HARLEY DAVIDSON DETACHABLE PASSENGER BACKREST LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
INSTALLATION 1. See Figure 1. If not already assembled in package, assemble V-logo onto each mounting bracket (2 and 3) using #4-40 thread-forming screws (5). 2. Position luggage rack between sideplates of detachable passenger backrest assembly. 3. Thread button head screws (7) through washers (6), then through holes in luggage rack support and passenger backrest sideplate and into mounting brackets (2 and 3). Apply LOCTITE 243 (Blue) to screws (7) before installation. Finger tighten. 4. Tighten button head screws to 19 ft-lbs (26 Nm) . NOTE The backrest shown in Figure 1 is not included in this kit and must be purchased separately. -J01851 1 of 2 SERVICE PARTS 8 1 7 6 3 2 4 5 is04290 Figure 1. Service Parts: Detachable Passenger Backrest Luggage Rack Kit Table 1. Service Parts Table Part Number Description (Quantity) Item Part Number Description (Quantity) Item 2711 Screw, #4-40 thread-forming, steel, zinc plated (4) 5 Not sold separately Passenger backrest rack kit 1 94066-90T Washer, chrome (4) 6 53046-00 Bracket, mounting, right side (includes items 4 and 5) 2 94392-92T Button head screw, hex socket, chrome (4) 7 53045-00 Bracket, mounting, left side (includes items 4 and 5) 3 Not Sold Separately Warning label 8 Not sold separately V-logo (2) 4

Incoming search terms:

HARLEY DAVIDSON FLHTCUSE TOUR-PAK INSTALLATION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 26-03-2011

download
INSTALLATION Prepare Motorcycle for Service 1. See the Owner’s Manual and remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Remove the bolt and negative (-) battery cable from the battery. 7 6 5 4 3 1 2 is01951 1. Loading coil assembly 2. Nut 3. Lock shroud 4. Clip, locking (Sold Separately) 5. Nut 6. Screw 7. Tour-Pak lockset Figure 1. Antenna Loading Coil and Tour-Pak Lock Installation 3. Remove the bolt and positive (+) battery cable from the battery. 4. Install a Tour-Pak Rack kit (53276-04, 53118-98A or 53260-02) according to the Instruction Sheet contained in the kit. 5. For FLHX and FLTR models: Install Antenna Relocation kit according to the instruction sheet in that kit. NOTE Discard antenna mounts from antenna relocation kit and use mounts supplied with this kit. To open the Tour-Pak prior to installing the Tour-Pak lock, insert a flat head screwdriver into the lock location and turn clockwise while pulling up on the lid. 6. Install the Tour-Pak onto the Tour-Pak Rack using the hardware included in the Tour-Pak Rack kit according to Instruction Sheet included with that kit. Install Tour-Pak Components

HARLEY DAVIDSON VRSCF LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
REMOVAL 1. See Figure 1. Remove four rear fender mounting bolts (1) and washers (2). If necessary, move the ECM to access the four fender mounting bolts. 2. Disconnect the tail lamp following the instructions in the appropriate service manual. 1 2 is05463 1. Bolt (4) 2. Washer (4) Figure 1. Fender Mounting Bolts INSTALLATION NOTE There are bosses molded into the inside of the fender to use as the hole drilling templates. 1. See Figure 2. Apply masking tape to the outside painted surface of the fender at the three hole locations (1 and 2). This will protect the painted surface during the drilling operation. 2. Put the fender on a work bench, painted surface down. Use clean, soft cloth between the fender and the work bench to protect the paint finish. NOTES Drilling each hole in the fender is a two-step procedure that requires a specific type of drill bit to avoid damaging the fender. 3. See Figure 2. Use a 1/2-inch spade bit or 1/2-inch unibit (do not use a spiral-type drill bit) to drill three holes from the inside of the fender through the three pilot hole bosses (1 and 2). Stop drilling when the tip of the bit just pierces the outside surface of the fender. 4. Turn the fender over so the painted surface is now facing up. Complete each hole by using the same 1/2-inch drill bit at each of the pierced holes. Clean excess material from the holes and clean the fender surface of any debris. 5. See Figure 5. Remove the masking tape from the holes and apply the protective tape (3) to the painted surface using the drilled holes for alignment. 6. See Figure 3. Put the luggage rack (1) upside down on the work bench and align the holes in the luggage rack with the holes in the fender (2).

HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

Incoming search terms:

Triumph Scrambler And Bonneville Single Seat And Rack Kit Fitting Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
To help prevent damage to the seat and rack kit, carry out the following procedures on a soft, non-abrasive surface. cdrt 1 2 3 1
3 cowl to the seat on each side. Tighten the screws to 3 Nm. 1. Seat cowl (right-hand side shown) 2. M5 bolt and washer 7. Undo and remove the screws and flanged sleeves located at the rear of the original seat. 1. Seat screws 8. Remove the original seat. NOTE •Retain the original seat for re-use if the motorcycle is returned to original condition. 9. Fit the new seat and rack assembly using the original fixings. Locate the seat to the frame ensuring the locating tongue on the underside of the seat is positioned beneath the fuel tank bridge. Tighten the seat screws to 10 Nm. 1 2 cdrw 1 2 1 Warning The maximum load that may be carried on the luggage rack is 5 Kg (11 lbs). Incorrect loading of the luggage rack may result in an unsafe riding condition leading to loss of motorcycle control and an accident. Always ensure any loads carried are evenly distributed on both sides of the motorcycle. Ensure that the load is correctly secured such that it will not move around while the motorcycle is in motion. Check the load security regularly (though not while the motorcycle is in motion) and ensure that the load does not extend beyond the rear of the motorcycle. Never exceed the maximum vehicle loading weight of 217 Kg (477 lbs). Warning The luggage rack must not be used to carry sharp objects, or objects which extend beyond the extremities of the rack. Carriage of such items may interfere with, or distract, the rider or passenger and could affect the stability and handling of the motorcycle leading to loss of control and an acciden

Incoming search terms: