Harley-Davidson feuling Adjustable Pushrods Installation Instructions

0

Filed Under (Harley Davidson) by admin on 22-04-2012

download
1. Refer to the proper factory service manual for your model and year of engine, for removal of existing pushrods. 2. The Feuling pushrods are designed with a small adjustment parameter for rigidity creating maximum lift – These are not quick install pushrods and may require the removal of the lifter blocks and or loosing of the breathers/rocker arms supports. When loosening the rocker arm supports always remove the breather bolts first. 3. Clean and inspect each new Feuling pushrod including center oil hole 4. Feuling pushrods are marked Intake and Exhaust. The shorter pushrods are Intake and the longer pushrods Exhaust 5. Feuling recommends using new O-rings and gaskets where applicable to prevent oil leaks
6. Always pump up hydraulic lifters before installing them. Use an oil squirt can to fill the lifter with oil through the feed hole on the side of the lifter, push oil through the feed hole until the air bubbles are gone. If needed work the oil back and forth through the feed hole and pushrod seat with the squirt can. Light weight oil can be helpful. 7. Assemble and adjust one cylinder at a time, the servicing cylinder needs to be on TDC of compression stroke so the cam lobes are at their lowest point 8. Install pushrods into proper locations with the adjusting side of the pushrod down, towards the lifter. Slide the pushrods through the pushrod covers up into the rocker housing and set the pushrod on the seat of the lifter. We recommend filling the pushrods with oil then maneuver the pushrod up into the rocker arm seat. 9. Torque rocker arm housings and breathers to factory torque spec’s 10. See the instructions for your lifters for the proper adjustment. All Feuling hydraulic lifters run best at . 090″ – . 100″ of crush.

Incoming search terms:

Yamaha Forward Control Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 17-01-2012

download
After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use

HARLEY DAVIDSON PUSHROD COVER RETAINER INSTALLATION AND REMOVAL TOOL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
Figure 1. Pushrod Cover Retainer Installation and Removal Tool There are no Service Parts available with this kit. REMOVAL 1. See Figure 2. Insert the pin of the pushrod cover retainer tool into the retainer loop with the back of the tool towards the cylinder fins. Rotate the tool towards the cylinder to remove the pushrod cover retainer. INSTALLATION 2. See Figure 3. Load the pushrod cover retainer into the tool as shown in figure 3. Place the top edge of pushrod cover against top edge of push rod. 3. See Figure 4. Place the tool on top of the spring cover. Pivot the tool upward to install the pushrod cover retainer is05892a Figure 2. Removing Pushrod Cover Retainer is05895a Figure 3. Loading Pushrod Cover Retainer in Tool is05893a Figure 4. Pushrod Cover Retainer Installation

Incoming search terms:

HARLEY DAVIDSON CHROME BILLET LIFTER-COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
Installation with Stock Pushrods Refer to the service manual for your motorcycle model. Installation with Adjustable Pushrods Lifter-Cover Removal Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 1. Set the lifters of the rear cylinder to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 2. See Figure 1. Insert a screwdriver into the slot on the side of the spring-cap retainer on the pushrod cover. 3. Press the spring-cap and retainer down while pulling outward to remove the spring-cap retainer. 4. See Figure 2. Lift the lower pushrod cover to reveal the lower third of the pushrod. 5. If the engine has stock pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 6. If the engine already has adjustable pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 7 6. Use a bolt cutter or similar tool to cut the stock pushrod. Avoid cutting the pushrods with a saw, grinder, or other method that may allow metal debris into the engine. Go to step 8. 7. Loosen the jam nut on each adjustable pushrod and resize each rod to its shortest length. 8. Remove the pushrod covers and pushrods from the engine. 9. Remove the O-rings from the seats in the engine at the top and bottom of the pushrod cover. 10. Remove the four screws fastening the lifter cover to the engine to remove the cover and gasket. 11. Remove old lifter-cover gasket material from the engine, taking care not to allow material to fall into the engine. Continue to Lifter-Cover Installation in this I-Sheet. Lifter-Cover Installation 1. See Figure 3. Verify that the lifter anti-rotation pin is in position. Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 2. Verify that the cylinder lifters are set to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 3. Fasten the new lifter-cover gasket and chrome billet lifter cover to the engine using the chrome screws from this kit. In a cross pattern, torque the lifter-cover screws to 90 – 120 in-lbs (10.2 – 13.6 Nm). 4. See Figure 4. Loosen the jam nut on all of the pushrods and adjust the pushrods to their shortest length. NOTE See Figures 4 and 5. Install the narrow-band pushrods in the cylinder-intake location. Install the wide-band pushrods in the cylinder-exhaust location. 5. Assemble the O-rings (purchased separately) and pushrod covers. 6. Install the pushrods with the pushrod covers. The adjustment-end of the pushrod must be on the lifter

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE PERFECT FIT PUSHRODS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the service manual and follow the instructions given for disassembling the motorcycle for service and to gain access to the top end overhaul disassembly of seat, rocker cover, breather assembly, rocker arm support plate and pushrods. 2. Place the motorcycle on a center stand with the rear wheel raised off the ground. Remove the spark plugs. 3. With the transmission in gear, use the rear wheel to turn the engine over until both front cylinder tappets are at their lowest point. Remove and discard the pushrods. 4. Install the new pushrods into the pushrod covers using the appropriate service manual procedures. Be sure the larger end of the tapered pushrods are installed to the tappet sockets. 5. Repeat step 4 for the rear cylinder. NOTE Check for contact between the pushrods and the upper pushrod covers. Check by rotating the engine slowly until both valves have fully opened and closed on the cylinder you are checking. If contact is observed, the rocker arm supports should be shifted toward the engine’s cam side. 6. Complete all the appropriate service manual procedures for assembling the engine. 7. Complete all service manual procedures for the assembly of the motorcycle. 8. Return the transmission to neutral and install the spark plugs. 9. Connect the negative (-) battery cable. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 10. Install the seat

Incoming search terms:

Bajaj Removing And refitting Automatic Cam Chain Tensioner

0

Filed Under (Bajaj) by admin on 31-10-2010

download
1. Remove the 2 Flanged Bolts securing the Tensioner Assembly. 2. Remove Tensioner Assembly from the engine block. 3. Unscrew and remove Lock Bolt. 4. Remove Pushrod, Ball & Retainer, Spring and “O” ring. Clean parts thoroughly and apply grease to the Balls & Retainer. Re-assembly procedure : 1. Place Spring on Pushrod and compress the spring beyond the hole in the Pushrod. 2. Insert a pin or wire into the hole in the Pushrod to hold the Spring in its’ compressed position. 3. Place Balls & Retainer onto Pushrod. 4. Insert Pushrod into the Tensioner body with the small flat on the Pushrod facing, and aligned with, the Locking Bolt hole. 5. Insert the Locking Bolt and tighten it against the small flat on the Pushrod to lock the Pushrod in the compressed position. Remove the pin that’s holding the Spring compressed. 6. Install the Tensioner assembly onto the cylinder block and install and tighten both Flanged Bolts. Be sure that the “O” ring has been installed at the base of the flange. 7.Looosen the Lock Bolt to release the Pushrod, then re-tighten the lock bolt

Incoming search terms:

Harley-Davidson Twin Cam 88 S&S Billet Rocker Covers Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-10-2010

download
Failure to confirm pushrod/lifter placement before proceeding with installation can result in damage to rocker arm support plates and other parts. With pushrods at lowest point, front piston will be at TDC on Compression stroke. 4. Remove breather cover and baffle assembly. See Picture 2. 5. Remove rocker arm/rocker support plate. See Picture 3. NOTE – Gradually loosen rocker arm support bolts in following sequence (See Figure 1): 1. Left (driveside) rear 2. Right (camside) front 3. Right (camside) rear 4. Left (driveside) front Loosen bolts in sequence and in 1⁄ 4 -turnincrements for first 3⁄ 4 turn. Bolts can then be removed according to normal procedure. 6. Remove lower rocker housing bolts. NOTE – Gradually loosen lower rocker housing bolts in following sequence (See Figure 2): 1. Right (camside) front 2. Left (driveside) rear 3. Left (driveside) front 4. Right (camside) rear 5. Center front 6. Center rear Loosen bolts in sequence and in 1⁄ 4 -turn increments for first 3⁄ 4 turn. Bolts can then be removed according to normal procedure. 7. Remove lower rocker housing and gasket from head. Remove oil and any remaining gasket material from cylinder head gasket surface and clean gasket surface with lacquer thinner

Incoming search terms: