entire edge of the the template (this line will be 89 mm long). If the crack falls within the length of this line (89 mm) , prepare the motorcycle for welding per the Dealer Procedures and advise the welder to use the Cracked Weld Repair Manual (S0515). After the bike has returned from the welder, prepare the frame and re-assemble the motorcycle per the Dealer Procedures . Then, proceed

Incoming search terms: